3000 Series User Manual UHF Wireless Systems ATW-R3210 Receiver ATW-T3201 Body-Pack Transmitter ATW-T3202 Handheld Transmitter
Contents Introduction..................................................................................2 Troubleshooting..........................................................................26 Important information..................................................................2 ATW-R3210.................................................................................................... 26 Notes on use................................................................................
Introduction Thank you for purchasing this Audio-Technica product. Before using the product, read through this user manual to ensure that you will use the product correctly. Please keep this manual for future reference. Important information Warning: For customers in the USA FCC Notice Warning: • To prevent fire or shock hazard, do not expose this apparatus to rain or moisture. Caution: This device complies with Part 15 of the FCC Rules.
Notes on use • Be sure to read the user manual for any microphone or cable that you attach to the product. • Disconnect the AC adapter from the outlet when this product is not in use. • Turn off the power of this product before connecting or disconnecting cables. • If you use the product near a TV or radio antenna, you may hear unwanted noise in the television or radio. If this occurs, move the product away from the device. • Two waves of the same frequency can't be used simultaneously.
Part names and functions ATW-R3210 Front panel ❶ ❶ ❷ ❸ Power button ( ❷ ❸ ❹ ) Use to turn the receiver on or off. IR sync window Use to IR SYNC with the transmitter (ATW-T3201, ATW-T3202). Display Displays the receiver state and setting menus. ❹ BACK button ❺ Control dial Press to take the display back one screen. Returns to the Main screen when pressed and held. Switches the screen when you turn the dial. Displays the setting menu when you press the dial.
Part names and functions Rear panel ❻ ❷ ❶ ❶ Antenna input jack ❷ Unbalanced output terminal (6.3 mm mono jack) ❸ ❸ Each jack supplies DC12 V to a connected antenna. Additionally other compatible accessories (sold separately) can be connected. Balanced output jack (XLR 3-pin male) GND HOT COLD ❹ Ground lift switch ❺ DC input terminal ❻ This switch isolates the GND pin of the balanced/unbalanced output from the ground.
Part names and functions ATW-T3201 ❶ ❺ ❹ ❷ ❸ ❻ ❼ ❶ ❷ ❽ ❾ ❿ ⓫ ⓬ ⓮ ⓭ ⓯ ❼ Transmission antenna ❽ MUTE switch Switches audio mute on and off. ❸ Indicator ❹ Function button ❺ Input connector LED that shows the status of the transmitter. When the power is turned ON: Solid green When the transmitter is muted: Solid red Pin 2: Instrument input ⓯ Display Shows the current status. If no buttons are pressed for a period of 30 seconds, the display will turn off. 6 Use to select various settings.
Part names and functions ATW-T3202 ❶ ❷ ❸ ❹ ❺ ❻ ❼❽ ❶ ❷ ❸ ❹ ⓫ ❾ Display ❿ Shows the current status. If no buttons are pressed for a period of 30 seconds, the display will turn off. ⓫ Grip case UP button Use to select various settings. BACK button ❻ IR sync window ❽ ❿ Interchangeable microphone capsule ❺ ❼ ❾ Press to return to the previous screen. Returns to the Main screen when pressed and held. Use to IR SYNC with the receiver (ATW-R3210). DOWN button Use to select various settings.
How to insert batteries ATW-T3201 1. ATW-T3202 Slide the battery cover latches down. 1. Rotate the grip case of the battery compartment. 2. Open the battery cover. • Put your finger on the hook of the battery cover and pull it to open the battery cover. 2. Open the battery cover while the latches are slid. 3. 3. Insert the batteries according to the plus (+) and minus (-) marks found inside the battery compartment.
How to attach and detach the interchangeable microphone capsule (only for ATW-T3202) How to attach 1. Attach the microphone capsule to the body of the transmitter. 2. Rotate the microphone capsule clockwise to tighten it. How to remove 1. Rotate the microphone capsule counterclockwise to loosen it. 2. Detach the microphone capsule from the body of the transmitter. • Do not directly touch or scratch the connection surface.
How to read the display ATW-R3210 Main screen ❶ TX ❷ A ❸ B HPF ❼ Transmitter information display area ❷ RF level indicator ❹ ❼ ❽ ❾ Displays the strength of RF reception for antennas A & B. Name display ❿ Displays the specified name. Frequency indicator ⓫ Displays the set frequency. Receiver mute indicator ❻ AF level indicator MHz ❽ Information on the connected transmitter is displayed. Refer to "Transmitter information display area" (p. 10) for screen display.
How to read the display Level meter screen ❶ ❷ TX-RF PWR 30 mW RF TX AF RX ❸ ❶ ❷ ❸ -92 A B 12 dB 10 dB -86 -80 -74 dBm OL -40 -30 -24 -18 -15 -12 -10 -8 -6 -4 -2 ❹ 0 +2 +4 +6 dBu ❻ ❺ ❹ RF power indicator (transmitter) ❺ Marker (when the minimum hold function is on) Shows the minimum level at which the RF is held. ❻ Mute indicator A speaker icon with a slash through it is displayed when transmitter is muted.
How to read the display ATW-T3201/ATW-T3202 The main screen is displayed when the power is switched on. If you press the UP/Down button on the main screen, the screen display is switched. ❶ ❻ 000.000 MHz ❼ VOCAL1 Gr : 02 Ch : 05 HPF ❷ ❶ ❷ ❸ ❸ ❹ ❺ ❽ HPF HPF ❷ ❸ ❺ ❹ ❹ Frequency indicator Displays the set frequency. ❷ RF power indicator : RF Power High (30 mW) Lock status indicator : RF Power Low (10 mW) RF OFF ❺ Battery level indicator : 75% or more battery power remaining.
How to operate Basic operation 1. Using IR SYNC Turn on the power button of the receiver (ATW-R3210). This function allows you to make settings on the receiver that are specified for the transmitter. • The display lights and the main screen is displayed. 1. 2. When IR SYNC is initiated on the receiver, the “Communication in standby” screen is displayed. Position the IR sync windows of the receiver and transmitter so they face each other. ATW-T3201 2. Set the operating frequency. 3.
Settings Various settings can be made from the menu screen shown on the display. ATW-T3201/ATW-T3202 1. Press the SET button. • The menu screen appears. ATW-R3210 1. ATW-T3201 ATW-T3202 Press the control dial. • The main menu screen appears. 2. 2. TX A B HPF VOCAL1 UTILITIES FREQUENCY 000 .000 MHz 0 000.000 30mW RF 3. Press the UP/DOWN button to select the item you wish to set. Turn the control dial to select the item you wish to set.
Setting ATW-R3210 Setting by group/channel List of setting items FREQUENCY 1. From the menu screen, turn the control dial, select [FREQUENCY] and then press the control dial. 2. Select [Gr/Ch] and press the control dial. Set the squelch level. 3. Turn the control dial to set the group. When finished setting it, press the control dial. LOCK Set this function to prevent the receiver settings from being changed. 4. ANT PWR Set whether to turn power on or off to the antenna input terminals.
Setting ATW-R3210 Setting the audio output level 1. From the menu screen, turn the control dial, select [AUDIO] and then press the control dial. 2. Turn the control dial to set the audio output level. Setting transmitters via IR SYNC This function allows you to make transmitter settings on the receiver and then automatically configure the transmitter via IR SYNC. The following are the available settings and setting values: Settings • The level changes 2dB +/- each time you turn the control dial.
Setting ATW-R3210 Setting the squelch level Setting the system-related functions Setting automatically Setting the lock 1. From the menu screen, turn the control dial, select [SQUELCH] and then press the control dial. Set this function to prevent the receiver settings from being changed. • The default setting is [Unlock]. 2. Turn the control dial, select [AUTO] and then press the control dial. 3. 1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
Setting ATW-R3210 Setting user-defined scan groups Setting the backup frequency mode Aside from the ten preset groups, there are two additional user-defined scan groups: U1 and U2. Both U1 and U2 can be edited with up to 32 frequencies. If you set the backup frequency in advance, you can switch the frequency of the transmitter and receiver with the transmitter. It is convenient to set this function when you want to switch the frequency easily. 1.
Setting ATW-R3210 Setting the AF level meter on the main screen Resetting Switch the AF level meter on the main screen between [Receiver (Rx)] and [Transmitter (Tx)]. • The default setting is [Rx]. This returns the receiver settings to their factory defaults. 1. 2. 3. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial. Turn the control dial, select [AF METER] and then press the control dial.
Setting ATW-T3201/ATW-T3202 Setting by group/channel List of setting items FREQUENCY MANUAL 1. Set the transmission frequency. Gr/Ch NAME Set the channel name. GAIN Set the gain. RF POWER Set the transmission output. HPF Set HPF (High-Pass Filter). LOCK Set a lock. Fn BUTTON Set the function allocation for function button. MUTE MODE (ATW-T3201 only) Set the mute mode. UTILITIES BATTERY Set the type of batteries used. LED Set whether to constantly keep indicator turned on or off.
Setting ATW-T3201/ATW-T3202 Adjusting the gain 1. Setting lock From the menu screen, press the UP/DOWN button to select [GAIN], and then press the SET button. 1. From the menu screen, press the UP/DOWN button to select [LOCK], and then press the SET button. GAIN LOCK 0dB 2. Unlock Press the UP/DOWN button to select the gain you wish to set. 2. • The level changes 2dB +/- each time you press the UP/DOWN button. • It can be set from -10 to +20 dB. 3.
Setting ATW-T3201/ATW-T3202 Setting the indicator Setting the mute mode (only for ATW-T3201) The indicator LED can be turned [On] or [Off]. • The default setting is [On]. Set the function of the MUTE switch. 1. From the menu screen, press the UP/DOWN button to select [MUTE MODE], and then press the SET button. 1. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button. MUTE MODE Mute 2.
Setting ATW-T3201/ATW-T3202 Resetting This returns the transmitter settings to their factory defaults. 1. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button. UTILITIES 2. Press the UP/DOWN button to select [RESET] and press the SET button. RESET No 3. Press the UP/DOWN button to select [Yes]. 4. When the confirmation screen is shown, press the UP/DOWN button again to select [Yes]. 5. Press the SET button. • Reset starts.
How to attach the transmitter (ATW-T3201) The ATW-T3201 transmitter is equipped with a clip that can be used to attach the transmitter to a belt, etc. You can reverse the direction of the input connector by attaching the clip in the opposite direction. Pull both sides of the clip firmly to the outside to remove the clip from the product. Making connections (basic connections) This is an example of connections made when using one receiver.
Achieving stable reception Low RF signal may result if there are obstructions between receiver antennas and transmitter(s). In such a case, reposition the antennas to get better reception. Use external antennas (sold separately) if the installation space is limited. Rack-mounting the receiver • Screws for rack-mounting the receiver are not included. • Consider ventilation when rack-mounting to avoid heat building up in the rack.
Troubleshooting ATW-R3210 Symptoms Causes and countermeasures The power can't be turned on. Confirm that the AC adapter is correctly connected. There is no voice output. The voice output level is low. Confirm that the transmitter/receiver channels are correct Confirm that the power button of the receiver is not turned OFF. p. 15, p. 20 p. 13 - Confirm that all connected components, such as a mixer, are correctly connected to the receiver.
Dimensions 223.5 191.0 ATW-R3210 5.0 43.4 210.
Dimensions 82 23 ATW-T3201 64 (Unit: mm) Φ 37 ATW-T3202 193 (Unit: mm) 28
Specifications Overall system specifications Operating frequencies*1 Band Band Band Band Band Band Band Band DE2: EE1: EF1: FG1: GG1: GH2 HH2 JJ1 Frequency range 470.125 530.000 590.000 650.000 727.100 794.100 821.100 925.100 Minimum frequency step 25 kHz Modulation mode FM to to to to to to to to 529.975 589.975 649.975 699.875 786.900 805.900 831.900 937.400 Number of frequencies MHz MHz MHz MHz MHz MHz MHz, 863.100 to 864.
Specifications ATW-T3201 RF output power High: 30 mW, Low: 10 mW (switchable), at 50 ohms Spurious emissions Following federal and national regulations Input connection Four pin locking connector 1 4 2 3 Pin 1: GND Pin 3: MIC INPUT Pin 2: INST INPUT Pin 4: DC BIAS +5 V High-pass (low-freq. roll-off) 125 Hz, 12 dB/octave Batteries Two 1.5V AA, not included Battery life* High: 8.0 hours (alkaline) High: 9.0 hours (Ni-MH 1,900 mAh) Dimensions 64 mm (2.52") × 82 mm (3.22") × 23 mm (0.
Audio-Technica Corporation 2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan www.audio-technica.com ©2020 Audio-Technica Corporation Global Support Contact: www.at-globalsupport.com 232416960-02-02 ver.1 2018.04.15 ver.2 2020.03.