wireless 1800 Series Camera-mount UHF Wireless Microphone Systems (single-channel) wireless wireless wireless wireless ATW-1811 UniPak® Body-pack Transmitter System ATW-1812 Plug -on Transmitter System ATW-1813 Plug-on and Body-pack Transmitter System Set-up and Operation
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This device complies with INDUSTRY CANADA R.S.S. 210, en conformité avec IC: RSS-210/CNR210. Operation is subject to the following conditions: 1) This device may not cause harmful interference and 2) this device must accept any interference received, including interference which may cause undesired operation.
1800 Series Components (single-channel) Receiver and Included Components/Accessories ATW-R1810 Single-channel receiver Two detachable antennas 18" output cable, TA3F to XLRM Pouch with belt clip (holds receiver) Note: All model numbers have an additional letter at the end to indicate frequency band.
System Features (single-channel) • True Diversity operation for resistance to multi-path interference and dropouts • UHF reception with 996 frequencies selectable in 25 kHz steps • Automatic frequency scanning for easy selection of open channels • Tone Lock™ squelch system eliminates interference when transmitter is off • Balanced output on receiver allows connection to a balanced microphone-level input on camera, mixer or amplifier • Headphone monitor output with independent level control
Quick Overview of System Operation Thank you for purchasing this Audio-Technica 1800 Series Single-channel Camera-mount UHF Wireless Microphone System. All 1800 Series Single-channel systems are designed primarily to be used with video cameras, with the ATW-R1810 Receiver mounted on a camera and connected to the camera's audio input; they may also be used with other components equipped with microphone-level input. First, insert batteries. (See Receiver Battery Installation, page 8.
ATW-R1810 Single-channel Receiver Controls (front panel) 2 6 1 3 5 2 4 LCD 1 Liquid Crystal Display shows battery status and frequency settings. Antenna Input Jacks 2 BNC-type antenna connectors. Attach the antennas to the antenna input jacks. Make certain that during operation there is a clear open-air path between the receiver antennas and the transmitters.
(rear panel) 7 10 8 9 11 PIN 1 Balanced Audio Output Jack: TA3M-type connector. Pin 1: ground (shield); Pin 2: “audio +”; 7 Output Pin 3: “audio –”. A standard 2-conductor shielded cable can be used to connect the receiver output to a balanced microphone-level input on a camera, mixer or integrated amplifier. Controls the output level of the receiver. Turn clockwise to increase output level.
ATW-R1810 Single-channel Receiver Batteries Battery Selection Each ATW-R1810 Single-channel Receiver uses four 1.5V AA batteries, not included. Alkaline type is recommended. Always replace all batteries. Make certain the receiver power is Off before replacing batteries. Note: The ATW-R1810 receiver also functions without batteries if connected to an external power supply (12V DC source, 500 mA nominal current, not included). Battery Installation 1.
Operating the Receiver NOTE: Transmitter-Receiver pairs must be set to identical frequencies. Overview… Selecting Frequencies 1. To turn the receiver on, press and hold the Power/Set button until the Power LED lights, and on your Receiver the LCD window comes on (about 2-3 seconds). The operating frequency will show in the window after the power-up sequence. 2. Press the Power/Set button to enter the Frequency Selection Menu mode; the word “MENU” will appear in the upper left corner of the LCD window. 3.
ATW-T1801 UniPak® Body-pack & ATW-T1802 Plug-on Transmitter Controls 1 5 2 4 6 7 POWER MUTE SET 12 8 11 10 3 7 SET 8 POWER/MUTE 9 ATW-T1801 UHF TRANSMITTER 3 2 6 11 Antenna 1 The ATW-T1801 UniPak® body-pack transmitter includes a field-replaceable flexible antenna. For best results, allow the antenna to hang freely and full length from the bottom of the transmitter. If the received signal is marginal, experiment with different transmitter positions or try repositioning the receiver.
Transmitter Batteries ATW-T1801 ATW-T1802 Each transmitter uses two 1.5V AA batteries, not included. Alkaline type is recommended. Battery Selection Always replace both batteries. Make certain the transmitter power is Off before replacing batteries. 1. Open the battery compartment door by sliding the catch down (on body-pack) or pushing in Transmitter Battery direction of arrow (on plug-on transmitter). Installation 2.
Transmitter Functions Function Menu Frequency Default Setting Lowest in band RF Power Audio Input Level RF LOW +6 dB Power/Mute Locks NO.LOC Input Select** Reset to Defaults MIC PRESET Quit QUIT Choices (Edit) 996 frequencies (25 kHz steps) RF LOW, RF HI - 6 dB, 0 dB, +6 dB, +12 dB, +18 NO.LOC, ALL.LOC, MUT.LOC, PWR.
Operating the Transmitter (continued) 1. A “PRESET” selection in the menu allows you to reset all transmitter functions to their Restore Default Settings factory-default values. 2. Press the Set button once to move to Menu mode. 3. Press the Up arrow twice to move to “PRESET” in the LCD window. 4. Press the Set button once and “LOAD” will appear in the LCD. 5. Press and hold the Set button until “DEF” appears in the LCD. 6. Press and hold the Set button until “LOADED” appears briefly in the LCD.
Available Accessories Cardioid condenser lavalier microphone Wireless Essentials ® Microphones and Cables AT829cW Omnidirectional condenser lavalier microphone (all Wireless Essentials accessories are MT830cW terminated for use with UniPak® transmitters) MT830cW-TH “Theater” model, same as MT830cW except beige-color mic and cable AT831cW Cardioid condenser lavalier microphone AT889cW Headworn noise-cancelling condenser microphone AT892cW MicroSet ® headworn omnidirectional condenser microphone AT892cW-C
Specifications† UHF Operating Frequencies Band C: Band D: Number of Operating Frequencies Frequency Stability Modulation Mode Normal Deviation Operating Range Operating Temperature Range Frequency Response Overall System 541.500 to 566.375 MHz 655.500 to 680.375 MHz 996 total per band (25 kHz increments) ±0.
One -Year Limited Warranty Audio-Technica professional wireless systems purchased in the U.S.A. are warranted for one year from date of purchase by Audio-Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to A.T.U.S.