VOH-641Drop Down Video Monitor VOH-642 Drop Down TV / Video Monitor ON OFF AUTO OPEN Installation Guide
Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly to the operator of the motor vehicle. Please note that the state of Rhode Island forbids the installation of such a device in a motor vehicle.
MATERIALS INCLUDED IN THIS PACKAGE: 1) 2) 3) 4) 5) 6) VOH-641 Video Monitor with out TV Tuner / VOH-642 Video Monitor with TV Tuner (1 pc) Accessory Harness (P/N 8010730) (1 pc) 12 Pin Power / Signal harness (P/N 112B2821) (1 pc) 2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc) RCA “Y” Adapter (1 Male to 2 Female) (P/N 0892165) (1 pc) Hardware Package #4 x 3/8” Screws (12 pcs) #8 x 5/8” Self Drilling Screws (4 pcs) #8 Washers (4 pcs) 7) Remote Control (P/N 1361612 supplied with VOH-642 only) 8) Pr
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Tuner, RF Modulator/external amp, remote headphones, 2nd VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting.
VEHICLE PREPARATION: 1) 2) 3) 4) Locate a constant power source (+12v at all times) and an accessory power source (+12v when key is in the acc. and run positions, and 0v when key is off). Generally, these wires can be found at the ignition switch or fusebox. The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories.
MINI CONSOLE INSTALLATION: This page only covers special installation considerations for the mini console installation. If the video monitor is to be installed with a custom full sized overhead console, refer to page 3. If the video monitor is to be installed in a vehicle with the mini console (part number 1181300), this console may need to be trimmed to fit the contour of the vehicle headliner.
MOUNTING THE MINI CONSOLE Roof Roof support Headliner 5"x9"x3/4" Plywood Block (4) #8x1" self drilling screws (not supplied) Mini-Console Video unit (4) #8 Flat washers (not supplied) (4) #8x3/4" self tapping screws (not supplied) -5-
VOH-641 Note: cables exiting the pod should be routed as shown. Wireless FM Modulator Antenna Power Harness 4 Item # 3a Red: +12 VDC (Accessory Cir.) Mini-Din Connectors choke Black: Ground Optional Hard Wired FM Modulator Output 2 12 VDC Power and Ground TO FACTORY RADIO Am/Fm Antenna Dash Radio FM Modulator 1070610 LEFT WHITE Patch Cord RIGHT RED Right *Refer to Instructions with the RF Input Modulator Kit for further details.
VOH-642 Note: cables exiting the pod should be routed as shown. Wireless FM Modulator Antenna Red: +12 VDC (Accessory Cir.) Power Harness Item #4 3a Mini-Din Connectors choke Black: Ground TV antenna (If applicable) Optional Hard Wired FM Modulator Output 2 12 VDC Power and Ground TO FACTORY RADIO Am/Fm Antenna Dash Radio Left Input 1 RCA-Female FM Modulator 1070610 Patch Cord LEFT WHITE RIGHT RED Right *Refer to Instructions with the RF Input Modulator Kit for further details.
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light.
Negative Switched Dome lighting To 12 pin connector on Monitor Red / black - Lamp on Black / red - Lamp common Purple / brown - Lamp Auto To constant +12vdc Factory Dome light circuit To constant +12vdc Factory Door ajar switch or Body Control computer Troubleshooting: Symptom: Remedy: No power at Video Monitor -Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor.
1999 Audiovox Corp. 150 Marcus Blvd.