BT-HP1 OWNERS MANUAL
Bluetooth® is a trade mark of Bluetooth Special Interest Group (SIG) Inc. WARNING! Never disassemble or adjust the unit. WARNING! To prevent injury from shock or fire, never expose this unit to moisture or water. 1. T his device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2.
INTRODUCTION The BT-HP1 is a Bluetooth® stereo headset. The stereo headset is foldable and the retractable design makes the stereo headset is very easy to take with you. The stereo headset supports the following Bluetooth® profiles: HSP —— Headset Profile HFP —— Hands-free Profile A2DP—— Advanced Audio Distribution Profile AVRCP——Audio/Video Remote Control Profile Please read this user manual carefully before use.
CONTROLS AND INDICATORS 1 Foldable and retractable headband 2 + button: Volume up 3 ﹤ button: Previous track 4 ﹥ button: Next track 5 Built-in microphone 6 LED indicator 7 Multi-Function Button (MFB): Power on/power off/answer a call/end a call/reject a call/ microphone mute/call transfer/redial last number/voice dial/pause/play 8 Charging jack 9 – button: Volume down 4
OPERATION Charging the headset The stereo headset comes with a built-in rechargeable battery. Prior to using the stereo headset it is recommended to charge the battery fully for the first time. The charging time is about three hours. When the stereo headset battery is low, the red LED flashes twice and the headset emits three tones every 20 seconds. Please recharge the headset battery. Using the USB cable Connect the USB cable to a computer USB port and the 2.5mm plug to the charging jack of the headset.
Turning the stereo headset on and off Action LED indicator Power on Function Press and hold MFB button for 3 to 5 seconds until blue LED flashes Blue LED flashes every second Power off Press and hold MFB button for 3 to 5 seconds until red LED flashes Red LED flashes once for 1 second Note: In order to save the battery charge, the stereo headset will turn off automatically after five minutes if no devices are connected to the stereo headset.
Pairing the stereo headset with a Bluetooth® cell phone Prior to using the headset for the first time, you have to pair it with a Bluetooth® capable cell phone. The pairing procedures can differ between cell phone models and manufacturers. Please refer to your cell phone user’s manual for further information. The general pairing procedures are as follows: 1. Place the stereo headset and Bluetooth® cell phone approximately three feet apart without physical obstructions such as walls etc. 2.
Pairing the stereo headset with a Bluetooth® audio device You can connect the stereo headset to a Bluetooth® audio device transmitter to listen to music wirelessly. Perform the following steps to pair the device to the stereo headset: 1. Place the stereo headset and Bluetooth® audio device transmitter approximately three feet apart without physical obstructions such as walls etc. 2. Enter the headset’s pairing mode (please refer to Entering pairing mode). 3.
Re-connecting with a Bluetooth® device a) Automatic connecting Every time the stereo headset is turned on, it will connect to last connected device automatically. b) Manual connecting When the headset doesn’t connect to a device supporting HFP, press the MFB button twice and the stereo headset will connect to last connected HFP device. When the headset doesn’t connect to a device supporting A2DP, quickly press MFB button once and the stereo headset will connect to last connected A2DP device.
Stereo Headset Phone Functions Function Action Cancel a call Quickly press the MFB button. Answer a call Quickly press the MFB button. Reject a call Press and hold MFB button for 2 seconds. Release MFB button and a tone is heard. End a call Quickly press the MFB button. Volume up Touch and hold the + button. The volume will increase to a maximum level. Volume down Touch and hold the - button. The volume will decrease to a minimum level.
Stereo Headset Phone Function (Three Way Call) Function Action End current call and answer a new incoming call Quickly press the MFB button once. Keep current call and answer a new incoming call Quickly press the MFB button twice. Call transfer (Pick up another call while on a call) Quickly press the MFB button twice. Note: Not all cell phones support all functions listed above. Please refer to your cell phone’s documentation manual for further information.
Note: When playing music on some cell phones, the music will be transmitted to the cell phone’s speaker instead of the headset. You have to select “transmit the sound via Bluetooth” in the settings menu and then choose “BT-HP1” as speaker device. The music will then be transmitted to the headset. Please refer to your cell phone’s documentation further information.
Stereo Headset Status Tones When the stereo headset is connected to a Bluetooth® device the LED will provide the following status indications on the headset. Tone Headset Status Two short tones Entering pairing mode Two tones every 5 seconds Two tones every 5 second during a call indicates the microphone is muted Three tones every 20 seconds Battery charge is low CARE AND MAINTENANCE The following recommendations will ensure you get the maximum use and enjoyment from your stereo headset.
SPECIFICATIONS Bluetooth® specification Bluetooth® V2.1+EDR Bluetooth® profiles HSP, HFP, A2DP and AVRCP Operating distance 30 Feet (10 meters), Class II Operating time Music: Up to 10 hours Talk: Up to 11 hours Standby time 200 hours Charging input DC 5A 130mA Charging time Approximately 3 hours Dimensions 6.22 x 6.14 x 2.16 inches (158×156×55mm) Weight 3.
12 MONTH LIMITED WARRANTY Applies to Audiovox Mobile Video Products AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company’s option) without charge for parts and repair labor.
128-9135