TM ACCESS/A AUDIO CONTROL SYSTEM MODEL: A711 L-Series Installation Manual TiL Document No. 09RE416 Rev. A May, 2012 Technisonic Industries Limited 240 Traders Boulevard, Mississauga, Ontario L4Z 1W7 www.til.ca Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A REVISIONS Revision A A A Page 2-11 2-19 2-20 Description Fig. 2-9 Updated for PA Pin corrections Installation drawing corrected for PA pins Fig. 2-13 Connector Map corrected for PA Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A CAUTION This unit contains static sensitive devices. Wear a grounded wrist strap and work at a static-safe workstation when handling internal printed circuit boards. WARRANTY INFORMATION The Model A711L Audio Controller is under warranty for one year from date of purchase.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A TABLE OF CONTENTS TiL DOCUMENT 09RE416 SECTION 1 GENERAL DESCRIPTION 1.1 1.2 1.3 1.4 1.5 1.6 Introduction ................................................................................................................. 1-1 Description .................................................................................................................. 1-1 Purpose of Equipment ......................................................................
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A LIST OF TABLES 1-1 A711L General Specifications .......................................................................................... 1-4 LIST OF ILLUSTRATIONS 1-1 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 A711L Audio Control - General View................................................................................ 1-3 A711L Outline Drawing .......................................................................................
SECTION 1 GENERAL DESCRIPTION 1.1 INTRODUCTION This publication provides operating and installation information on the Model A711 L-series, ACCESS/A Audio Controls manufactured by Technisonic Industries Limited. For convenience, it is referred to as the “A711L” in the manual. This unit is designed to provide high performance cockpit audio control in high noise installations.
ACCESS/A A711 L-Series Installation Manual 1.3 09RE416 REV. A PURPOSE OF THE EQUIPMENT The A711L ACCESS/A Audio Controls are designed to provide centralized audio management and control within an airborne communications environment. This includes radio and transceiver selection, intercom, airframe threat alerting, and crew management. These units have been packaged to minimize size and weight characteristics and are ideally suited for helicopter installations, or any other Dzus rail panel location.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A FIGURE 1-2 A711L ACCESS/A AUDIO CONTROLLER - GENERAL VIEW Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 1.5 09RE416 REV. A TECHNICAL SUMMARY A summary of the relevant electrical, operational, mechanical and physical characteristics of the control panels are given in Table 1-1, General Specifications. TABLE 1-1 A711 L-Series GENERAL SPECIFICATIONS MODEL A711L-Series - ACCESS/A Audio Controller: PHYSICAL CHARACTERISTICS: Width (max.)..........................................................................................................................5.
ACCESS/A A711 L-Series Installation Manual 1.6.1 09RE416 REV. A Power Limitations With Standard Set-up, which consists of six headsets connected, a power output of not less than 332 mW is delivered per headset (as represented by 150 ohms) provided that the Direct Alert Input is terminated in not less than 600 ohms and that nominal input voltages are applied at the applicable channel inputs. Nominal microphone input: 100 mVrms; Nominal Communications/Navigational Input: 5.5 Vrms. 1.6.
ACCESS/A A711 L-Series Installation Manual 1.6.4 09RE416 REV. A Isolation Limitations When in Pilot Isolation Mode, the pilot microphone for ICS operation is rendered inactive. Consequently, neither co-pilot nor passengers can receive pilot intercom transmissions while the latter is in Isolation mode. 1.6.5 Standard Settings Utilised Throughout Testing Pilot Headset Settings utilized throughout testing was for the standard 150 ohms impedance headset.
SECTION 2 INSTALLATION INSTRUCTIONS 2.1 GENERAL This section contains information and instructions for the correct installation of the A711 L-Series, ACCESS/A Audio Controllers. For convenience they are referred to as A711L in the manual. Make certain that the unit is correctly operating in accordance with the equipment user's requirements and manufacturer’s specifications, prior to releasing the equipment for service. 2.
ACCESS/A A711 L-Series Installation Manual 2.4 09RE416 REV. A ACCESS/A AUDIO PANEL INSTALLATION The A711L ACCESS/A Audio Controls are designed to be Dzus mounted and should be installed in conjunction with an IN-A711L installation connector kit. See Figure 2-1 for an outline drawing of the units with dimensions, to facilitate the installation. CABLE CLEARANCE: Allow at least 2.5” of additional rear clearance for mating connectors and hoods (side routing), or 3.0” (back routing).
ACCESS/A A711 L-Series Installation Manual FIGURE 2-1 Technisonic Industries ltd. 09RE416 REV.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-2 PILOT/CO-PILOT WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-3 COM1-COM4 WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-4 COM5-NAV1 WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-5 NAV2-NAV5 WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-6 NAV6-NAV8 / CST / MUSIC WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-7 PASSENGER WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-8 ALTERNATE PASSENGER WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-9 POWER & ALERTING WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-10 DIRECT INPUT/SPECIAL FUNCTION WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-11 RESERVED WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-12 SPECIAL 6-PLACE PASSENGER WIRING Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 2.4.1 09RE416 REV. A PASSENGER HEADSET CONSIDERATIONS The A711L has the ability to drive passenger ICS in both PTT or VOX modes, but you must consider this: Loose passenger headsets lying in the cabin MUST be properly accounted for. If the headsets are wired in directly, the loose headsets will be a continual source of intercom noise, rattling around the cabin.
ACCESS/A A711 L-Series Installation Manual 2.6 09RE416 REV. A INSTALLATION - PIN LOCATIONS AND CONNECTIONS The pin numbers and locations for the connectors located on the rear of the A711L ACCESS/A Audio Control are shown in the following tables.
ACCESS/A A711 L-Series Installation Manual Top Connector J201 DC37P 09RE416 REV.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Mating Cable Connector: DA15S Bottom Connector J102 DA15P (15 Pin Female) J102 Low 9 3 High 1 2 11 4 5 6 Connector Pin Assignments Connection Alert Audio Input (Internal Jumper Selection) PA Key Output (Active Low) PA Mic Out (Note: Rev.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Figure 2-13 Full A711L Connector Map (view from mating connector wiring side) 2.7 HEADPHONE INSTALLATION The A711L ACCESS/A Audio Controls are intended for use with industry standard 150/600 ohm headphones. There is also provision for connection to an 8 ohm (minimum impedance) speaker, for a supplemental cabin speaker output.
ACCESS/A A711 L-Series Installation Manual 2.8 09RE416 REV. A MICROPHONE INSTALLATION All microphone connections to the A711L must be done with shielded cables. The inputs are intended for use with standard “carbon-equivalent” or amplified dynamic Microphones (such as the D/C M1, M4 M7, etc.).
ACCESS/A A711 L-Series Installation Manual 2.12 09RE416 REV. A ANNUNCIATOR DIMMING The lighted annunciators (Radio Selected, TX status) can be operated in three ways. First, they can be run at their fixed intensity at all times, this is done by jumpering J102 Pin 6 (Day/Night Dim I/P) to J101 Pin 17 (28V Input Power). No connection is then made to J101 Pin 2 (Auto Dim Input).
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Rear Tone Alerts Adjustments Side RX/TX Adjustments Side Lighting/CST/Aux Adjustments Top PA Adjustments 2.14 Technisonic Industries ltd.
ACCESS/A A711 L-Series Installation Manual 2.15 09RE416 REV. A POST-INSTALLATION ADJUSTMENTS After installation, the A711L may require adjustment of some functions to compensate for airframe and equipment specific issues, and to suit user tastes. Locations of these adjustments are as shown in section 2.14. All are 20-turn miniature trimpots, except as noted. “MUSIC” input may be for any entertainment audio feed, such as CD, tuner, etc.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A J201 (above) may be removed to make these adjustments Back - Alerting Adjustments Adjustment Name Alert Level Location Back 1 / 2 Tone Back 1 / 2 Rate Back 3 Tone Back Procedure/purpose Adj. for comfortable alert level, controls both direct input (option) and tone generator Adj. for closest Alert 1 and Alert 2 tone match to existing alert horn sound. Adj. for closest Alert 2 pulse rate match to existing alert horn sound. Adj.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Side Lighting/CST/Aux Adjustments Adjustment Name Location Procedure/purpose Notes ICS Low Cut R/H Side Not normally a field setting. CST/MUSIC/AUX Hi Cut R/H Side CST/MUSIC/AUX Low Cut CST/MUSIC/AUX Mute Depth R/H Side CST/MUSIC/AUX Volume R/H Side Backlight Dimming R/H Side Backlight Intensity Range R/H Side TX Indicator Brightness R/H Side Sets low frequency cut-off (BASS) of ICS audio.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A Side RX/TX Adjustments Adjustment Name RX Mute Depth Location L/H Side Upper Procedure/purpose Sets mute level of RX audio during TX operations. (Sidetone) RX Hi Cut L/H Side Upper L/H Side Upper L/H Side Upper L/H Side Upper Sets high frequency cut-off (TREBLE) of RX audio. Sets low frequency cut-off (BASS) of RX audio. Sets Mute depth of ICS audio during TX operations Sets hi frequency cut-off (TREBLE) of ICS audio.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV.
ACCESS/A A711 L-Series Installation Manual 09RE416 REV. A 2.16 Product Warranty Terms Technisonic Industries Limited 240 Traders Blvd., Mississauga, ON Canada L4Z 1W7 Tel: (905) 890-2113 Fax: (905) 890-5338 IMPORTANT! PRODUCT WARRANTY All communication equipment manufactured by Technisonic Industries Limited is warranted to be free of defects in Material or Workmanship under normal use for a period of one year from Date of Purchase by the end user.