Installation manual

The DC Power Distribution Module features:
• 12 outputs that provide 12 Vdc power for up to 12
devices
• F-connector output for the 3 X 8 Bi-Directional Video
Module
• 1500 mA maximum
•Six removable double screw terminal jacks with slot
drive screws
• Shipped with (6) 18 gauge pigtails with 2.5 mm
power jacks
• Fully regulated (12 volt DC regulated output)
•1 Input - utilizing plug-in DC transformer power sup-
ply
• Dimensions: 6.58" X 2.5" X 1.5"
Use the chart on Table 6.5 (below) showing the power
consumption of various modules to ensure that you will
not exceed the current for one Power Distribution
Module. Just add up the current for each module you
are using. If the total current exceeds 1450 mA, use a
second DC Power Distribution Module with its DC
Power Supply.
6.5.3 Multi-Room Infrared (IR) Repeater
Infrared technology allows for the remote control of
audio/video devices when the user and the device are
in different rooms. Leviton’s IR Extender consists of
three components:
1. IR Target (P/N 47621-MIE)
2. IR Emitter (P/N 47621-CMS)
3. 110 Distribution Block (P/N 47603-110 or 47689-B)
The IR Repeater system is simple: the IR target takes
the signal from a remote control for an audio/video com-
ponent, such as a DVD player, and converts it to a low-
voltage electrical signal. This signal is converted back
at the component to be controlled by the IR emitter. The
IR target is installed in a ceiling or wall and connects to
the IR emitter with Cat 5 cable. Each component has its
own emitter. An IR distribution block installed inside the
Structured Media Center routes each signal to the
appropriate component.
The IR Repeater has the following features:
• Low-profile, flush-mount design of the target
•Two signal connections and two power connections
• Easy-to-install, adhesive backing on emitter
• DC power supply required
Installer’s Tip: Be sure to discuss the location of the
various IR targets with your client before wiring them.
Some might object to a ceiling installation and other
will want to designate a specific location.
The IR Emitter plugs into a dedicated Category 5 or 5e
jack at the equipment location. The Repeater requires a
dedicated Category 5 or 5e cable from the target to the
SMC and to the Category 5 or 5e jacks.
6.6 Multi-Location Networking
With the advent of multiple PC households and home
offices, home networking will be more in demand by
your customers and clients. Category 5 or 5e cable
allows both high speed and high capacity data trans-
fer. A Category 5 or 5e module and hub provides a
central point from which to service multiple PC’s and
peripherals.
Depending on the number of devices and PCs that
require network access, you can choose additional
Category 5 or 5e modules combined with a network hub
to connect the termination points. Leviton offers two
such hubs:
• The 10Base-T Network Hub
• The 10/100Base-T Network Hub
The combination of structured cabling and a network
hub creates an in-home Ethernet data network when
used with network cards or adapter-equipped PC’s and
associated software.
6.6.1 10Base-T
Network Hub
The professional-
grade10Base-T
Network Hub offers:
• Category 5 or 5e
patch cord connec-
tion to the Category
5 Voice and Data
Module
6-7
For more information call your Leviton representative or the Leviton Technical Hotline at 800-722-2082
© Copyright 2001 Leviton Manufacturing Co., Inc.
6
DESCRIPTION
of Leviton
Integrated
Systems
10Base-T Network Hub
Module Power Consumption (mA)
3 X 8 Bi-Directional
Video Module
Decora Media System
Decora Camera
Outdoor Camera
Video Amplifier
Video Sequencer
IR Emitter
Digital Volume Control
10/100Base-T Hub
Module Power Consumption Table 6.5
80
60
70
225
500
100
500
75
1200