English Congratulations! Thank you for purchasing an Audiopipe amplifier for your car audio system. Now you own an amplifier of uncompromising design and engineering incorporating the latest advanced circuit technology. You will discover soon that our amplifiers display optimum sound with high quality, reliable performance. Audiopipe amplifiers are adopted by advanced craftsmanship which using the highest quality components and strict quality control system. In order to provide you the best performance.
English APSM-1300/APSM-1500 1 15 14 6 7 2 9 8 5 -1- 10 3 4 11 13 12
APSM-2000 1 15 14 6 7 2 9 8 5 -2- 3 10 4 11 13 12
1 Speaker connection Never connect the speaker cables with the chassis ground. This may destroy your amplifier. Check that your speakers are connected correctly which means plus to plus and minus to minus. We recommend speaker cable from 2.25 mm to up. The connection ways are shown in the attachment. 2 BATT+ Battery + terminal. The +12 Volt power cable must be connected with a fuse in line near the battery + terminal. Please see the table of cable and fuse selection. 3 REM Remote terminal.
English 10 Low Pass Filter Filter out high frequency that the woofer cannot play. Adjust this knob to match the woofer's frequency response. 11 SUBSONIC Filter out unwanted too low frequency. This function will increase the power handing of your woofer’s. It can adjust the frequency filter from, 10Hz (OFF) to 50Hz. 12 Bass boost Level Adjust the boosted frequency from 0 ~ 12dB, APSM-1300/APSM-1500’s boosted frequency is is adjustable. 13 Bass boost Frequency Adjust the boosted center frequency.
English We recommend you have the installation done by an Authorized Audiopipe Dealer. Required power, ground wire and proper external fuse as below: Model APSM-1300 APSM-1500 APSM-2000 Fuse 80 AMP 100 AMP 150 AMP Wire 4 Gauge 2 to 4 Gauge 0 to 2 Gauge We recommend the fuse should be installed no more than 12 inches from the battery. The ground wire should be connected directly with the chassis of your vehicle which should be metal to metal ground point connection.
English ONE SPEAKER MONO APSM-1300/APSM-1500 -6-
English ONE SPEAKER MONO APSM-2000 -7-
English TWO SPEAKER MONO APSM-1300/APSM-1500 -8-
English TWO AMPLIFIERS LINKED TO ONE CHANNEL APSM-1300/APSM-1500 -9-
English English TWO AMPLIFIERS LINKED TO ONE CHANNEL APSM-2000 - 10 -
English Problem Run indicator doesn’t light up. Solution • Check all fuses on the amplifier. • Check main fuse near the battery. • Check plus and minus battery cables. • Check remote voltage. Problem Run indicator is on but no sound. Solution • Check volume control on the radio. • Check GAIN regulator on the amplifier. • Check RCA cables and connections. • Check speaker cables and connections. Problem Bass response is low. Solution • One speaker cable could be disconnected the bass.
APSM-1300 RMS @ 4 Ohm (<1% DISTORTION) ....................................... 400W RMS @ 2 Ohm (<1% DISTORTION) ....................................... 600W RMS @ 1 Ohm (<1% DISTORTION) ....................................... 1000W Input Level ................................................................................ 0.2 ~ 5V Frequency Response ............................................................... 8 ~ 180Hz LPF ................................................................................
English APSM-2000 RMS @ 4 Ohm (<1% DISTORTION) ....................................... 900W RMS @ 2 Ohm (<1% DISTORTION) ....................................... 1400W RMS @ 1 Ohm (<1% DISTORTION) ....................................... 2000W Input Level ................................................................................ 0.2 ~ 5V Frequency Response ............................................................... 8 ~ 180Hz LPF ......................................................................
English INTRODUCCION Felicidades! Gracias por comprar el amplificador AUDIOPIPE para el sistema de audio de su auto. Ahora usted posee un amplificador de diseño inflexible y fabricación que incorpora lo mas avanzado y nuevo de la tecnología de circuitos. Pronto descubrirá que nuestro amplificador posee un sonido óptimo de alta calidad y rendimiento confiable.
English APSM-1300/APSM-1500 1 2 3 4 +12V REM GND SPEAKER 1Ω MIN 15 14 6 7 9 8 5 -1- 10 11 13 12
APSM-2000 1 15 14 6 7 2 9 8 5 -2- 3 10 4 11 13 12
1 Conexiones de las bocinas Nunca conecte los cables de las bocinas con el chassis a tierra. Esto puede destruir su amplificador. Verifique que sus bocinas estan conectadas correctamente. Lo que signifca “mas a mas” y “menos a menos”. Recomendamos un cable para las bocinas desde 2.2 mm hacia arriba. Las vias de conexión se muestran en el anexo. 2 BATERIA + El terminal + de la bateria y el cable de potencia de 12V deben ser conectados con un fusible en linea cerca del terminal + de la batería.
9 Puente de Salida Esta salida RCA envia señales via Puente a otro amplificador clase “D” en configuración de Puente. 10 Filtro de Paso Bajo Es un filtro de salida de alta frecuencia donde el woofer no puede reproducir. Ajuste este botón para igualar la respuesta de frecuencia del woofer. 11 SUBSONICO El filtro hacia afuera no es deseado por su baja frecuencia. Esta función incrementará la potencia de su woofer. Se puede ajustar la frecuencia del filtro desde 10Hz (OFF) hasta 50Hz.
INSTALACIÓN Recomendamos que la instalación sea realizada por un concesionario Audiopipe autorizado. Voltaje requerido, cable a tierra y fusibles externo apropiado, como se muestra debajo: Modelo APSM-1300 APSM-1500 APSM-2000 Fusible 80 AMP 100 AMP 150 AMP Cable Calibre 4 Calibre 2 a 4 Calibre 0 a 2 Recomendamos que instale el fusible a no mas de 12 pulgadas de la baterÌa.
CONFIGURACION DEL CABLEADO UNA BOCINA MONO APSM-1300/APSM-1500 -6-
UNA BOCINA MONO APSM-2000 -7-
DOS BOCINAS MONO APSM-1300/APSM-1500 -8-
DOS AMPLIFICADORES CONECTADOS A UN CANAL APSM-1300/APSM-1500 -9-
DOS AMPLIFICADORES CONECTADOS A UN CANAL APSM-2000 - 10 -
Problema El Indicador de Encendido no se enciende. Solución • Verifique todos los fusibles en el amplificador. • Verifique el fusible principal cercano a la batería. • Verifique los cables + y – de la batería. • Verifique el voltaje del remoto. Problema El indicador de encendido está funcionado pero no existe sonido. Solución • Compruebe el control de volumen del radio. • Compruebe el regulador de GANANCIA en el amplificador. • Compruebe los cables RCA y las conexiones.
APSM-1300 RMS a 4 Ohm (<1% de distorción) .......................................... 400W RMS a 2 Ohm (<1% de distorción) .......................................... 600W RMS a 1 Ohm (<1% de distorción) .......................................... 1000W Nivel de Entrada ...................................................................... 0.2 ~ 5V Respuesta de Frecuencia ........................................................ 8 ~ 180Hz LPF .....................................................................
APSM-2000 RMS a 4 Ohm (<1% de distorción) .......................................... 900W RMS a 2 Ohm (<1% de distorción) .......................................... 1400W RMS a 1 Ohm (<1% de distorción) .......................................... 2000W Nivel de Entrada ...................................................................... 0.2 ~ 5V Respuesta de Frecuencia ........................................................ 8 ~ 180Hz LPF ....................................................................