Specification

audio-technica phono cartridges guide - 2019/20 - 45
Moving coil cartridges specification for mono vintage records
for 78rpm Shellac SP Records for Mono Vinyl for Mono Vinyl
Model Number AT-MONO3/SP AT-MONO3/LP AT33 MONO
Type
Horizontal Mono Moving Coil (see note n°5) Horizontal Mono Moving Coil (see note n°5) Horizontal Mono Moving Coil
Body Material
A
luminium/Synthetic Resin
A
luminium/Synthetic Resin
A
luminium/Synthetic Resin
Frequency Response
2
0 to 15,000 Hz
2
0 to 20,000 Hz
2
0 to 20,000 Hz
Ou
tput Voltage
1
.2 mV (at 1 kHz,12 cm/sec)
1
.2 mV (at 1 kHz, 5.0 cm/sec)
0
.35 mV (at 1 kHz, 5.0 cm/sec)
Vertical Tracking Angle
23 degrees 23 degrees 23 degrees (see note n°1)
Vertical Tracking Force Range
3
to 7 g (standard 5.0 g)
1
.5 to 2.5 g (standard 2.0 g)
2
.3 to 2.7 g (standard 2.5 g
Stylus Shape
Conical C
onical
C
onical
Stylus Curvature Radius
2
.5 mil (see note n°4)
0
.6 mil (see note n°4)
0
.65 mil (see note n°4)
Stylus Construction & Size
Bonded round shank Bonded round shank Nude square shank
Cantilever
A
luminium Pipe
A
luminium Pipe
D
uralumin Pipe
Static Compliance
1
0 x 10
– 6
cm / dyne 20 x 10
– 6
cm / dyne 20 x 10
– 6
cm / dyne
D
ynamic Compliance
3
.5 x 10
– 6
cm / dyne (100 Hz) 7 x 10
– 6
cm / dyne (100 Hz) 6 x 10
– 6
cm / dyne (100 Hz)
Wire Used for Coil
P
COCC (see note n°2)
P
COCC (see note n°2)
P
COCC (see note n°2)
R
ecommended Load Impedance
400 W to 47,000 W (see note n°6) 4
00 W to 47,000 W (see note n°6)
M
in 100 W (see note n°3)
C
oil Impedance
40 W (1 kHz) 4
0 W (1 kHz)
1
0 W (1 kHz)
DC Resistance 40 W 40 W 10 W
Coil Inductance
190 mH (1 kHz) 1
90 mH (1 kHz)
2
8 mH (1 kHz)
Cartridge Weight
6
.8 g
6
.8 g
6
.9 g
D
imensions
1
6.0 (H) x 16.6 (W) x 26.5 (L) mm
1
6.0 (H) x 16.6 (W) x 26.5 (L) mm
1
6.0 (H) x 16.6 (W) x 26.5 (L) mm
Mounting
1/2” centers 1/2” centers 1/2” centers
A
ccessories Included
Non‑magnetic screw driver; 1 brush; 2 washers; Non‑magnetic screw driver; 1 brush; 2 washers; Non‑magnetic screw driver; 1 brush; 2 washers;
2 x 20 mm mounting screws; 2 x 13 mm mounting screws; 2 x 20 mm mounting screws; 2 x 13 mm mounting screws; 2 x 19 mm mounting screws; 2 x 13 mm mounting screws;
2 x nuts; 1 plastic protector; 1 set of PCOCC lead wires AT6101 2 x nuts; 1 plastic protector; 1 set of PCOCC lead wires AT6101 1 plastic protector; 2 x nuts; 1 set of PCOCC lead wires AT6101
(1)
Vertical tracking angle of 20 degree is IEC/DIN standard.
(2)
PCOCC = Pure Copper by Ohno Continuous Casting process.
(3)
When head amplifier connected.
(4)
The abbreviation mil is equal a thousandth of an inch - mil = 0,001 inch = 0,0254 mm = 25,4 mm
(5)
Due to high output voltage this moving coil cartridge can be used directly in MM phono inputs without the use of a step-up transformer.
(6)
When connected to the MC input of a transformer-less phono pre-amp, choose a lower gain position due to the high output voltage (1.2 mV).
Model Number AT-XP 7 AT-XP5 AT-XP 3
Type Moving Magnet VM Cartridge Moving Magnet VM Cartridge Moving Magnet VM Cartridge
Mounting
H
alf
‑in
ch
Half‑in
ch
H
alf
‑in
ch
Frequency Response
2
0 to 20,000 Hz
2
0 to 18,000 Hz
2
0 to 18,000 Hz
Channel Separation
22 dB (1 kHz) 20 dB (1 kHz) 20 dB (1 kHz)
Output Channel Balance
2
.0 dB (1 kHz)
2
.0 dB (1 kHz)
2
.0 dB (1 kHz)
Output Voltage
6
.0 mV (at 1 kHz, 5 cm/sec)
5
.5 mV (at 1 kHz, 5 cm/sec)
5
.5 mV (at 1 kHz, 5 cm/sec)
Vertical Tracking Angle
2
0 degree (see note n°1)
2
0 degree (see note n°1)
2
0 degree (see note n°1)
Vertical Tracking Force Range
2
.0 to 4.0 g (standard 3g)
2
.0 to 4.0 g (standard 3g)
2
.0 to 4.0 g (standard 3g)
Stylus Shape
E
lliptical bonded
E
lliptical bonded
C
onical bonded
Stylus Size
0
.3 x 0.7 mil (see note n°4)
0
.3 x 0.7 mil (see note n°4)
0
.6 mil (see note n°4)
Stylus Construction
B
onded Round Shank
B
onded Round Shank
B
onded Round Shank
Cantilever
A
luminium tapererd tube
C
arbon reinforced ABS
C
arbon reinforced ABS
Coil Impedance
6
,700 ohms (1 kHz)
6
,700 ohms (1 kHz)
6
,700 ohms (1 kHz)
Static Compliance
2
0 x 10
– 6
cm / dyne 20 x 10
– 6
cm /dyne 20 x 10
– 6
cm /dyne
Dynamic Compliance
8
.0 x 10
– 6
cm / dyne (100 Hz) 6.0 x 10
– 6
cm / dyne (100 Hz) 6.0 x 10
– 6
cm / dyne (100 Hz)
Recommended Load Impedance
47,000 W 4
7,000 W 47,000 W
Recommended Load Capacitance
1
00
‑2
00 pF
1
00
‑2
00 pF
1
00
‑2
00 pF
Weight
6.2g 6.2g 6.2g
Dimensions
1
7.2 (H) x 17.8 (W) x 28.3 (L) mm
1
7.2 (H) x 17.8 (W) x 28.3 (L) mm
1
7.2 (H) x 17.8 (W) x 28.3 (L) mm
Replacement Stylus
A
TN
‑XP
7
A
TN
‑XP5 A
TN
‑XP
3
Accessories Included
C
artridge installation screws 11 mm x 2,8 mm x 2;
C
artridge installation screws 11 mm x 2,8 mm x 2;
C
artridge installation screws 11 mm x 2,8 mm x 2;
W
asher x 2; Nut x 2; Non
‑m
agnetic screwdriver x 1
W
asher x 2; Nut x 2; Non
‑m
agnetic screwdriver x 1
W
asher x 2; Nut x 2; Non
‑m
agnetic screwdriver x 1
(1) Vertical tracking angle of 20 degree is IEC/DIN standard.
(
4) The abbreviation mil is equal to a thousandth of an inch
‑ mil = 0,001 inch = 0,0254 mm = 25,4
m m
XP series audiophile DJ moving magnet cartridges specifications
XP Series pre-mounted cartridge-headshell sets specifications
Model Number AT-XP7/H AT-XP5/ H AT-XP3 /H
Dimensions H21.2×W21.4×L62.4mm H21.2×W21.4×L62.4mm H21.2×W21.4×L62.4mm
Weight 15.6g 15.6g 15.6g