Model APS-901E Installation Manual Keyless Entry and Remote Start System Table Of Contents: Before You Begin Page 2 Wire Harnesses Quick View Page 3 - 4 Installation Of The Major Components Page 5 6 Pin Power Harness Wiring Page 6 - 7 12 Pin Accessory Input/Output Harness Wiring Page 7 - 9 4 Pin GND, Alarm Bypass Output & Parking Light Harness Page 11 Door Unlock Harness Wiring Page 12 - 13 Telematic Port Information Page 13 6 Pin Antenna Harness Page 13 Diesel Engin
Before You Begin PROFESSIONAL INSTALLATION IS STRONGLY RECOMMENDED Roll down window to avoid locking the keys in the vehicle during installation. Avoid mounting components or routing wires near hot surfaces or near moving parts like the steering wheel as it may prevent proper operation of the vehicle. Tape or loom wires under the hood and dash for protection as well appearance. Use grommets when routing wires through metal surfaces to prevent chafing and shorting.
12 Pin Main Wiring Harness #1124295 1 Green/Orange 2 Green/Yellow 3 Green 4 Brown/Black 5 Brown 6 Gray 7 Black/Yellow 8 Black/Red 9 Black/Blue 10 Black/LT. Green 11 LT.
6 Pin Power/Start Harness #1123742 1 Blue 2 Red/White 3 Green 4 Purple 5 Red 6 Yellow Ignition 1 (+) Battery 1 - 12V (+) Ignition 2 (+) Accessory (+) Battery 2 - 12V (+) Starter Output 4 Pin 2nd Main Harness #1124294 1 Black 2 White/Red 3 Yellow/Black 4 White Chassis Ground Parking Light Relay Input To Controlling Alarm's Ignition Input Parking Light Relay Output 6 Pin Antenna Harness #1124296 1 Red 2 Green 3 Black 4 Gray 5 Blue 6 NC + 5 VDC RX Ground Valet Enable LED Cathode 4 128-9300 4 of 24
WARNING! This Remote Start is to be used in vehicles with AUTOMATIC TRANSMISSIONS only! Although this system is a sophisticated device with many advanced features, IT MUST NOT be installed into a vehicle with manually operated transmission. Doing so may result in serious personal injury and property damage! INSTALLATION OF THE MAJOR COMPONENTS: CONTROL MODULE: PART # 1365398 Select a mounting location inside the passenger compartment (up behind the dashboard).
IMPORTANT! DO NOT PLUG THE EIGHT PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT/OUTPUT HARNESS INTO THE CONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER SELECTING YOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE VEHICLE BATTERY PRIOR TO MAKING ANY CONNECTIONS. NOTE: Do not remove the fuse holders from this wire harness. Fuses must be used and located as close as possible to the power source for adequate protection of the vehicle.
In both mechanical and electrical neutral start switch configurations, the connection of the Yellow wire will be made to the low current start solenoid wire of the ignition switch harness. This wire will have +12 volts when the ignition switch is turned to the start (crank) position only. This wire will have 0 volts in all other ignition switch positions. NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used).
3 Green Wire: Door Unlock (-) Output The Green wire provides a (-) Negative Pulse when the transmitter is used, while the vehicle is running by remote start, to unlock the doors. See Page 12-13 for use of this unlock output. 4 Brown w/ Black trace Wire: Positive Inhibit Input The Brown w/ Black Trace wire provides an instant shutdown for the Remote Start Control module whenever it gets + 12 volts.
Black w Blue trace Wire: Pulsed Ground Output Before Start The Black w/ Blue Trace wire will provide a 1 second 300 mA pulsed ground output 500mS before GWR becomes active as well as when the transmitter is used to disarm the system. Typical use for this output would be to disarm a factory theft deterrent system to prevent false triggering of the factory alarm when the remote start unit engages or when the system is used to unlock the doors.
A. Sensor By Pass: If there is a Non Plug in Sensor used with the alarm system and it is not shunted during the Remote Start activation period, then vibration or noise from the running vehicle can cause the alarm to trigger. In this case, connect the Light Blue Wire to terminal #86 of a external relay. Connect terminal # 85 of the relay to a fused + 12 volt battery source. Cut the sensor's trigger wire and connect one end of the cut wire to terminal #30 and the other end of the cut wire to terminal #87a.
4 Pin Additional Harness: Parking Light Flasher I/O Siren & Ground 1 Black: Chassis Ground Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self tapping screw and ring terminal. 2 White w/ Red trace Wire: Parking Light Relay Input Wire This wire is the common contact of the on board parking light flasher relay.
3 Wire Ground Switched Door Lock Circuits: Use of Green wire from main connectors harness. In this application, the Green wire of the main wiring harness provides a ground pulse when the transmitter button is pressed and held for 3 seconds while running under control of the remote start. Connect the Green wire to the low current ground signal wire from the factory door unlock switch to the factory door unlock relay. See the following diagram for Wiring Detail Connect to the unlock side only.
Resistive Circuits, Multiplex Circuits As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistor, a door lock interface, or a data module. You can search the vehicle @ www.avxtech1.com, www.Flash-It. com for vehcile specific information, or contact our tech service line or web site for additional information.
DIESEL ENGINE SETTINGS: NOTE: When selecting Diesel operation, (Bank 3 Feature #12), over gasoline, the only change is to the ignition circuits. When Diesel is selected, the ignition circuits will power up 10, 15, or 20 seconds before the start circuit. The intent of this feature is to allow the glow plug warming required by some diesel engines. If your vehicle is a instant start diesel, it is not necessary to activate this feature.
DIAGNOSTICS: Enter Bank 3 and turn on selectable feature # 10 as described on the front pages of this manual. NOTE: Diagnostic mode is a temporary mode. Once you have accessed the diagnostic mode, the unit will pause for two seconds then begin to flash the last stored shut down code. This code will be displayed three times in succession, then the unit will automatically exit the diagnostic on mode. The parking lights will flash a number of times indicating the reason for the last remote start shutdown.
To Exit Remote Start Override Mode: 1) With the system disarmed, Press and Hold the PBLED on. 2) Turn the ignition switch on, off, on, off, on, off. 3) The LED turns off indicating that the R/S unit is fully functional one again. DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION OF THE MANUAL SHUT DOWN / ENABLE FEATURE.
KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allow a margin of safety and will prevent the vehicle with a Mechanical Neutral Start Switch from starting in gear. WE ADVISES THAT YOU MAINTAIN THE FACTORY CIRCUIT WHENEVER POSSIBLE. The following two circuits may be used only if the above circuit is not available.
NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be connected to the hood pin switch. If the hood pin switch is also used for an alarm trigger input, be certain to use the dual diode set up shown earlier in this manual.
The transmitters are pre-programmed from the factory, If you find you need to program new or additional transmitters follow the instructions below. PROGRAMMING BANK 1 (TRANSMITTERS): 1) Turn the ignition key to the on position. 2) Press and release the valet/programming switch 3 times (Siren Chirps Once). 3 Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren. 4) Turn the ignition switch off.
128-9300 20 of 24 SELECTABLE FEATURES harness and follow program prompts. Siren chirps 5 times indicating access to feature program mode. Launch the application on your PC,,Connect the module via the USB to DBI Turn ignition off then on, off then on, off then on, off then on to enter web/on-line feature selection Bank 5. If Programming via PC while connected to + 12 VDC you must manually enter the programming mode as shown below.
PROGRAMMING BANK 3 (REMOTE START ): You can enter Bank 3 from Bank 2 by turning the ignition key off then on after you've made the changes you wanted in Bank 2, (Siren Chirps 3 times). You can also go right to bank 3 by: 1) Turn the ignition key to the ON position. 2) Press and release the valet/programming switch 3 times (Siren Chirps Once). 3) Turn the ignition key off then on (Siren Chirps 2 Times). 4) Turn the ignition key off then on (Siren Chirps 3 Times).
128-9300 22 of 24 6 Chirps Flashing Tach < 0.5V B4 Start On Steady Voltage >0.5V B4 Start Off During Crank Not Available Off During Crank On During Crank Off On 4th Parking Lights 5th Input Check 6th Voltage Level 7th Ign. 2 Select 8th Ign. 3 Select 9th Accy. Relay 10th Diagnostics NOTE: When averaging, the engine must be started Averaging 14th Crank Averaging Gnd When Running O/P Same as Ign 1 O/P Same As Accy.
NOTES 23 128-9300 23 of 24
Wire Side View Of Connector 1 Blue (Ign 1) 2 Red/White (+ 12VDC Relays Ign 1 & Ign 2) 3 Green (Ign 2) 4 Purple (Accessory) 5 Red (+ 12VDC Relays ACC & Start) 6 Yellow (Starter) 6 5 4 3 2 1 Connect Data Module Selectable DBI or ADS Protocol APS901E White (Parking Light Relay Output) White/Red (Parking Light Relay Input) Yellow/Black (To controlling Alarm’s Ign Input) Black (Chassis Ground) No Connection Blue (LED -) Grey (Valet) Black (-) Green (RX) Red (+) White (TX) Yellow (RX) Black (-) Red (+)
