2000 Series Frequency-agile True Diversity UHF Wireless System Installation and Operation
2000 Series Installation and Operation Such modifications could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This device complies with INDUSTRY CANADA R.S.S. 210, en conformité avec IC: RSS-210/CNR210.
2000 Series Installation and Operation Series transmitters and receivers must be used together and should not be used with components from other Audio-Technica wireless systems, or with those of other manufacturers. Please note that in multiple-system applications there must be a transmitter-receiver combination set to a separate channel (frequency) for each input desired (only one transmitter for each receiver).
2000 Series Installation and Operation Receiver Controls and Functions Fig. B – Front Panel Controls and Functions 1 2 3 4 1. POWER SWITCH: Press the Power switch in to turn the receiver on. The LCD window will light, and the operating channel number will be displayed in the window. To turn the receiver off, press the Power switch again. 5 Fig. C – Receiver LCD Window Display 2. LCD WINDOW: Liquid Crystal Display indicates channel setting and operational readings. See Fig. C for examples. 3.
2000 Series Installation and Operation Fig. D – Rear Panel Controls and Functions 15 10 10. ANTENNA INPUT JACK: BNC-type antenna connector for Tuner “B.” Attach the antenna directly, or extend it with a low-loss antenna cable. See the “Antennas” section on page 3 for more details. 11. ANTENNA POWER SWITCH: Two-position switch turns on/off the 12V AC antenna power for use with powered antennas or accessories. Factory setting is off. See the “Antennas” section on page 3 for more details.
2000 Series Installation and Operation Transmitter Controls and Functions Battery Selection Two 1.5V AA alkaline batteries or rechargeable AA NiMH batteries for use with Audio-Technica’s ATW-CHG2 Recharging Station are recommended. UniPak® Transmitter Battery Installation 1. Open the transmitter door by pressing gently on the side-cover indentations and pulling back the hinged cover. 2. Lift the battery-keeper arm, and carefully insert two fresh 1.
2000 Series Installation and Operation System Operation Switch on the receiver. Do not switch on the transmitter yet. Receiver On… The LCD display will light up and one of the tuner operation indicator LCD segments (A or B) will light, even though the transmitter is not on. If two or more of the RF LCD segments light up at this point, there may be RF interference in the area. If this occurs, change operating channels (select another frequency).
2000 Series Installation and Operation Setting Levels (Continued) ATW-T210a UniPak® Transmitter Trimmer adjustments in the UniPak® transmitter (Fig. E ) will enable you to use microphones or instruments with different output levels. Fig. E – UniPak® Transmitter Open 1. For MIC: Set microphone level trim control fully clockwise (maximum) and instrument level trim control fully counterclockwise (minimum). Factory setting is fully clockwise (maximum).
2000 Series Installation and Operation Specifications† Overall System UHF Operating Frequencies Frequency Range Band D: 656.125 to 678.500 MHz Band E: 800.550 to 813.150 MHz Band F: 854.900 to 864.900 MHz Band G: 722.125 to 744.500 MHz Band I : 487.125 to 506.500 MHz Number of Channels 10 10 10 10 10 Not all frequencies are available in all areas. Please check with local regulations.
2000 Series Installation and Operation 2000 Series Frequency Channel Plan Band D Channel 1 2 3 4 5 6 7 8 9 10 Frequency-MHz 656 . 125 659 . 375 660 . 000 662 . 125 665 . 125 669 . 750 671 . 500 677 . 000 678 . 125 678 . 500 Band E Channel 1 2 3 4 5 6 7 8 9 10 Frequency-MHz 800 . 225 802 . 775 804 . 000 804 . 700 805 . 900 806 . 300 813 . 100 813 . 900 815 . 000 818 . 025 Band F Channel 1 2 3 4 5 6 7 8 9 10 Frequency-MHz 863 . 100 863 . 500 864 . 100 864 . 900 854 . 900 855 . 275 855 . 900 856 .
Stetement of Compliance
To reduce the environmental impact of a multi-language printed document, product information is available online at www.audio-technica.com in a selection of languages. Afin de réduire l’impact sur l’environnement de l’impression de plusieurs, les informations concernant les produits sont disponibles sur le site www.audio-technica.com dans une large sélection de langue.