Owner's Manual

ManualsBrandsAudioSource ManualsHome AudioStereo dual-source power amplifier

OWNER’S MANUAL

AD1002

AudioSource®

13970 SW 72nd Ave

Portland, OR 97223

503.914.4688

www.audiosource.net

AD1002 Owner’s Manual 51115

Congratulations on your purchase of the AudioSource® AD1002.

Please take a few moments to read this entire manual, and be sure to

retain this document for future reference. Please read and observe all

safety instructions detailed on page 2.

NOTE: If any part of this product is damaged or missing, please call your

dealer or AudioSource® directly at 1.877.715.5439 or 503.914.4688.

Please read your warranty and retain your receipt and original carton

for possible future use.

For more information about AudioSource® electronics, speakers and

accessories please visit www.audiosource.net

AD1002

Digital Stereo Power Amplifier

FEATURES:

MAIN / INTERRUPT priority input switching

MAIN auxiliary output

Speaker A/B switching

Front panel Balance and Volume controls

Signal sensing “Power On” and Trigger mode

SPECIFICATIONS

Stereo (8 ohm): 50W per channel, <1% THD+N

Stereo (4 ohm): 75W per channel, <1% THD+N

Bridged Mono (8 ohm): 160W, 1kHz, <1% THD+N

Frequency Response: 10Hz ~ 30kHz, -2dB/ +1dB

Signal to Noise Ratio: 100dB below 50W output into 8 ohms

w/20kHz Lowpass filter

Channel Separation: 65dB @ 1kHz, referred to 50W output

into 8 ohms

Input Sensitivity: 700mV input for rated 50W output

into 8 ohms

AC Power Consumption: 200W maximum

Net Weight: 4.7lbs / 2.2kgs

Gross Weight: 6.8lbs / 3kgs

2.15”

(55mm)

16.9” (430mm)

7.65”

(194mm)



Left

Right



Balance

Volume

SPEAKERS

AD1002

Min

-AX

POWER

Rear mounted treble and bass controls

Bass/Treble Control: +/- 12dB @ 100Hz and 10kHz

DIGITAL

STEREO POWER AMPLIFIER

Summary of content (5 pages)

PAGE 1
AD1002 OWNER’S MANUAL AD1002 Digital Stereo Power Amplifier FEATURES: Congratulations on your purchase of the AudioSource® AD1002. Please take a few moments to read this entire manual, and be sure to retain this document for future reference. Please read and observe all safety instructions detailed on page 2. MAIN / INTERRUPT priority input switching NOTE: If any part of this product is damaged or missing, please call your dealer or AudioSource® directly at 1.877.715.5439 or 503.914.4688.
PAGE 2
AD1002 OWNER’S MANUAL CAUTION RISK OF ELECTRICAL SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL! The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
PAGE 3
AD1002 OWNER’S MANUAL Balance DIGITAL STEREO POWER AMPLIFIER Volume SPEAKERS POWER A 1 B 3 -AX Min 4 AD1002 Figure 1. Front Panel FRONT PANEL CONTROLS 1. Power Switch Switches the AD1002 on or off. A red LED indicates connection to AC power while in standby mode. Turns green indicating audio signal is present. 2. Speaker Selector Selects speaker zone A or B. For A + B zones push both buttons in. 7 Right Left 2 10 8 3. Balance Fades speaker output between the Right and Left Channels 4.
PAGE 4
AD1002 OWNER’S MANUAL APPLICATIONS Limited Warranty STEREO SETUP In this conﬁguration, the mode switch is set to “Stereo”. Connect the line out jacks from a stereo pre-ampliﬁer or source to the MAIN input jacks of your AD1002. Next connect your speakers to the terminals marked “Speaker A” observing proper polarity. Select the “A” speakers using the front panel zone selection buttons. Connect a second (optional) pair of speakers to the terminals marked “Speaker B”.
PAGE 5
Thank you for purchasing your Audiosource amplifier from Crutchfield. The manufactures warranty for this amplifier is 2 years, however thanks to our partnership with Audiosource, this has been extended by Audiosource to 3 years from the original date of purchase. During this timeframe Crutchfield will, at Crutchfield’s sole discretion, exchange the amplifier if it is found to be defective.