3000 Series Frequency-agile True Diversity UHF Wireless System Installation and Operation -TUNER- ON OFF POWER ALERT A B UHF SYNTHESIZED DIVERSITY RECEIVER ATW-R3100b MODE/SET
3000 Series Installation and Operation This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This device complies with INDUSTRY CANADA R.S.S. 210, en conformité avec IC: RSS-210/CNR210. Operation is subject to the following conditions: 1) This device may not cause harmful interference and 2) this device must accept any interference received, including interference which may cause undesired operation.
3000 Series Installation and Operation is detected, reducing the possibility of interference. As a result, 3000 Series transmitters and receivers must be used together and should not be used with components from other Audio-Technica wireless systems, or with those of other manufacturers. Exception: 3000 Series components are compatible with Audio-Technica 1800 Series wireless system components. Receiver Controls and Functions Front Panel Controls and Functions Fig.
3000 Series Installation and Operation be to the left (ground connected). If hum caused by a ground loop occurs, slide switch to the right (ground lifted). 12. BALANCED AUDIO OUTPUT JACK: XLRM-type connector. A standard 2-conductor shielded cable can be used to connect the receiver output to a balanced microphone-level input on a mixer or integrated amplifier. 13. UNBALANCED AUDIO OUTPUT JACK: 1/4" phone jack. Can be connected to an unbalanced aux-level input of a mixer, guitar amp or tape recorder. 14.
3000 Series Installation and Operation The squelch level is adjustable from 15 dB (the default value) to 39 dB in 6 dB steps. Increasing the squelch level – also called “tightening the squelch” – can cause a reduction in useable range of the wireless transmitter, so use the lowest value that reliably mutes the unwanted RF signals. (If interference is a problem, first consider trying a different frequency.
3000 Series Installation and Operation modulation. When the transmitter is un-muted, it produces both RF and audio. To mute the transmitter (cut off the audio, but continue the RF output), press and release the Power/Mute button once. A small “MUTE” will appear in the LCD window, just below the frequency (Fig. M-2) and the power/mute LED will change from green to red. To un-mute the transmitter (restore the audio), press and release the Power/Mute button once again.
3000 Series Installation and Operation UniPak® Transmitter Functions Function Menu Default Setting* Handheld Transmitter Functions Choices (Edit)▲▼ Wrap-around (Transmitter powers-up at Frequency) Function Menu Default Setting* Choices (Edit)▲▼ Wraparound** (Transmitter powers-up at Frequency) ▲▼ Frequency Lowest in band† All frequencies in band Yes ▲▼ Frequency Lowest in band† All frequencies in band Yes ▲▼ RF RF LOW RF LOW, RF HI Yes ▲▼ RF Power RF LOW RF LOW, RF HI Yes +6
3000 Series Installation and Operation Transmitter Setup Battery Selection and Installation Each transmitter uses two 1.5V AA batteries, not included. Alkaline type is recommended; other types of 1.5V AA batteries (including rechargeable) may be used, however performance may vary. Always replace both batteries. Make certain the transmitter power is Off before replacing batteries. UniPak ® Transmitter Battery Installation 1.
3000 Series Installation and Operation System Operation Turn the receiver on by pressing in the Power switch. Do not switch on the transmitter yet. The Alert indicator and the LCD window will light up; the normaloperation LCD display will appear after 1-2 seconds (Fig. D-1). If any of the bars show in the “RF” bar-graph meter, there may be RF interference in the area. If this occurs, select another frequency as explained below.
3000 Series Installation and Operation 4. Use the Up/Down arrow buttons to change the second three digits to the desired frequency. 5. To activate this frequency selection, press and hold the Set button until the word “STORED” appears in the transmitter’s window. (If you do not wish to complete this selection, just press the Set button once: the word “ESCAPE” will appear briefly in the window and the transmitter will return to the Menu mode.) 6.
3000 Series Installation and Operation Troubleshooting Guide Receiver is not on (LCD window does not light). • Receiver Power switch is not pressed in. • Small DC power cord from included in-line power supply is not plugged into jack on back of receiver. (Use the cord hook to secure it.) • The in-line power supply is not plugged into AC power outlet. • AC power is not present at the AC outlet. Receiver is on (LCD window lights).
3000 Series Installation and Operation Specifications† Overall System UHF Operating Frequencies Frequency Range Band C: 541.500 to 566.375 MHz Band D: 655.500 to 680.375 MHz Band E: 795.500 to 820.000 MHz Band F: 840.125 to 864.900 MHz Band G: 721.500 to 746.375 MHz Band I: 482.000 to 507.000 MHz Band U: 606.000 to 631.000 MHz Number of Frequencies 996 996 981 953 996 1001 1001 Not all frequencies are available in all areas. Please check with local regulations.
3000 Series Installation and Operation C-Band Scan Plan (541.500 – 566.375 MHz) F-Band Scan Plan (840.125 – 864.900 MHz)* Scan - 1 Scan - 2 Scan - 3 Scan - 4 Scan - 5 Scan - 6 Scan - 7 Scan - 8 Scan - 9 Scan - 1 Scan - 2 Scan - 3 Scan - 4 Scan - 5 Scan - 6 Scan-7 Scan - 8 Scan - 9 1 542.750 541.500 541.500 548.125 541.500 541.700 542.750 541.500 541.750 1 840.375 840.500 846.850 846.250 846.100 855.275 863.100 840.125 840.375 2 545.500 542.750 542.125 548.
3000 Series Installation and Operation U-Band Scan Plan (606.000 – 631.000 MHz) Scan - 1 Scan - 2 Scan - 3 Scan - 4 Scan - 5 Scan - 6 Scan - 7 Scan - 8 Scan - 9 1 606.100 614.000 606.100 614.125 614.300 614.100 614.750 614.125 614.375 2 606.350 619.500 606.350 614.375 615.000 614.500 615.500 614.625 614.875 3 606.850 622.000 606.850 614.875 616.225 616.025 616.500 615.375 615.625 4 607.100 623.125 607.100 615.125 616.975 616.775 617.250 615.875 616.
Statement of Compliance
Audio-Technica U.S., Inc. 1221 Commerce Drive, Stow, Ohio 44224 USA +1 (330) 686-2600 Audio-Technica Limited Old Lane, Leeds LS11 8AG England +44 (0) 113 277 1441 Audio-Technica (Greater China) Limited Unit K, 9/F., Kaiser Est. (Ph.2) 51 Man Yue St. Kowloon, HK. +852-2356-9268 Audio-Technica (S.E.A.) Pte. Ltd. No 1 Ubi View, #01-14 Focus One, Singapore 408555 +65-6749-5686 Audio-Technica Corporation 2206, Naruse Machida, Tokyo Japan ©2010 Audio-Technica U.S., Inc. audio-technica.