Remove door panel.
0 \ MANUALL y CHECK THE MOVEMENT OF THE Adjust the registers or guides If the window WINDOW does not operate freely 0 OPTIONAL OPERA TION: A .IN ORDER TO USE THE SMALLEST CAP ON SOME VEHICLES, IT MA Y BE NECESSARY TO MOVE BACK THE WINDOW REGULATOR ASSEMBLY. B .AFTER REMOVING TO CHOOSE KIT NO.2 4 ORIGINAL SUITABLE BOLTS SPACERS FROM AND THEIR SEATS, BOL TS (SUPPLIED REFER TO THE TABLE IN KIT NO.2).
C .INSERT SPACERS BETWEEN MANUAL Check that the bolts of the window MECHANISM AND DOOR-PANEL assembly are tight KIT NO.3 From Kit No.3, below. choose the correct adaptor for the model of vehicle. See adaptor Table N. 1 ALFA ROMEO -AUTOBIANCHI -BEOFORO -OAF OATSUN -FIAT -LANCIA -MERCEOES -NISSAN OPEL-PORSCHE-SUBARU N. 2 ARO -CITROEN TALBOT N.3 -PEUGEOT AUDI -BMW -FIAT -FORD PORSCHE -VOlKSWAGEN -RENAUL N. 7 OPEL N. 8 DAIHATSU -MITSUBISHI CHEVROLET -G.M. N.
Take caution in removing If the handle is fixed adaptor from Kit. Do not twist-off. with a screw, use it to fix the adaptor 0 INSERT INTO GEAR THE SLEEVE TRANSMISSION KIT NO.4 t J i B il ,... " ,'-.. ""'t,{ ... Geared sleeve to be inserted towards inside of vehicle A) Insertion from the red marked side. B) Insertion from the opposite side of the red mark. I ~ " ~ ~ Cear Conversion t t'! l ;c " A) Wrong: too long. B) Wrong: too short.
B A) Remove the screws. B) Rotate the geared motor to the required C) Retighten the screws in their seats. ~ position ~ @ ~ ~ i Drill door panel to hook-up springs, I ~ ~ IMPORTANT: I ~ The power cable for the motor must always be positioned downwards ~ ~ A B c K'T,1!9"1. ~ , , ., . , ./ ' .(~l I ; , .I .\. .('(I ..'f('(i' ..t. (. (i. ..~'(.(,.; .\. ...~. :~.. .(1~ . ;'A;,<1 <1 , ( .b' J .. ., .. ;:; , ~. A) Fastening with two brackets. B) Fastening with brackets and springs.
~ ~ Take springs and wire clip out of KIT No / /. 1 1) Spring. 2) Wire clip. Hook up springs and lock hooks IN CASE THE MOTOR, OR PARTS OF IT, ARE IN DIRECT CONTACT WITH ANY METAL PARTS, THE SUPPLIED PADDING SHOULD BE USED AS SHOWN BELOW.
~ NO.3 No.2 Small. Medium No.3 Larg. No.1 The grommet retainer ring cap locks to panel by means of a KIT NO.1 I L r 1 --.:- :"1 , ! I ~. '""U --' The grommet with the has retainer to come through the door casing at least 5/32 in order to be locked 1 ring. 1 3 To choose the proper grommet cap, follow this procedure: -Insert grommet cap no.1 (SMALL) into the panel, if it does not come through, no.2 (MEDIUM) and then, if necessary, no.3 (LARGE). try - I B MAX No.
UNIVERSAL ELECTRIC WITHOUT CLUTCH ART.33000013 [!!J FIT CAP ON DOOR Fit the Cap on the grommet NOTE! WINDOWS PANEL and fit the panel on the door When the regulator pivot does not come out from the panel (photo A and B) you can use cap No. O for a better appearance.
INSTALLATION BUICK CENTURY EXAMPLE FOR ELECTRIC POWER IN SOME CARS IN THE U.S. (4 Doors) front left BUICK CENTURY (4 Doors) WINDOWS rear right -insert gear H 15 (insert from red marked side) -adaptor No.8 -turn transmission side of geared motor towards inside of car -affix geared motor with springs -grommet No.1 -cap No.1 -adjust bracket on transmission shortened 1" -insert gear H 15 (insert from red marked side) -adaptor No.
FORD TEMPO front right HONDA -adjust bracket on transmission -rotate geared motor 1800 on transmission -insert gear H 15 (insert from red marked side) -adaptor No.12 -apply paddings to geared motor -turn transmission side of geared motor towards inside of car -affix geared motor with bracket shortened 2.2" -grommet No.1 -cap No.1 ACCORD front right -adjust bracket on transmission -insert gear H 15 (insert from red marked side) -adaptor No.
~ II\ ~ =~. .~Ci .', . - O '., ~c ~--'(l1 1( .'. ki \~ .. CHEVROLET/GMC S-10/15 PICKUP front left -shorten bracket on transmission 1.6" -gear H 15 (insert from red marked side) -adaptor No.8 -apply paddings to geared motor -turn transmission side of geared motor towards inside of car -affix geared motor with two brackets -grommet No.1 (may need to use with 2.9" plastic round washer) -cap No.1 DODGE CARA V AN front left -shorten bracket on transmission 1.
Listed here are wiring diagrams kits using the wiring kits. NOTE! of typical installations for the Electric window For safety reasons it is necessary that the power supply to the windows be connected to the appropriate terminal of the ignition side of the ignition relay block. It is recommended that only wiring kits be used. Whenever this is not possible, proper wiring of at least 16 AWG must be used with the suitable in-Iine fuse. assumes no liability in case of non-compliance ELECTRICAL .
ELECTRICAL CIRCUIT: * Use original 3 SWITCH WITH 6 CONTACTS AND SEPARATE wiring, Art. 33020010 complete with 25 Amp. fuse.
FUSE 50 Amp 21
