Installation manual

The module can accommodate six (6) Category 5 or
5e cables; each terminates on the 4-pair 110 IDC
Connectors lining its sides.
To configure the connections for voice (with a
Telephone Distribution Board), simply connect a 6-po-
sition, 4-conductor telephone patch cord from a port on
the Telco Distribution Board to the port on the Category
5 Voice/Data Module that you wish to activate. The
jacks on the Cat 5 module are designed to accommo-
date both 6-position, 4-conductor telephone cords as
well as 8-position, 8-conductor cords.
9.4.2 Installing the DC Power Supply Module
(Leviton 48212-DCS)
The DC Power Supply Module supplies up to 1500mA
of regulated 12 VDC power for the Home Monitoring
Security Cameras, the IR Targets and Emitters, and
more. It should be considered as the first step in build-
ing an Enhanced Structured Media subsystem. As de-
scribed previously, Leviton’s DC Power Supply Module
takes the place of multiple DC plug-in supplies inside
the SMC. The unit comprises two pieces: an AC-DC
Power Converter which plugs into the AC Power Supply
Module (recommended) or a receptacle outside the
SMC, and a +12VDC Regulated Power Distribution
board which regulates the AC-DC Power Converter’s
output and distributes it to up to 12 DC-powered com-
ponents inside and outside the SMC utilizing 12 wire
pairs with 2.5mm DC power plugs on one end.
IMPORTANT: Do not use the DC Power Supply Module with
the following:
• 10 Base-T Ethernet Hub (P/N 47605-EH)
• Or any device, which is, rated either AC power, below
12VDC, or otherwise incompatible. Other
wise, dam-
age to the component will r
esult.
Installing the DC Power Supply module:
a. Do not plug the AC-DC Power Converter into the AC
receptacle until the DC power supply module wiring
is complete and verified to be correct!
b. Connect the plug from the AC-DC Power Converter
into the jack labeled POWER INPUT, on the left side of
the +12VDC Regulated Power Distribution Board.
Connecting components to the DC Power Supply
module:
a. Wire types: you can run Category 5 or 5e cabling
from the Power Distribution board to the various sys-
tem components. But for components mounted in-
side the SMC use the cord sets supplied with the DC
Power Supply Module. Note that while the Leviton
DC Power Supply Module replaces the various DC
power supplies that come with other components,
you can still use the jack and connected wire by sim-
ply cutting it off and “hard-wiring” the other end to
one of the DC output connectors on the Power
Distribution board. This eliminates having to wire an-
other jack to plug into the powered device, if more
than 6 are required.
For more information call your Leviton representative or the Leviton Technical Hotline at 800-722-2082
© Copyright 2001 Leviton Manufacturing Co., Inc.
9
TRIM OUT
Installation
Trim Out
9-7
Instructions for Connecting Voice and Data
in the Structured Media Center
Install short 8-position patch
cord between the two "Service
Bridge" jacks to connect
incoming dial tones to the
telephone distribution jacks.
Install 7-inch silver telephone cords
from the telephone distribution jacks
to whichever category 5 jacks you
wish to activate with dial tone.
Install 1-foot Category 5 patch cords
from any category 5 jacks you wish to
activate with data networking services
to a data network Hub.
To Hub
Route an RG6 cable from the output of the video amplifier. Crimp on an
F-connector and attach to the "IN" connection of the video splitter.
Route RG6 Cables from CATV outlet locations. Crimp an F-connector
onto each cable and attach to any "OUT" connection on the video splitter.