-- CD 0;' :0; f ,1 °i WARNING: MICRO SYSTEM TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
-,."..~ .&:. This a contains low product power laser device. FCC INFORMATION This device complies with Part 15 of FCC Rules. Operations is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation.
".=-,:C',"~:'~ ! ON PLACEMENT .Do not use the unit in places which are extremely hot, cold, dusty, or humid. .Place the unit on a flat and even surface.Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by placing it on a carpet ON AC VOLTAGE .Before use, check that the rated voltage of your unit matches your local voltage. " " 1. 2. 3. 4. 5. 6. 7. CD display REMOTE SENSOR PLAY/PAUSE..u button STOP.
BATTERIES WHEN USING WITH BATTERIES Disconnect the AC power cord from the AC inlet of the unit. Battery power is cut automatically while the cord is connected. BATTERY REPLACEMENT When the volume decreases, or the sound distorts, replace all batteries with new ones.
",,=~I ~. TO RECEIVE THE FU BROADCAST IN STEREO Set the BAND selector to FM ST. When the FM STEREO STEREO indicator lights up. broadcast is received. IF THE FU STEREO BROADCAST SIGNAL IS WEAK Set the BAND selector to FM and background noise will be reduced but the broadcast monaural. AFTER LISTENING Set the FUNCTION selector to TAPE/STD-BY .
5
6
1. Sella 2. Insert TAPE (Exposed the cassette. side down) 3. Press the ~ PLAY button. PLAY FUNCTION CD . I~ tTAPE STD-8V 1!) TO FAST WIND Press Ihe ~ REWIND TO STOP PLAYBACK Press the STOP I EJECT button. TO INTERRUPT PLAYBACK Press the" PAUSE button. To resume play, press the" button again. or ~ F.FWD button. Press Ihe ./~ STOP I EJECT button 10 slOp winding allhe desired posllion.
.USE ONLY NORMAL (TYPE I) TAPES TO STOP RECORDING Press the .,~ STOP/EJECT FOR RECORDING. button. TO INTERRUPT RECORDING Press the II PAUSE button. To resume recording, press the II PAUSE TO ERASE A RECORDED TAPE 1. Set the FUNCTION selector to TAPE. 2. Insert a tape with the side yoU want to erase facing 3. Press erasing. button again. 8 yoU. the.
" ,~: -, '.' .STOP ~~ HI SKIP PLAY/PAUSE PROGRAM REPEAT ONE/All INSTALLING BATTERIES Install two 1.5V , RO3 (AAA or SUM-4) size batteries into the battery compartment Controller. of the Remote BATTERY REPLACEMENT When batteries become weak, the operating distance of the Remote Controller reduced and the batteries will need to be repiaced. will be greatiy USING THE REMOTE CONTROLLER CORRECTLY Point the Remote Controller at the REMOTE SENSOR located to the right of the CD dispiay window.
CLEANING CD If the CD skips or cannot be played, the disc may need cleaning. Before playing, wipe the disc from the center out with a cleaning cloth. After playing, store the disc in its case. ~ CLEANING THE TAPE HEADS To maintain optimum sound quality, clean the playback/record heads (a), erasure head (b), pinch rollers (c), and capstans (d) regularly (every 10 hours of use), using a cotton swab lightly moistened with cleaning fluid or denatured alcohol.
CASSETTE SECTION Track format: Signal to noise radio Recording system: Erasing system: Tape speed: F.F. & REW time: Frequency response: Motor 4 track stereo 2 channels 40 dB (Normal tape) AC bias Magnetic erase 4,75 cm I sec. 110 sec. (C-60 tape) 125 -8,000 Hz (normal tape) DC motor x 1 CD SECTION Channels: SIN ratio: Quantization: Pick up light source: Pick up wave length: Rotation Speed: 2 channels 60dB 1 bits linear/ch Semiconductor laser 790 nm Approx.
