CarStream BLUETOOTH & SATELLITE RADIO INTEGRATION KIT for selected Volkswagen / Audi vehicles using Satellite Radio emulation Installation Guide/User manual
Copyrights and Trademarks Copyright 2015 VOXX Electronics Corporation All Trademarks and Logos are the property of their respective owners. All rights reserved.
Table of Contents Warning and safety ..........................................................4 Operation .......................................................................... 19 Product registration .........................................................5 Managing Multiple calls ....................................................20 Kit contents ......................................................................6 Music Control ..............................................................
Warning and safety! Please read these instructions carefully before proceeding. Failure to follow instructions may result in improper operation or injury. VOXX Electronics Corporation, its regional offices, distribuotrs or resellers won’t take any responsibility for any damage or injury as a result of using the integration kit. - Do not open, disassemble or alter the interface in any way. - Do not insert anything into the casing.
Congratulations on your purchase! Thank you for purchasing this integration kit. Please review this booklet before operating the unit. This interface was designed and manufactured to seamlessly integrate with your vehicle’s factory audio system. Product registration and have unlimited access to our online support system. To register your Audiovox product, please complete the following steps: 1. Visit http://www.audiovoxoei.com 2. Look up and save the serial number of the product. 3.
CarStream kit contents CarStream module Vehicle Interface Harness BCS1M Bluetooth module Clip and 2-sided mount Optional accessories (sold separately): For more accessories, visit www.audiovoxoei.
DIP switch settings The following DIP switch settings are used to configure the CarStream module to interface with the various radio systems. Before installation, set the DIP switch to the position shown for the corresponding radios and desired features. AUDI NAV+ VW/ AUDI CONCERT OFF ON OFF ON Use this setting if car is equipped with AUDI Navigation plus radio system. CarStream module VW NAV AUDI SYMPHONY OFF OFF ON Use this setting if car is equipped with base VW radio or AUDI concert radio.
The factory Satellite tuner connections must be accessed, for which the location varies depending on vehicle (inside trunk panels, under passenger seat, etc). The harness provided with the kit is long enough to reach from these locations. If there is a factory satellite tuner, unplug its two connections. This CarStream kit does not support the retention of the factory satellite radio tuner at the time of printing this document.
Attention installer! Please read the following! Audiovox strongly recommends that the unit be installed in an easily accessible location! DO NOT PLACE IT BEHIND THE RADIO AND DO NOT HIDE UNDER CARPET! Whether the unit is professionally or self installed, put the module where you, the end user can get to it easily in the future. (Have the installer show you where the interface module is installed.
Connection diagram - Bluetooth and AUX inputs CarStream module (front) Auxiliary device (not included) Vehicle Interface Cable CarStream module (back) Upgrade Port Bluetooth module USB to PC or MAC computer AUX cable (optional) * Do not connect the Bluetooth module under any circumstance to the SIRIUS module connector! Improper connection can cause permanent damage to Bluetooth/Interface module.
Connection diagram - Bluetooth and Satellite inputs CarStream Module (front) CarStream Module (back) Vehicle Connector Use Legacy SIRIUS SCC1 Tuner or SiriusXM Vehicle Tuner (Not included) VEHICLE TUNER IR Receiver (optional) Adapter cable AACCSATCBL (optional) Upgrade Port Bluetooth Module USB to PC or MAC computer *Do not connect the Bluetooth module under any curcumstance to the SIRIUS connector! Improper connection will cause permananet damage to the Bluetooth / Interface module.
Installation 1. Verify compatibility 5. Route kit to glove box or other accessible location 2. Disconnect battery 3. Locate factory Satellite Radio harness 6. Connect Bluetooth module 4. Set DIP switches to match factory radio type and install car specific harness OFF ON Continue on next page.
7. Mount the microphone in a suitable location as per the illustration. Use the included 2-sided tape or the clip. Make sure the microphone is directly facing the drivier. 8.
Controls and Indicators 1 2 3 1. Light Ring Unlit - unit is off. Red - unit is disconnected. Blue - unit is connected. Alternating red and blue - unit is in pairing mode. 2. Multi-Function Button 3. Built-In Microphone 4 4. Off / On / (Bluetooth) Switch Slide down to OFF to turn the unit off. Slide up to ON to turn the unit on. Slide up to to initiate pairing mode.
Bluetooth / AUX operation: Much like the radio’s AM/FM tuner or CD player, CarStream is integrated to be part of the factory audio system. 1. Select SAT mode using the source selector button. The display will show ‘BCS1’. At this time the AUXILIARY INPUT PORT OF THE CARSTREAM MODULE is enabled. Phone call or Bluetooth music streaming will automatically take over the AUX input.
Satellite operation: While the factory Satellite radio retention is not supported with this model, it is possible to add a Sirius SCC1 or a SiriusXM SXV200 / SXV300 vehicle tuner to the CarStream kit. Here’s how to access satellite radio: Select the SAT input source. Use your radio as described below and also in its owner’s manual for Satellite Radio operation. Using the seek buttons or knob will change stations, the CAT button will change categories. The presets can store and recall saved channels.
Important Note: Adding SiriusXM SXV200/300 vehicle tuner to Audi NAV+ and Volkswagen Navigation units is not supproted at the time of printing. Only Bluetooth calling and music streaming will function on these Navigation units. If retention of the factory satellite radio tuner is desired, we recommend using the CarStream BT101AVW or BT102AVW kit.
Pairing Your Phone Your mobile phone can initiate a search for the BCS1M. Note: The following procedures are generic. Procedures for pairing mobile phones may vary. Please refer to the manual that came with your mobile phone. 1. Turn the BCS1M on and slide the button slider up to the (Bluetooth) position. The light bar will flash red and blue alternatively. 2. Access the mobile phone’s Bluetooth function and turn the function on. 3. Set the mobile phone’s Bluetooth discover mode to on. 4.
Operation Activating Voice Assistant (Siri / Google Voice / Voice Dial) To activate the Voice Assistant feature of the mobile phone (if available), press and hold the multi-function button for 2-3 seconds . and then release it. Compatible Apple iPhone 4S or later model will trigger a Siri session. Google Voice may be available on select Android phones. Feature must be enabled on phone. Managing Phone Calls To make a call: Place calls as you normally do on your phone.
Managing Multiple Calls/Call-Waiting To answer a second incoming call: Tap the multi-function button three times to reject the call. To switch between two calls: Double-tap the multi-function button. To end the call on hold: Tap the multi-function button three times. To end the second call: Double-tap the multi-function button. Tap the multi-function button to end the current call.
Music Controls To play music: Tap the multi-function button. Your phone will play whatever music was last playing. You may need to start the music application on the mobile device the first time. To change the music selection, use the controls on the phone. Note: Some phones may require you to tap the button to put the phone into music mode. To pause/ resume the music: Tap the multi-function button. The music will pause. If the music is already paused, tap the multi-function button to play it .
Online Audio Streaming Services If you use audio-streaming services or apps such as Pandora® or iHeart Radio®, you may be able to use the BCS1M to enjoy streaming audio through your car stereo. However, not all phones or audiostreaming services support this feature. If the sound comes out of your phone instead of the car speakers: 1. Check to make sure the phone is connected to the BCS1M. 2.
Auxiliary audio source (only with optional AUX connector) The AUX cable (A-ACC-106-AUX) can be used to connect an auxiliary device, such as an MP3 player, DVD player or other audio source. The auxiliary audio source can be accessed in both CDC and SAT emulation modes. To access AUX audio source: - Plug the mini DIN connector of the AUX adapter cable into the SIRIUS receptacle and connect the 1/8” mini stereo jack to the sound output of your audio device.
Optional Remote Kit: Operation with Satellite radio tuner Toggle the audio sources between iPod and SIRIUS/AUX Next Category Previous Category Next Channel Recall preset SIRIUS channel Previous Channel Note: To display SIRIUS ID, go to channel 000. Save the current SIRIUS channel in the corresponding preset. Note: Saving presets with the remote will be different from the presets saved by the radio.
Troubleshooting You can quickly solve most problems with your BCS1M by following the advice in this section. Problem Solution The audio is not coming out of the stereo speakers. Make sure both the car stereo and BCS1M are powered on. Trouble with pairing Make sure your phone’s Bluetooth is turned on and set to search mode. Make sure the stereo volume is set to a confortable listening level. Make sure that your Bluetooth-enabled device is connected via Bluetooth to the BCS1M.
Problem Sirius tuner can’t be selected. Solution Ensure the cable connecting SIRIUS tuner is securely connected to the correct receptacle. Verify using the Audiovox OEI firmware apdater application that the interface module is properly set to work with the Satellite radio tuner type. Cannot select the interface. Verify the cable connections. Double check the DIP switch settings. Verify the firmware version using the Audiovox OEI firmware updater.
(Mac OS illustrated) Step 1. Download the Audiovox OEI firmware updater Consumer version can be accessed. at www.audiovoxoei.com/firmware Dealer updater can be accessed at www.voxxuniversity.com . Consumer version of the firmware updater requires the interface module to be registered. Installers, please use the dealer updater located at www.voxxuniversity.com Step 2.
(Mac OS illustrated) Step 3. Follow the on-screen instructions for the update Audiovox Firmware Updater v3.0.0 Audiovox Firmware Updater v3.0.0 Silverline DUO Audiovox DUO AVW ABP 2.01 DUO Audiovox Electronics Audiovox Electronics, Connect module via mini USB License Agreement (click Agree to proceed) http://secure.audiovox.net/audiovox/register/ Firmware update progress The above screen shots are for illustration purposes only.
12 MONTH LIMITED WARRANTY VOXX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company’s option) without charge for parts and repair labor.
Compliance Information FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
www.voxxelectronics.com © 2015 VOXX Electronics Corporation, 150 Marcus Blvd.
