ATH-ANC700BT User Manual Wireless Noise-Cancelling Headphones
Introduction Thank you for purchasing this Audio-Technica product. Before using the product, please read through the Quick Start Guide and Caution Guide, as well as this user manual when necessary, to ensure that you use the product correctly. Safety precautions Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product.
Safety precautions Cautions for rechargeable battery The product is equipped with a rechargeable battery (lithium polymer battery). • If battery fluid gets into eyes, do not rub them. Rinse thoroughly with clean water such as tap water and consult a doctor immediately.
Notes on use • Be sure to read the connected device’s user manual before use. • Audio-Technica will not be liable in any way for any loss of data in the unlikely event that such losses should occur while using the product. • On public transportation or in other public places, keep the volume low so as not to disturb other people. • Minimize the volume on your device before connecting the product. • When using the product in a dry environment, you may feel a tingling sensation in your ears.
About the active noise-cancelling function The product is designed to use its built-in microphone to pick up noise from the surrounding environment (noise from vehicles, noise from air conditioners, etc.) and to cancel out that noise by producing sounds in negative phase. This results in a reduction in the sounds in your environment. • The product’s noise-cancelling function mainly reduces noises of 300 Hz or lower.
Part names and functions Headband L/R (left/right) indicator Slider Arm Joint Earpad Housing A built-in microphone (for talking) is integrated into the L (left) housing. Touch panel (L) Multi-indicator lamp Used to play/pause music and video, answer/end phone calls, adjust the volume, and turn the noise-cancelling function on/off. Displays the operating status and battery level of the product. Noise-cancelling indicator lamp Displays the operating status of the noise-cancelling function.
Charging the battery • Fully charge the battery when using it for the first time. • When the rechargeable battery is running low, the product will sound 2 sets of 2 beeps through the headphones, and the multi-indicator lamp will flash in red. When these beeps sound, charge the battery. • It takes about 5 hours to charge the battery fully (this time may vary depending on usage conditions).
Connecting via Bluetooth wireless technology About pairing To connect the product to a Bluetooth device, the product needs to pair (register) with the device. Once they are paired, you do not need to pair them again. However, you need to pair again in the following cases: • If the product is deleted from the Bluetooth device’s connection history • If the product is sent out for repair • If 9 or more devices are paired (This product can save the pairing information of up to 8 devices.
Using the product The product can use Bluetooth wireless technology to connect to your device and play music, receive phone calls, etc. Use the product for whichever of these purposes suits your needs. Note that Audio-Technica cannot guarantee the operation of displays, such as the battery level display, or applications via Bluetooth devices.
Using the product Swivel mechanism You can fold the housing so that it lies flat. After folding it flat, you can also fold the housing inside the headband. • The swivel mechanism cannot rotate more than 90 degrees. Do not apply excessive force to this mechanism. “R” (RIGHT) side Joint Folded down and flat “L” (LEFT) side Folding compactly Using the joint as a fulcrum, the housing can be folded into the headband. • When folding the product, detach the included cable.
Using the product Listening to audio • To connect for the first time, pair the product and your device via Bluetooth wireless technology. Once they are paired, turn on the Bluetooth device’s Bluetooth connection, and then turn on the product. • Use your Bluetooth device to start playback, referring to the device’s user manual as necessary. • The touch panel is on the L side housing. Touch panel (L side housing) Touch Touch and hold Plays or pauses music and videos.
Using the product Using the noise-cancelling function The built-in microphones pick up the noise around you, allowing the product to produce a sound-cancelling signal to effectively reduce the noise. The noise-cancelling function turns on automatically when you turn on the power to the product. You can turn the noise-cancelling function on or off by covering the 3 points on the touch panel with your palm as shown in the figure.
Using the product Wired connection (playthrough function) This product features a playthrough function that allows it to be used as a pair of traditional headphones, even if the battery becomes depleted. Connect the connector plug of the included cable to the product’s connector jack, and then connect the input plug to your portable player so you can use it. If the product has some remaining battery power, you can use the noise-cancelling function even while you are using the playthrough function.
Cleaning Get into the habit of regularly cleaning the product to ensure that it lasts for a long time. Do not use alcohol, paint thinners or other solvents for cleaning purposes. • To clean the product, wipe it with a dry cloth. • Wipe away perspiration or any other dirt from the cable with a dry cloth immediately after use. Failure to clean the cable may cause it to deteriorate and harden over time, resulting in malfunctions. • Wipe the plug with a dry cloth if it is dirty.
Troubleshooting Problem Solution Power is not supplied • Charge the product. Unable to pair • Confirm that the Bluetooth device communicates using Ver. 2.1+EDR or higher. • Place the product and the Bluetooth device within 1 m (3.3’) of each other. • Set the profiles for the Bluetooth device. For procedures on how to set profiles, refer to the Bluetooth device’s user manual. • Remove the pairing information for the product and the Bluetooth device, and then pair the product with the device again.
Troubleshooting SBC priority connections (for when sound is delayed significantly) When the connection codec is AAC, significant sound delays can be alleviated by changing the connection codec to SBC, which comes standard with Bluetooth devices.*1 Connecting to an SBC priority connection When the pairing with a Bluetooth device has been completed 1. Turn on the product. 2. With music or video paused, cover the 3 points on the touch panel with your palm as shown in the figure.
Multi-indicator lamp display The indicator lamp of the product indicates the product’s status as explained below. Status Pairing Connection Battery level Multi-indicator lamp display pattern Red White Searching for device Flashing in intervals of 0.5 seconds Searching for device (when using an SBC priority connection) Flashing 2 times in intervals of 0.
Specifications Headphones Type Active noise-cancelling Driver 40 mm Sensitivity 98 dB/mW (When noise-cancellation used)*1 95 dB/mW (When noise-cancellation not used)*1 Maximum input power 1,000 mW*1 Frequency response 5 to 40,000 Hz Impedance 150 ohms (When noise-cancellation used)*1 35 ohms (When noise-cancellation not used)*1 Microphone Type Electret condenser Polar pattern Omnidirectional Sensitivity -44 dB (1 V/Pa, at 1 kHz) Frequency response 50 to 4,000 Hz Communication specificati
Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan ©2018 Audio-Technica Corporation Global Support Contact: www.at-globalsupport.com 132313670-02-01 ver.1 2018.2.