LEVITON INTEGRATED NETWORKS Installation Manual for Residential Installation Manual for Residential Structured Wiring www.leviton.com/lin www.levitonvoicedata.com Tech Line: 800-722-2082 Customer Service: 800-323-8920 W-818/E1-35M rs E-1 Structured Wiring Version 2.
INSTALLATION MANUAL FOR RESIDENTIAL STRUCTURED WIRING This manual provides a comprehensive description of issues related to the fast evolving subject known as residential structured wiring. It covers industry standards, warranties, installer certification, ordinances, tools, job planning, system design and installation techniques.
TABLE OF CONTENTS Section Page No. 1 Introduction to Leviton Integrated Networks Systems 1.1 Structured Media Subsystems ........................................................................................................................ 1-2 1.2 Types of Structured Media Subsystems.......................................................................................................... 1.2.1 Essential Infrastructure ......................................................................................
6.3 Enhanced Infrastructure Platform ................................................................................................................. 6.3.1 Series 420 SMC .................................................................................................................................. 6.3.2 Media Versatile Panel.......................................................................................................................... 6.3.3 Wallplates, Jacks and Connections ...................
Installation Manual 8 Pre-Wire Installation 8.1 The Walk-Through ......................................................................................................................................... 8-1 8.1.1 The Reality of the Job and the Installation.......................................................................................... 8-1 8.2 Mud Rings ..................................................................................................................................................
9.5 Multi-Location Networking............................................................................................................................. 9-8 9.5.1 Video Distribution (Coaxial)................................................................................................................. 9-11 9.6 Multi-Room Stereo Sound Application .......................................................................................................... 9.6.1 Multi-Room Considerations .....................
INTRODUCTION 1 INTRODUCTION to Leviton Integrated Networks and Structured Media Systems 1 Introduction to Leviton Integrated Networks and Structured Media™ systems Leviton Integrated Networks purpose. More than ever, today’s technologies are confronting homeowners with an expanded range of choices—and some hard decisions as a result.
1 INTRODUCTION to Leviton Integrated Networks and Structured Media Systems Leviton Integrated Networks presents these most desired home features in pre-configured subsystem packages, with system design, component placement, wiring and installation outlined in easily-followed steps.
WARRANTY 2 Leviton Quality and Warranty Quality Statement “It is our policy to continuously improve the quality of our management systems in order to achieve total customer satisfaction and assure the overall safety, reliability, and performance of our products.
CERTIFICATION 3 Certification Policy All details for this program are covered in Leviton’s “Guidelines for Certification Program Partners”. The certification program will help you install the Leviton Integrated Network platforms and application subsystems according to best practices and will enable the homeowner to receive years of problem free service from the completed installation.
ORDINANCES 4 Local Ordinances, Covenants, and Service Provider Coordination Local Ordinances Local ordinances require adherence to national and local electrical codes when installing AC and, in many instances, low voltage wiring and devices. Make sure you follow all local ordinances and codes when installing a Leviton Integrated Networks system. For example, this manual refers to the use of mud rings instead of electrical boxes for wallplate locations.
IMPORTANT SAFETY AND INSTALLATION INFORMATION FOR ALL TELECOMMUNICATIONS APPLICATIONS There are special safety considerations with telephone wiring that may be unknown by workers new to this field. The following hints and guidelines should be followed closely to help avoid safety hazards, and ensure trouble-free installations and highquality telephone service. This publication cannot, however, cover every aspect of safe installation and connection of telephone wiring.
Installation Manual signal level of 0 dBmV to 15 dBmV. The signal level at the demarcation point will dictate whether a video amplifier is required prior to video splitters. If CATV is available, check to see if cable modems are available for high-speed internet access. Some cable modem providers want a direct run from the CATV demarcation point to the location of the cable modem.
5 ACCESSORIES Recommended Accessories, Tools, and Test Equipment ACCESSORIES 5 Recommended Accessories, Tools, and Test Equipment An installer with the highest skill level can’t make up for inferior equipment or tools. The old adage about using the right tools for the job certainly applies to installing the structured cable and components that make up modern day data, telephone, and media networks.
Installation Manual Installer’s Tip: An insulated staple is an ideal fastener for low-voltage wiring. The insulation acts as a built-in stop that prevents the staple from crushing or stressing the cables. Be sure the cable diameter does not exceed the staple’s capacity.
• Made of heavy duty 12 gauge cold rolled steel with 6roller design to pull cables smoothly and easily. 5 ACCESSORIES Recommended Accessories, Tools, and Test Equipment • Opens simply and closes securely with quickrelease pin. Cable Joe® Application and Use Tape (electrical and other) Cable Joe™ Permanent marker Flashlight Ladder Broom and dust pan Position Cable Joe so that cables run at the widest angle possible. This will preserve cable bend radius. 5.
Installation Manual The Wire Punchdown Termination Tool presses wire conductors into place in Insulation Displacement Connectors (IDCs) and in QuickPort modular snap-in jacks. It will also trim off the ends of the wire conductors. The Wire Using Wire Punchdown Punchdown/Termination Termination Tool on Leviton Cat 5 or 5e jack Tool assures solid connections on an array of wire termination blocks.
When field-testing Category 5 or 5e cable installed for data transmission: 5 ACCESSORIES Recommended Accessories, Tools, and Test Equipment • Use a Category 5 or 5e field test set, following the manufacturer’s instructions • Use a Category 5 or 5e field test set for testing all Category 5 or 5e cable, respectively, installed for data transmission. Select a test set from one of the listed, or other reputable manufacturer and follow the manufacturer’s instructions.
Installation Manual The low-cost Tone Test Set can test for all types of wire applications including telephone, data, CATV, HVAC systems, and security/fire alarms. Results are shown on an easy-to-read LED display. Telco standard 6A-type alligator clips with piercing pins securely grip 66-clips, screw heads, screw bodies, and wire-wrapped of threaded terminals, allowing testing of all types of configurations. A 6-position, 2-conductor plug lead is also provided for connection to modular jacks.
DESCRIPTION 6 Description of the Leviton Integrated Networks Structured MediaTM System 6 DESCRIPTION of Leviton Integrated Systems The Leviton Integrated Networks are composed of a series of smaller subsystems. This manual explains the installation of the Structured Media subsystem as described in Section 1. The Structured Media subsystem covers all of your customer’s data, telephone, and entertainment needs.
Installation Manual • Category 5 Voice and Data Module whose six Category 5 or 5e ports allow for basic home networking (data, phone, fax or modem) and can be connected to a Telephone Distribution Module, key system, or network hub • 1X6 Video Splitter that is suitable for both cable TV and off-air antenna signals ✍ Take Note: Both the Bridged Telephone Module and the Category 5 Voice and Data Module are available as standalone units and can be used for expansion or special applications, when properly mou
Installer’s Tip: Think of a SMC the same way you would a service entrance. A 200-amp panel allows for plenty of future expansion of an electrical service whereas a 150-amp panel that meets a customer’s immediate needs might not. Although additional Series 140 subsystems can be added as demand for structured wiring increases, you might be better off installing the larger Series 280 or 420 at the outset.
Installation Manual 6.3 Enhanced Infrastructure Platform An enhanced infrastructure for a four-bedroom home would include the following components in a SMC 420: • Coax surge protector (P/N 47690-6S) • AC Power Module (P/N 47605-DP) Larger homes or customers with greater structured cabling needs require larger SMC capacity.
6.3.3 Wallplates, Jacks, and Connections The variety of terminating connectors, jacks, and wallplates, the small, but critical components of any system infrastructure, will be discussed in section 8. You have a choice of 1, 2, 3, 4, or even 6 position QuickPort or Decora style wallplates along with Category 5 or 5e jack, F-Connector, audio binding post, and blank snap-in inserts. You can order the wallplates and snap-in inserts in white, almond, or ivory colors.
Installation Manual • Sends video to up to eight televisions within the home • Amplifies incoming signals • Provides two auxilliary inputs and combines them with the internal 8-way splitter; Requires a modulated signal with 20-30 dB signal strength such as Leviton’s SMC Modulator (P/N 48213-VMA) • Distributes CATV or terrestrial antenna signals out to eight locations with no loss • Includes two DSS antenna inputs passed through to two outputs to DSS receivers 6.
The DC Power Distribution Module features: • 12 outputs that provide 12 Vdc power for up to 12 devices • F-connector output for the 3 X 8 Bi-Directional Video Module • Low-profile, flush-mount design of the target • Six removable double screw terminal jacks with slot drive screws • Two signal connections and two power connections Module DESCRIPTION of Leviton Integrated Systems Power Consumption (mA) 3 X 8 Bi-Directional Video Module 80 Decora Media System 60 Decora Camera 70 Outdoor Camera 22
Installation Manual • Data collision and jabber handling functions • 10 Mps performance speed • Five Category 5 or 5e RJ-45 ports, including one port for expansion ing posts for customer stereo speaker terminations are also included. This application features: • IEEE 802.
rocker switch. The volume control unit mounts inside a standard wall box or low-voltage mud ring and connects to the Interface Module inside the Structured Media Center with Category 5 or 5e cable.
Installation Manual The outdoor camera has the same features except it also includes an audio signal (carried over the Category 5 or 5e cable) and a pan adjustment (the whole case is adjustable). 6.8.1. Video Sequencer Leviton’s Video Sequencer allows the user to monitor up to four Decora Cameras (both indoor and outdoor) simultaneously in any combination.
SYSTEM DESIGN 7 System Design and Placement—Laying Out the Basics In years past, low-voltage cable and wiring meant telephone lines, intercom systems, and door chimes. Structured wiring today means ethernet connections, multiple phone and dedicated data lines, multi-location stereo, and more. It’s increasingly important to carefully design your system and write up a plan for cable, device, and distribution center placement. With the median size of newly constructed homes in the U.S.
DECORA CAMERA IR TARGET DEVICE KEY: DATA VIDEO TELEPHONE WALLPLATE KEY: OPTIONAL MEDIA ROOM SHOP TWO CAR GARAGE DEN POWDER LAUNDRY FAMILY ROOM ENHANCED STRUCTURED MEDIA PLATFORM - 1ST FLOOR (TYPICAL) 7 SYSTEM DESIGN System Design and PlacementLaying Out the Basics For more information call your Leviton representative or the Leviton Technical Hotline at 800-722-2082 © Copyright 2001 Leviton Manufacturing Co., Inc.
DECORA CAMERA IR TARGET DATA FAMILY BATH BEDROOM FOUR BEDROOM THREE BEDROOM TWO BONUS ROOM DEVICE KEY: VIDEO TELEPHONE WALLPLATE KEY: MASTER SUITE MASTER BATH WALK-IN CLOSET SYSTEM DESIGN System Design and PlacementLaying Out the Basics ENHANCED STRUCTURED MEDIA PLATFORM - 2ND FLOOR (TYPICAL) 7 7-3 For more information call your Leviton representative or the Leviton Technical Hotline at 800-722-2082 © Copyright 2001 Leviton Manufacturing Co., Inc.
Connection Planner QuickPort connectors Voice Room type & applications Leviton part numbers Total Req’d.
(continued from previous page) Room type & applications Other location-based components 8-inch 8-inch Speakers Speaker Leviton part 40890-WP 40890-WS numbers pair single Total Req’d. 6 Number of locations planned 6.5-inch Outdoor Weather Analog Vol. Speakers Speaker Cover Control 40841-D* 40891-W 40827 Impedance pair single 5977-GY Matching 1 1 2 1 Digital Vol. Decora DMS Send DMS Other Decora Outdoor Control Media Sys. Unit Rec.
Connection Planner (continued) QuickPort connectors Voice Room type & applications Leviton part numbers Total Req’d.
(continued from previous page) Room type & applications QuickPort platform Flush-mount Wallplates Blanks Leviton part 40804-B* numbers four port 40859-B* Total Req’d. 19 26 0 Number of locations planned Other location-based components 8-inch 8-inch 6.5-inch Speakers Speaker Speakers 40890-WP pair 6 40890-WS single 1 40891-W pair 1 Outdoor Speaker 40827 single 2 Weather Analog Vol. Cover Control 40841-D* Impedance 5977-GY Matching 1 4 Digital Vol.
Installation Manual continued from page 7-1 The primary difference among the SMCs is their size: the larger the box, the more modules and panels it can hold. In addition, (the 280 and 420 series each have a surgeprotected AC power option to accommodate multiple active modules). There is virtually no limit to the size or complexity of the system you install in a normal residence. Every room can be wired for data, telephone, and multi-media.
7.4 Cabling Types and Counts for Each Location AC wiring varies by gauge size. The end use device or appliance dictates the ampacity amperage of the circuit and thus your choice of cable (14/2, 12/2, etc.). Low-voltage wiring varies by type and to a lesser extent by gauge (most will normally be 24 AWG). The TIA/EIA Standard 570-A proposes different grades of residential cabling depending on the services the cable will be providing within a residence.
Installation Manual Installer’s Tip: An audio system’s performance is determined in part by the amount of resistance in its speaker- amplifier circuit, which consists of the speaker inputs, amplifier outputs, and the wire between them. Generally, this resistance—also known as impedance—rises as the distance between the amplifier and speaker increases, and becomes a real factor in multi-room audio distribution.
Leviton offers a complete line of fiber optic terminations and patching alternatives. For more information, please contact Leviton Technical Support at (800)-722-2082. can accept 2-, 3-,4-,or 6-port inserts. The Leviton wallplates described in the following sections fit these devices: ✍Take Note: Your local code ultimately determines the • Telephone, fax, and data ports (Category 5 or 5e jacks) rules and guidelines that must be followed when installing either AC cable or low-voltage wiring.
Installation Manual 7.5.2 QuickPort™ Decora Plus™ Wallplate Inserts and Wallplates The Decora system offers the maximum in configuration flexibility, that is, they come as single-or double-gang wallplates and accommodate 2-, 3-, 4-, or 6-port inserts that secure any combination of QuickPort“ Snap-In Modules you desire. Inserts are sold separately from wallplates.
✍Take Note: Both the Essential and Enhanced platforms using the SMC 280 and 420 units incorporate an optional AC Power Module with hospital grade surge protection. This module should be wired with a dedicated 15 amp circuit. The SMC 100 and 140 do not incorporate an AC power module. TIA/EIA-570-A calls for a low-voltage distribution panel to be located within five feet of the building’s electrical ground. 7.6.2 Height Above the Floor You want your SMC at a serviceable height for most technicians.
Installation Manual • Coax cable on the right • Data and phone in the center • Audio cable on the left • AC and DC power modules on the bottom of the enclosure • Pre-Configured Structured Cabling Panels in the upper section of the enclosure All components should be installed in such a way that cable bends are sweeping and gradual rather than at right angles. The installer should employ good cable management practices to avoid twisting and kinking. 7.
PRE-WIRE 8 Installation, Labeling, and Documentation Pre-Wire Installation A walk through also allows the installer to mark off locations for mud rings and the SMC. At this point, the rough-in wiring can begin. What You’ll Need for Your Walk Through: • Your original Leviton Connection Planner The integrity of any electrical wiring system is highly dependent on the quality of its installation. Even the very best components will perform poorly if they are installed incorrectly or carelessly.
Installation Manual What You’ll Need to Install Mud Rings or Electrical Boxes: • Room locations for mud rings or boxes • Measuring tape • Small carpenter’s level control devices, or at the same level as light switches. Special locations such as built-in cabinets and shelves for home entertainment systems may require other heights. Be sure to check with your builder for any special instructions. • Screws or nails for attaching to framing members • Drill or hammer 8.
8.3.2 Mounting your SMC There are two ways to install a SMC: 1. Flush-mounting between wall studs 2.
Installation Manual 8.3.3 Grommets or Plastic Bushings 8.3.6 AC Power Module Leviton requires the installation of protective grommets or plastic bushings at every SMC knockout. Knockouts are sized for 1-inch and 1-1/2-inch conduit fittings. This protection will prevent damage to the cables as they enter the SMC. Without grommets or bushings, the insulation on the cable can tear or otherwise be compromised if it is pulled against the bare steel edge of the opening.
2. Punch out one or both of the cable entry knockouts that are also located at the bottom of the module housing and pull your cable(s) through 3. Secure your electrical cable with a standard conduit fitting or cable clamp (not included) 4. Drop the housing into its opening Next, connect the incoming power cable to the surge suppressor receptacles. the wiring connections will depend on whether one or two dedicated circuits are being run to the AC Power Module.
Installation Manual Structured Media Center Installation and Wiring Instructions Prepare Structured Media Center Plug Bushing Bushing Nut Nut Nut Nut Remove large conduit knockouts in top of Structured Media Center and install bushings for cable protection. Mount the unit between studs. Install a ground wire from the green ground screw to earth ground. Ground Wire 8.4 Structured Cabling (Pre-Wire) 8.3.8 Grounding the SMC A grounding lug can be found at the bottom of the SMC.
In the past, the main low-voltage appliance in a home was a telephone. The other was the doorbell. Known by the acronym “POTS” or Plain Old Telephone Service, this system worked well for what would now be viewed as a basic, even unsophisticated single-line analog phone service. POTS used quad wire, consisting of four individual, non-twisted wires within a single cable jacket and run in a daisy chain pattern.
Installation Manual Leviton recommends the following materials for cable installations: will surpass any lower material expense or labor cost saved by using less expensive staples. • J-hooks and similar cable supports instead of staples for supporting cable along joists • Velcro‚ tie wraps and cable straps for wrapping multiple cables and for securing cable to studs (Leviton SoftCinch‚ or equivalent) Installer’s Tip: An insulated staple is an ideal fastener for low-voltage wiring.
A single low-voltage cable running through a stud hole is unlikely to get damaged by a drywall nail or screw, but a bundle of cables would certainly be subject to damage. For the cost of some nailing plates, the nuisance and expense of replacing a damaged low-voltage wire inside a finished wall can be avoided. It is especially important on vertical runs between wall studs that bundles of low-voltage cable be secured with Velcro® straps such as Leviton’s SoftCinch™.
Installation Manual would also allow you to keep a paper copy of the labels for your client’s records. Letter and number cable identifiers are available from Ideal, Titan, and other label manufacturers. 8.4.7 Wiring Chart Every AC installation comes with at least a rudimentary circuit map attached to the door of the service entrance. Your SMC serves the same purpose as a location for a wiring identification chart for your low-voltage system.
In terms of height or distance from the floor, in-wall speakers have considerable flexibility as they are designed for wide dispersion. The wall/ceiling interface, however, is another room boundary. Placing a speaker too close to a room boundary can result in “doubling,” or an excessively boomy sound.
Installation Manual Telephone Distribution Module Telco Lines from Demarcation Point: A: __________ C: __________ B: __________ D: __________ Cables to rooms From Demarcation Point RJ31X For Alarm Override Data Module A B C D Bridged Voice Module (selected panels only) From Telco Demarcation point Label each cable 1 Telco Lines from Demarcation Point: A: ________ B: ________ C: ________ D: ________ 2 to Telco Distrib.
8.9.1 Standard General Practices for Installers • Always use a Structured Media Center as your main distribution point • Do not install SMC in a fire-rated wall. Choose interior wall spaces • Install your structured cabling following the star wiring or home run pattern • Aim for sweeping bends in your installations rather than sharp turns that can damage the cable; the minimum bend radius for Category 5 or 5e cable is about 1 inch, for RG-6 quad shield cable about 3 inches.
Installation Manual Aspects of the Pre Wire Installation Use j-hooks or similar devices designed to support cables. Staples by hand, or use staplers with depth stops. Use Velcro® to keep cables from becoming over-cinched. Use tie wraps loosely on large bundles. (See ‘Using Tie-wraps’) Use Velcro® tie wraps and cable straps to secure large bundles.
9 TRIM OUT Installation Trim Out TRIM OUT 9 Installation Trim Out At this point, you have familiarized yourself with the SMC or distribution center and the routing and installation of the low-voltage cable itself. This section will deal with the distribution modules, end point devices, connectors, jacks, and other components of structured cabling. 9.
Installation Manual Installation for Category 5 or 5e jacks 9 Strip 2" of cable jacket and position first pair, white-blue/blue. The center channel lets you preserve wire twisting to less than .5" from the termination point. Set 110-tool to low impact setting and turn cutting edge outward to terminate first pair. The patented ‘cuttting ledge’ trims the wire as you terminate, saving you a step.
Low voltage cable can also be terminated at one of the following connectors: 9 • RCA connectors TRIM OUT Installation Trim Out 9.1.4 Placing QuickPort Connectors and Jacks into QuickPort Wallplates • Speaker binding posts • Banana jacks Leviton makes installing connectors and jacks at wallplate locations both a simple and an easy operation.
Installation Manual Video amplifiers and splitters should be mounted on the right side of the SMC and their RG6 quad-shield cables brought in through the right side knockout at the top. This allows for a straight drop for the cables with virtually no bend to them. ✍Take Note: The above cable routing patterns are recommendations. The SMC panels are quite versatile and allow for many different cable routing patterns based on installer preference and SMC customization.
9 TRIM OUT Installation Trim Out Install the twisted cable pairs following the color code on the wires and the connectors. Use a wire punchdown/termination tool to secure the ends of the wire to the connectors following the same guidelines for untwisting and stripping the cable jacket as you did with the Category 5 or 5e jacks. 9.3.3 Coaxial Video Distribution Connections Using Passive Splitter Note: Video distribution is thoroughly covered in 9.4.3.
Installation Manual 9.4 Enhanced Infrastructure Advanced Small Office (ASO) Unit The Enhanced Infrastructure Platform serves networking and its multiple PCs as well as multi-room audio/video requirements. Security cameras and home theaters are also included in this platform that uses an SMC-420 as the distribution center. 9.4.
9 TRIM OUT Installation Trim Out The module can accommodate six (6) Category 5 or 5e cables; each terminates on the 4-pair 110 IDC Connectors lining its sides. IMPORTANT: Do not use the DC Power Supply Module with the following: To configure the connections for voice (with a Telephone Distribution Board), simply connect a 6-position, 4-conductor telephone patch cord from a port on the Telco Distribution Board to the port on the Category 5 Voice/Data Module that you wish to activate.
Installation Manual b. Run each twin power lead from DC powered components down to the Power Distribution board, assigning a separate DC output block to each. Connect the “+” side (usually striped) to POSITIVE and the “-“ side (usually plain) to NEGATIVE or GROUND; when using Cat 5 wire use the BROWN pair for POSITIVE and the GREEN pair for NEGATIVE or GROUND. The components are now wired to the DC Power Supply module.
Connect with Category 5 Patch Cor ds (10 ft/3 m max. 9 TRIM OUT Installation Trim Out 10 Base-T Ethernet Hub (with up to 5 data ts) por Computer Category 5 Voic e & Data Module Print er DC Pow er Supply Casc ade hubs for additional net w ork Connect with Category 5 ds Patch Cor (23 ft/7 meters max.) Computer Connect datatspor with Category 5 cable (295 ft/90 m max.) (328 ft/100 meters max.
Installation Manual Cable Disribution- Modem Outside the Structured Media Center DC Power Supply Incoming CATV Signal 10 Base-T or 10/100 Base-T Ethernet Hub (with up to 5 data ports) Line #1 Voice Splitter (from cable provider) Line #1 Voice Category 5/5e **Cable Modem Patch Cord Category 5 Voice & Data Module TRIM OUT Installation Trim Out Computer Expansion Jack TV RG-6 Coax 9 Category 5/5e Patch Cord Telephone Distribution Module NIC Computer Category 5/5e Patch Cords Category 5/5e Pat
• Ensure that both the hub and the soon-to-be connected workstation are in the OFF modes REAR 9 TRIM OUT Installation Trim Out • Plug one end of the patch cord into an available 10/100Base-T hub port 12V DC • Plug a patch cord at the other end of the link into the workstation NIC G. Power Port: Insert the 12 VDC adapter plug into this port on the 10/100 Base-T hub 9.5.
Installation Manual To install a stand-alone splitter: • Line up the module’s pins with the grid holes on the back of the SMC (the module can be mounted horizontally or vertically) • When set in the desired location, push the pin plungers to secure the module to the SMC • Route your RG6 quad-shield coaxial cable into the SMC, avoiding sharp or abrupt bends in the cable; install a male F-type connector at the end of each cable • A video input (from your cable TV or antenna, for example) goes into the center
Satellite Signal Distribution Using 3x4 Multi-Switch 9 Amplifier (Optional) CATV or Antenna (Optional) RG-6 Quadshielded Coaxial Cable TRIM OUT Installation Trim Out Satellite Dish LNBA ANT LNBB POWER PASS To TV (local antenna feed) 3X4 MULTI -SW 40-21 50MH x POWER PASS TV ITCH 1 2 RECE IVERS 3 4 * Diplexer Satellite Receiver #1 * RG-6 Quad Shielded Coaxial Cable Diplexer Satellite Receiver #2 input to receive TV antenna signals, which is best used in combination with a video amplifi
Installation Manual Multi-Room Stereo Analog Volume Controls and Audio Bridging Module R+ R+ R+ R+ R+ R+ R+ R- R- R- R- R- R- R- L+ L+ L+ L+ L+ L+ L+ L- L- L- L- L- L- L- From Amp Max 140 Room 1 Room 2 Room 3 Room 4 Room 5 9 TRIM OUT Installation Trim Out 2 Ea.
To connect to the Audio Bridging Module: 9 TRIM OUT Installation Trim Out • Using QuickPort snap-in modules with speaker binding posts, run a minimum of 16/2 CL-2 rated cable from the auxiliary LEFT and RIGHT speaker outputs of the entertainment center or A/V receiver. • Confirm that the polarity or consistency exists between the “+” (sometimes marked POSITIVE or colored RED) and “-” connections (sometimes marked NEGATIVE or GROUND, or colored BLACK).
Installation Manual 5. Remove the knob 9.6.4 Installing the Decora Digital Volume Controls 6. Tighten the nut without moving the tab 7. Replace the knob. The tab position will prevent the knob from turning to the point where the impedance toward the amplifier becomes too low. Note that there are two more settings available: position 11, which is for two 8-Ohm speakers per channel, and position 12 which is fully ON and should be used only for one 8-Ohm speaker per channel.
✍Take Note: Electrical boxes containing more than 110VAC 9 or higher must be equipped with an approved barrier that separates high and low voltage sections. • Crimp an 8-pin modular plug onto the Category 5/5e cable following T568A practices and plug it into the Volume Control Wall Unit. TRIM OUT Installation Trim Out • Finish the installation with a Decora Wallplate (provided). To connect the Hub to stereo equipment use fire-rated 14-18 gauge wire for the speakers.
Installation Manual 9 TRIM OUT Installation Trim Out Decora Media Hub Several topologies are possible within the DMS including: • An audio/video networking scheme, with A/V or PC components sending and receiving audio/video signals via a single send and multiple receive units and the centralized hub • A hub-to-receive model where information is sent from the hub to remote receive units • A point-to-point model where the send and receive units are linked directly together The DMS has the following features
Multiple Targets & Emitters Using Bridge 9 + 4 2 Pair Pair 3 Pa ir Pa ir 1 DC POWER SUPPLY MODULE CAT5 Brown Brown/White CAT5 4 Cat 5 BROWN D RE BLACK EN GRE E G WHITE (NC) RAN O QUICKPORT RJ-45 5 6 7 YELLOW 8 WHITE (NC) YELLOW NG E Cat 5 RA D RE BLACK BROWN N EE GR 9 10 1 2 3 4 BL OR GR BR O TARGET • Shine a flashlight on the front panel of the component • On A/V receivers, DVD players, and VCRs, the sensor is usually (but not always) in the tinted window near the LCD display
Installation Manual B. Network monitoring where the cameras are modulated and assigned a channel, and then “broadcast” over a pre-assigned “security” or monitoring channel (usually channel 75-80) for viewing on any TV connected to the coaxial cabling video distribution infrastructure. This approach also provides Video Sequencing, which automatically switches between up to 4 cameras to give a homeowner continual surveillance over several areas. 9.9.
9 TRIM OUT Installation Trim Out Once connected, check the camera again using a portable TV. 9.9.4 Outdoor Camera (Leviton 48213-ECC): Leviton’s outdoor version of the Decora Camera is manufactured to be weather-resistant. Its cabling and termination procedure is similar to the Decora Camera above, The installer should use the same procedure for checking the location’s suitability (using a portable TV and a temporary hook-up to check for lighting and positioning problems) as for the indoor camera.
Installation Manual To install a single TV set for direct monitoring follow the Indoor & Outdoor Camera Diagrams for direct monitoring: • Plug the F-connector terminated end of the RG-6 quad shield into any accessible auxiliary video input on the back of the set (usually designated VIDEO IN 1, 2 or AUX IN 1, 2) • Run the coaxial cables from the cameras to the TV set by passing them through the SMC first; this will comply with the easy-access star wiring topology and access the DC power supply • Use a femal
INDOOR CAMERA CONNECTION DIAGRAM 9-23 Cat 5 Patch Cord DC Adaptor Cat 5 Wire Colors ir 4 JACK 6 Pair 3 Pa Brown Brown/White Green Green/White Orange Orange/White 1 Blue Blue/White CAT 5 Gnd RCA Jack Signal Br h/ W wn o Br r G h/ W en re G NC Terminal block TV or VCR ir F to RCA In-line Adaptor Video Input Coax Video Cable RCA to F In-line Adaptor ir 2 Pa 6 JACK 1 2 Category 5 1 5 Pa Decora Camera Cat 5 Direct Monitoring Cat 5 Punchdown TRIM OUT Installation Trim Out 1X6 DC
Installation Manual OUTDOOR CAMERA CONNECTION DIAGRAM DC Adaptor 1X6 DC Power Distribution Board Cat 5 Patch Cord Cat 5 Wire Colors Brown Brown/White ir 4 5 Pair 3 JACK 6 Blue Blue/White CAT 5 or RCA Jack Signal Gnd No Connection BLK YEL WHT Orange Orange/White 1 Br h/ W wn o Br r G h/ W en e r G RED BLUE TV F to RCA In-line Adaptor Video Input Coax Video Cable ir VCR 6 Pa ir 2 u Bl h/ W e u l B CAT 5 1 JACK 1 2 Category 5 Green Green/White Pa Terminal block Camera TR
9-25 © Copyright 2001 Leviton Manufacturing Co., Inc.
Notch Filter 3x8 Bi-Directional Video Amplifier AUX Input Coaxial Video Cable with CATV/Satellite Signal (video/audio) and Modulated Camera Output (Channel 75-80) TV(s) or VCR (s) AC/DC Adaptor Green Green/White Coaxial Video Cable DC Power Distribution Module Blue Blue/White Supplied Video Cable Video Sequencer 5 1 Orange Orange/White Audio Signal (Outdoor Cameras Only) JACK 6 ir 2 RCA (or Coaxial) Video Cable 6 Category 5 Interface Cable Pair 3 Up to 4 Cameras Coaxial Video Cable Pa
Multi-Room Video Distribution Using 3x8 Bi-Directional Video Distribution Module 9 QuickPort Wall Plates with F-Connectors Note: Terminate All Unconnected F-Connectors with 75 Ohm Terminators TV TRIM OUT Installation Trim Out RG-6 Coaxial Cable Drops Typical TV or VCR Connection RG-6 Quad Shield Cable POWER IN 1 3 5 DIGITAL SATELLITE 1 7 OUT TO TV P1 2 CATV or Cable input (optional Notch Filter) Typical Dual LNB Satellite Dish Connection 4 6 IN FROM DISH 2 8 CABLE IN CI DIGITAL SATELLI
Installation Manual 4. Multi-Room IR Control: Covered under Multi-Room Stereo in section 9.6, the same IR Target and Emitter package is used to distribute remote-control commands from the remote viewing location (such as a master bedroom) back to the source A/V component (usually in the entertainment center).
9 TRIM OUT Installation Trim Out (channel 54) for that mode. Simply press the button UP until the number 77 appears. The Modulator is now programmed to “broadcast” the A/V source component over Channel 77 across the wholehouse coaxial cable infrastructure. Note: if you do not see the picture on the desired Channel, first check the immediate surrounding channels to make sure the Modulator was programmed correctly, or that the TV and modulator are tuned to the same channel.
DOCUMENTATION AND TESTING 10 Documentation and Testing Low-voltage cable is not as durable as other types of cable, and it has been specifically designed to meet strict requirements. Low voltage cable follows its own industry standard and requires specific tools and care to maintain the integrity of a structured wire system. It is more easily damaged during rough-in and drywall installation than other electrical cable and damage can go unnoticed.
• Audio cable (for speakers and volume controls) DEFINITIONS • RG-6 quad shield cable OPEN: Also known as an open fault.
Installation Manual between the handheld and remote tester, through the 1x9 Bridged Telephone Module. Leave the remote where it is, and move the handheld unit to plug into all jacks connected via cable to the 1x9 Bridged Telephone Module. All cable runs must pass the test. If any cable run fails or all runs fail, verify that all punchdowns at the jack are correct and follow the T568A pattern (see color code on the jack label). Then verify all punchdowns are correct at the 1x9 Bridged Telephone Module.
Leviton recommends one of the following Category 5/5e field testers: The following companies also sell their product through other companies under other product names; you are advised to ask which of these companies is the actual manufacturer of the tester. 10 TESTING Documentation and Testing Agilent Technologies Fluke Corporation 753 Forrest Street Marlborough, MA 01752 800-418-7111 508-486-0400 Fax: 508-786-9700 www.scope.com sales@scope.
Installation Manual Wallplate Area User Patch Cord SMC Outlet Permanent Portion of Cable Run Basic Link Channel Cross Connect (or patch panel) Equipment Cord "Basic Link" Test Configuration "Channel" Test Configuration - Covers just the permanent portion of cable run - Intended primarily for cable installers who must test cable before patch cords and network equipment are installed - Measures end-to-end cable run performance - More comprehensive test coverage ( See comments, next page) Please no
occurred since rough-in. Some phones might not work with polarity reversed, so be particularly careful to check the wire colors for proper polarity. • If no fault is obvious, re-test as for rough-in. ✍ Take Note: If dial tone is not available, perform the same tests as for rough-in before the jacks were installed. A splitting adapter may be necessary to test each line of each jack. A toner can be used with a normal telephone or buttset to test for dial tone.
Installation Manual 10.8 Documentation of Test Results As we’ve mentioned, you should record your results as you complete each test. Use the forms provided at the end of this chapter to right in your results by hand, or, if using a Category 5 or 5e tester, use the built-in database for recording your data. Note: The cable name or number, from the label on the cable must be entered into the tester or the form to coincide with the test on that cable run.
Test Documentation Form for Bridged, Power, and Audio Cable Connections Test Results Cable Number SMC Termination Wallplate Location Shorts Pass Fail Continuity Pass Fail Notes Submit this Test Results Form to Leviton Manufacturing Co., Inc. at: Address: 2222-222nd St. S.E., Bothell, WA 98021 Fax No.: 425-485-0112 E-mail: info@levitonvoicedata.
Test Documentation Form for Category 5 or 5e Links Test Results Cable Number SMC Termination Wallplate Location Auto Test Pass Fail Notes Submit this Test Results Form to Leviton Manufacturing Co., Inc. at: Address: 2222-222nd St. S.E., Bothell, WA 98021 Fax No.: 425-485-0112 E-mail: info@levitonvoicedata.
GLOSSARY A bone is the more permanent part of a communications network and it carries most of the traffic. Amplifier A component that boosts the strength of a transmitted analog signal as measured in decibels (dB); an amplifier is similar to a repeater in digital systems Bandwidth The difference between the highest and the lowest frequencies of a transmission channel (path for information transmission). Identifies the amount of data that can be sent through a given channel.
Installation Manual and data applications requiring a carrier frequency of up to 100 MHz. Now the most common cabling being installed for LAN connectivity. Defined by FCC Part 68, EIA/TIA-568, TIA TSB-36 and TIA TSB-40. Category 5e (Enhanced) CAT5e A Category of Performance for inside wire and cable. Used in support of signaling rates of up to 100MHz over distances of up to 100 meters. Calls for tighter twists, electrical balancing between pairs and fewer cable anomalies.
E H Electronic Industries Association/Telecommunications Industries Association A trade organization of manufacturers which set standards for use of its member companies. Many associations fall under the umbrella of EIA, though it has recently been absorbed by the TIA, or Telecommunications Industry Association. See www.eia.org or www.tiaonline.org. Headroom (also called Overhead or Margin) The number of decibels by which a system exceeds the minimum defined requirements.
Installation Manual both follow the 802.3 standard. Typically they transmit at 10 megabits per second. This is the most common local area network specification. Impedance The total opposition (i.e. resistance and reactance) a circuit offers to the flow of alternating current. It is measured in ohms, and the lower the ohmic value, the better the quality of the conductor. Interconnect 1.
O Point-to-point Transmission An uninterrupted connection between two pieces of equipment. Off-Hook When the handset is lifted from its cradle, it’s off-hook. The term originated when the early handsets were actually suspended from a metal hook on the phone. In modern phones, when the handset is removed from its hook or cradle, it completes the electrical loop, thus signaling the central office to provide dial tone.
Installation Manual RJ Registered Jack. RJs are telephone and data jacks/applications registered with the FCC. Numbers, like RJ-11, RJ-45, etc. are widely misused in the telecommunications industry. A much more precise way to identify a jack is to specify the number of positions (width of opening) and number of conductors. Example: “8-position, 8-conductor jack” or “6-position, 4-conductor jack”. S Series Wiring See Daisy Chain.
U UL Underwriters Laboratories, a privately owned company that tests to make sure that products meet safety standards. UL also administers a program for the certification of Category-Rated Cable. Universal Service Order Code An old Bell system term identifying a particular service or equipment offered under tariff.
APPENDIX B: Frequently Asked Questions 1. Why should I install Leviton’s Integrated Networks rather than assembling my own from off-the-shelf components? Leviton offers a single, convenient package of tested materials that meet commercial grade requirements. They are designed to work together without conflicts. They are also, in part, simple plug and play architecture that makes the installer’s job easier.
5. Why not use Category 3 cable when it will satisfy the job requirements? Leviton recommends Category 5 or 5e for all low-voltage installations because of its greater carrying capacity that is more suited to current and future high-speed data applications. You’re always better off installing a higher grade, Level 2 structured cable system as it is far more adaptable to system changes and additions. 6. I understand that I can use Category 5 or 5e cable instead of coaxial for video applications.
Installation Manual Notes: N NOTES For more information call your Leviton representative or the Leviton Technical Hotline at 800-722-2082 © Copyright 2001 Leviton Manufacturing Co., Inc.
Notes: N NOTES N-2 For more information call your Leviton representative or the Leviton Technical Hotline at 800-722-2082 © Copyright 2001 Leviton Manufacturing Co., Inc.
LEVITON INTEGRATED NETWORKS Installation Manual for Residential Installation Manual for Residential Structured Wiring www.leviton.com/lin www.levitonvoicedata.com Tech Line: 800-722-2082 Customer Service: 800-323-8920 W-818/E1-35M rs E-1 Structured Wiring Version 2.
