AT-LP60-BT Wireless Turntable Installation and Operation Pages 2-9 AT-LP60-BT Tourne-disque sans fil Installation et utilisation Pages 10-17 AT-LP60-BT Tocadiscos inalámbrico Instalación y funcionamiento Páginas 18-25 IMPORTANT: Turntable belt needs to be attached or turntable will not operate. See page 5 for instructions. For assistance, contact our Audio Solutions Department at 330-686-2600 x5000 or audio-solutions@atus.com.
Wireless Turntable Introduction Thank you for purchasing the AT-LP60-BT wireless turntable. AudioTechnica has been a leading manufacturer of innovative stereo phonograph products for more than 50 years. We are pleased to provide this turntable, with its excellent performance and many convenient features, for your enjoyment.
English Wireless Turntable (continued) Important information FCC Notice Warning: • To prevent fire or shock hazard, do not expose this apparatus to rain or moisture. Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Main Features Figure 1 11 Front SPEED 33 45 START STOP 1 2 Back PHONO LINE ANALOG OUT AT-LP60-BT WIRELESS TURNTABLE 4 3 16 17 10 10 9 7 8 12 5 12" 6 SIZE 7" 1 START BUTTON Engages the motor/platter and begins automatic operation. 9 45-RPM ADAPTER (shown in receptacle) Adapts 7" records with large center holes to fit center spindle. 2 STOP BUTTON Disengages the motor/platter and returns tone arm to rest.
English Initial Setup Assembling the Turntable The AT-LP60-BT requires some assembly before first use. IMPORTANT: Do not connect the AC power cable until assembly is complete. 1. Carefully place the turntable platter on the center spindle, making certain the platter is fully seated on the spindle. 2. While holding both ends of the red tape ribbon on the turntable belt, carefully pull the belt over the brass motor pulley (Fig. 2a).
Initial Setup (continued) Connecting to Stereo System (Wireless Connection) About Pairing To connect the turntable to a Bluetooth receiver device, the turntable needs to pair (register) with the device. Once it is paired, you will not need to pair it again with that device, except in the following cases: • If the turntable is deleted from the Bluetooth receiver device connection history, • If the turntable is sent out for repair, • If the turntable is paired with 9 devices or more.
English Operation (continued) Caution: When the tone arm reaches the end of the record, it will lift and return to the tone arm rest automatically. When this happens, do not interfere with the tone arm’s motion, or damage to the mechanism may occur. If the tone arm does not return automatically to the tone arm rest after the record has finished playing, simply press the STOP button to complete operation. Figure 6 Figure 7 Manual Operation 1. Remove the stylus guard from the stylus assembly (Fig. 4).
Troubleshooting Turntable does not operate 1. Make certain the turntable’s AC cable is plugged into an AC outlet, and that the AC outlet is “live.” 2. Figure 11 – Checking the drive belt 11a Check the drive belt to make certain it is on correctly. (See Fig. 11.) A) Remove the record mat from the turntable platter (Fig. 11a). Place the mat in the cardboard packaging sleeve for safekeeping.
English Specifications Tips For Better Performance • When opening or closing the turntable cover, handle it gently, moving it either at the center or equally from both sides. • Do not touch the stylus tip with your fingers; avoid bumping the stylus on the turntable mat or a record’s edge. • Clean the stylus tip frequently, using a soft brush with a back-to-front motion only. • If you use a stylus cleaning fluid, use it very sparingly.
Visit our Web Site: www.audio-technica.com One-Year Limited Warranty Audio-Technica brand products purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to A.T.U.S.
Audio-Technica Corporation ©2016 Audio-Technica Corp. 169501420C 2016.