INTRODUCTION It is important you read this manual (USER’S GUIDE) before using your device ( to ensure its proper operation. Pocket PC) It is recommended that important data stored in your device should be saved to a memory card (sold separately) or your personal computer (data transfer with ActiveSync®) on a regular basis. Before returning your unit for service, be sure to back up your data and remove any confidential, proprietary or personal information. Audiovox Communications Corp.
Product Name: Model Number(s): CET0200A (PDA2032) FCC Notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Product Name: USB Cradle Model Number(s): CEX0208B (CRU2032B) FCC Notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS • There are two categories of Safety Instructions included in this manual: ✓ Product Warnings, (i.e., what must never be done to assure avoiding those hazards that could cause bodily injury or property damage); and ✓ User Directions (i.e., what must always be done to assure the safe use of your device). • The Safety Instructions contained in this manual have been categorized in accordance with the seriousness of the potential hazards through the use of Signal Words.
SAFETY INSTRUCTIONS WARNING ■ Never use your device while driving an automobile or any other moving vehicle. Always pull out of traffic and come to a stop in a legally permissible and safe location before using your device. Failure to do so could result in serious bodily injury in a traffic accident. ■ Never use your device while walking. Usage while walking could result in bodily injury caused by inattention to automobile traffic or other pedestrian hazards.
SAFETY INSTRUCTIONS the eyes or skin, could cause injury to the skin or eyes. Should the liquid come into contact with the eyes, irrigate the eyes thoroughly with clean water and immediately seek medical attention. In the event the liquid comes into contact with the skin or clothing, wash it away immediately with clean water. Failure to follow the above directions concerning use and storage could result in bodily injury and/ or property damage due to battery liquid leakage, fire or rupture.
SAFETY INSTRUCTIONS ■ Use of your device in locations where the following ambient environmental conditions are exceeded: ✓ Under normal operational use ambient temperatures not less than 32°F and not in excess of 104°F (0°C and 40°C); ✓ With humidity of not less than 30% or in excess of 80%; and ✓ When charging the battery ambient temperatures not less than 41°F and not to exceed 95°F (5°C and 35°C).
SAFETY INSTRUCTIONS ■ When the device is operating, do not insert or remove the “SD memory card” into or out of the SD card slot or connect or disconnect the device from the cradle as this may cause loss of stored data, or product failure/malfunction. ■ Never connect cradle terminals with metallic objects, such as wires. Connecting these terminals with metallic objects may cause the production of excess heat, burns and damage to the charger and/or your device.
SAFETY INSTRUCTIONS Safe Use of AC Adapter DANGER ■ Never attempt to disassemble or repair an AC Adapter, and never alter the power cords or plugs as exposure to electric shock hazards may result. Always contact an authorized Audiovox service center, if repair or replacement is required. ■ If the plug will not fit into the available outlet, have a proper outlet installed by a qualified electrician. Improper connection can result in the risk of electric shock.
SAFETY INSTRUCTIONS CAUTION ■ Never place an AC Adapter on a wooden surface (or any other surface that could be marred by exposure to heat) while it is in use. Since its surface temperature of the AC adapter increases during normal use, always rest it on a suitable heat-insulating material. ■ Never cover the AC Adapter with any object while it is in use, and never place it adjacent to a heat source. An excessive temperature increase could detrimentally affect its performance.
SAFETY INSTRUCTIONS SAFE USE AND OPERATION OF DEVICE (WIRELESS HANDHELD PHONE) Read this information before using your device. Your device is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radiofrequency (RF) signals.
SAFETY INSTRUCTIONS Tips on Efficient Operation: For your phone to operate most efficiently: • Do not touch the antenna unnecessarily and keep the antenna from metal when the phone is in use. Contact with the antenna affects call quality and may cause the phone to operate at a higher power level than otherwise needed. WARNING DRIVING Never use a device and/or cell phone while driving an automobile or any other moving vehicle.
SAFETY INSTRUCTIONS Posted Facilities Turn your device OFF in any facility where posted notices require so. AIRCRAFT FCC regulations prohibit using your device while in the air. Turn your device OFF before boarding an aircraft. BLASTING AREAS To avoid interfering with blasting operations, turn your device OFF when in a “Blasting area” or in areas posted “Turn off two-way radio”. Obey all signs and instructions.
SAR Information SAR Information Specific Absorption Rate THIS MODEL PHONE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population.
Table of Contents SAFETY INSTRUCTIONS ............................................................................................................ 5 SAFE USE AND OPERATION OF DEVICE (WIRELESS HANDHELD PHONE) .......................................................................... 12 SAR Information ........................................................................................................................ 15 Chapter 1: Getting Started .........................................................
Speed Dial ................................................................................................................ 70 Call Log..................................................................................................................... 71 Options (Preferences)............................................................................................... 72 SMS (Messaging) .....................................................................................................
Chapter 1: Getting Started Chapter 1 Getting Started 18
Chapter 1: Getting Started Welcome Congratulations on the purchase of your Pocket PC. You can keep your most important business and personal information up to date and close at hand. And with the power of Microsoft® ActiveSync® you can synchronize and download information on your desktop or laptop computer with your handheld device. With your Pocket PC you can: • Make and receive phone calls. • Instantly view the day’s appointments with the touch of a button. • Send and receive e-mails.
Chapter 2 Basic Skills
Chapter 2: Basic Skills Parts Names and Function Main Unit (front view) Incoming Call / System Notification LED Charging LED Power Button / Front Light Button Microphone Fixed Antenna Record Button (Program Button 5) Radio Standby Switch Program Button 1, 2, 3 & 4 (From the Left) SEND Button END Button Touch Screen Speaker AC Adapter Jack Cradle Connection Port Cursor Button / Navigation Button The Cradle USB Cradle Initial Setting of Program Buttons Program button 1 ........
Chapter 2: Basic Skills Main Unit (back view) Stylus Holder Headphone Jack SD Card Slot Stylus Hand Strap Attachment Reset Switch Infrared Port Color Panel 22
Chapter 2: Basic Skills Power Button / Front Light Button Press this to turn the device and the front light on/off. Power button When the power is off When the power is on Press and hold. Press it quickly. The power turns on. The power turns on. The front light alternately turns on/off. The power turns off. Even if the power is turned off, pressing the program button turns the power on and the program screen is displayed. (However, you can change the setting.
Chapter 2: Basic Skills 3. Reattach the Color Panel. Note Returning the switch to the “Stop” (the upper side) resets the device back to its factory settings - initial setup will need to be repeated. To move to the “Stop” side, slide the switch while inserting the stylus into the Battery Switch Lock. Charging LED • Steady orange .............. Built-in battery charging • Flashing yellow ............. Charging has stopped due to extreme temperatures.
Chapter 2: Basic Skills About Cursor Button Navigate the cursor on screen by pressing the upper, lower, right or left part of the cursor button. Press the center of the button to select an option or program. Note The cursor movement depends on the screen. When the cursor is at the right or the left side of the screen, it may not move. Earphone Microphone The supplied Earphone Microphone can be used to receive phone calls.
Chapter 2: Basic Skills Audio Remote Controller with Microphone The supplied Audio Remote Controller with Microphone can be used to listen to audio playback. Combined with the headphone (sold separately), it can be used to receive phone calls. When the Audio Remote plug is inserted into the device, the microphone and speaker on the main unit will become inactive. Also, this microphone can be used as a recorder.
Chapter 2: Basic Skills Battery Charging When using the device for the first time, set the Battery Switch to the supply side (see page 23), then fully charge the battery. Charging the Battery You can use two charging methods. When you connect the AC Adapter to the device, turn the power off. • Connect the supplied AC Adapter to the cradle as shown in the figure below, and then insert the device into the cradle. • Connect the supplied AC Adapter to the device as shown in the figure below.
Chapter 2: Basic Skills Maximizing the Battery Operating Time • Whenever possible, use the device with the AC Adapter – especially when it is connected to your computer. • Select the short powered-off time in the setting menu. This will shorten the time the unit will remain on if not used. See “Customizing Your Device” later in this chapter for more information. • • Turn off the front light. • For optimal performance use in an environment between 59°F - 77°F (15°C and 25°C).
Chapter 2: Basic Skills Initial Setup When using your device for the first time, completely charge the battery then follow the initial setup procedures below: 1. Press the Power button and when the welcome screen appears, tap the screen with the stylus to start the setup process. 2. When the align screen appears, follow the directions for adjusting the touch screen until the stylus screen appears. • If a finger or any other object touches the screen during a correction, it will be cancelled.
Chapter 2: Basic Skills Setup Options Method of Setting Card into SD Card Slot Inserting a card: 1. Turn off the power. 2. Insert the card with its contact surface (metal contact surface) facing backward into the device. Contact surface Note An SD dummy card is loaded in the SD card slot at purchase. Remove the SD dummy card before inserting the card. Removing a card: 1. Make sure that no application is accessing the SD card. 2. Turn off the power. 3.
Chapter 2: Basic Skills Connecting to a Computer Before connecting your device to a computer, check the following. • ActiveSync® is on your computer. (For installation procedures of ActiveSync®, see Quick Start Card.) • The device is turned off. • The computer you’re connecting has an available USB port for the cradle. To connect using the supplied USB cradle: 1. Connect the USB cradle to your computer as shown in the illustration below. USB port 2. Insert the device into the USB cradle.
Chapter 2: Basic Skills Today Screen The Today screen appears when you turn on your device after 4 hours of inactivity. It can be accessed by tapping and then Today. Tap to switch to a program. Tap to change date and time. Tap to open information setting. Your day at a glance. Tap to create a new item. 32 Tap to view connection status.
Chapter 2: Basic Skills Following are some of the status icons you may see.
Chapter 2: Basic Skills Programs Switch from one program to another by using the menu. To access programs not listed on the drop down menu, tap , Programs, then the desired program. You can also switch to another program by pressing any of the five program buttons located on the front and side of the device. The icons above the buttons identify the factory set programs (from left to right) – Calendar, Tasks, Home and Contacts. The Record button on the side is for voice recording.
Chapter 2: Basic Skills Navigation Bar and Command Bar The navigation bar, located at the top of the screen, displays the active program and time, and allows you to switch programs and close screens. The command bar at the bottom of the screen performs tasks in the open program, and includes menu names, buttons and the Input Panel button. Tap New to create a new item in the program. Tap to view notification messages. Tap to change volume or mute the device.
Chapter 2: Basic Skills Pop-up Menus Pop-up menus provide quick access to select an action for an item, and vary with each program. To access a pop-up menu, tap and hold the stylus on the item you want to perform the action on. When the menu appears, lift the stylus and tap the desired action. Tap anywhere outside the menu to close it. Tap and hold to display the pop-up menu. Lift the stylus and tap the action you want. Tap outside the menu to close it without performing an action.
Chapter 2: Basic Skills Entering Information Options for entering new information include: • Using the input panel to enter typed text. • Writing or drawing pictures directly on the screen. • Recording a message by speaking into the microphone. • Using Microsoft® ActiveSync® to synchronize or copy information from your computer to the your device.
Chapter 2: Basic Skills When you use the input panel, your device anticipates the word you are typing or writing and displays it above the input panel. When you tap the displayed word, it is inserted into your text at the insertion point. The more you use your device, the more words it learns to anticipate. Tap here if this is the right word. Note To change word suggestion options, such as the number of words suggested at one time, , Settings, Personal tab, Input, and then the Word Completion tab.
Chapter 2: Basic Skills Using Block Recognizer: With Block Recognizer you can use the stylus to input character strokes similar to those used on other devices. 1. Tap the arrow next to the Input Panel button and then Block Recognizer. 2. Write a letter in the box — it will automatically be converted to typed text on the screen. For specific instructions, open Block Recognizer and tap the question mark icon next to the writing area.
Chapter 2: Basic Skills Writing on the Screen To write on the screen, write the same way do on paper. The text can be edited, formatted or converted at a later time. Writing on the screen: • To switch to the writing mode, tap the Pen button. Lines will appear on the screen to help you write. Tap the Pen button and use your stylus like a pen. Note Not all programs that accept writing feature the Pen button. Refer to that program’s documentation to find out how to switch to writing.
Chapter 2: Basic Skills Converting writing to text: • Tap Tools and then Recognize. If you want to convert only certain words, select them before tapping Recognize on the Tools menu (or tap and hold the selected words and then tap Recognize on the pop-up menu). If a word is not recognized, it is left as writing. Select the text you want to convert and tap Recognize on the pop-up menu. The writing is turned into text.
Chapter 2: Basic Skills If the word conversion is incorrect, you can select an alternative word by tapping and holding down on the wrong word. On the pop-up menu tap Alternates and browse the list. Either tap the word you want to use, or tap the writing at the top of the menu to return to the original writing. Tap to return to your original writing. Or, tap the word you want to use. For best recognition: • Write neatly within the lines and draw descenders below the line.
Chapter 2: Basic Skills Drawing on the Screen Draw on the screen in the same way that you write on it. The only difference is how the items are selected and edited. For example, drawings can be resized - writing cannot. Creating a drawing: • A drawing box will appear when you cross any three ruled lines on your first stroke. Subsequent strokes in or touching the box become part of the drawing. Drawings that do not cross three lines will be considered writing.
Chapter 2: Basic Skills Recording a Message A message can also be recorded on any program where you can write or draw on screen. In Calendar, tasks and Contacts, you can include a recording in the Notes tab. In the Notes program, you can either create a stand-alone recording or include a recording with a written note. With the Inbox program a recording can be added to an e-mail.
Chapter 2: Basic Skills Using My Text My Text quickly inserts preset and frequently used messages into the text entry areas of Inbox or MSN® Messenger. To insert a message, tap My Text and select a message. Tap to select a prewritten message. Note You can add text after inserting a My Text message. To edit a My Text Message, tap Edit My Text Messages in the Tools menu. Select the message you wish to edit and make the changes. Tap OK in the upper right corner to complete the change.
Chapter 2: Basic Skills Finding and Organizing Information To quickly locate information using the Find feature, tap Find in the menu. Note To quickly find information that is taking up storage space on your device, select Larger than 64 KB in Type. File Explorer can also find files on your device and organize them into folders. To access from the menu, tap Programs, then File Explorer. Tap to change folders. Select the sort order for the list. Tap the folder name to open it.
Chapter 2: Basic Skills Customizing Your Device Customize your device by adjusting the settings and installing additional software. Adjusting Settings Settings can be adjusted by tapping , Settings, and then the Personal or System tab located at the bottom of the screen. The following settings can be adjusted: • Clock: To change the time or to set alarms. • Menus: To customize what appears on the menu from the New button.
Chapter 2: Basic Skills Adding or Removing Programs Programs installed on your device at the factory are stored on ROM (read-only memory) and cannot be removed or accidentally lost. ROM programs can be updated using special installation programs with a *.xip extension. Any programs and files added after factory installation are stored in RAM (random access memory). As long as you have enough memory, you can install any program created for your device.
Chapter 2: Basic Skills Adding a program directly from the Internet: 1. Determine which version of the software to install by tapping , then Settings. On the System tab, tap About. In the Version tab, make a note of the information in Processor. 2. Download the program to your device straight from the Internet using Pocket Internet Explorer. You may see a single *.xip, *.exe or *.zip file, a Setup.exe file, or several versions of files for different device types and processors.
Chapter 2: Basic Skills Setting Password Protect data and settings by choosing a password that will be requested every time the power is turned on. 1. Tap , then Settings. On the Personal tab, tap Password. 2. Select the type of password you would like to use. Your password must be four numerals. Your password must be at least seven characters long and contain a combination of uppercase letters, lowercase letters, numerals or punctuation.
Chapter 2: Basic Skills Setting the Front Light 1. Tap , then Settings. On the System tab, tap Front Light. 2. Set the Front Light. Check and select when you want front light to automatically turn off. Sets the time that elapses until the front light automatically turns off. Automatically turns the front light off when the AC Adapter (external power) is in use. Tap to select brightness level. If Power Save is activated, the front light turns off. 3. When finished, tap OK.
Chapter 2: Basic Skills Setting Power To confirm and control power usage: 1. Tap , then Settings. On the System tab, tap Power. 2. Set Power Options. Displays remaining battery power. When the AC Adapter is used, the battery charging mode is displayed, but the remaining battery power is not displayed. When checked, automatically turns off when the device hasn't been used for a user-set amount of time. Sets the time that elapses until the power automatically turns off.
Chapter 2: Basic Skills Setting Memory Memory for the device is automatically managed. You can adjust data storage memory and program running memory, and confirm the amount of free space on a storage card. Changing memory allocation: 1. Tap , then Settings. On the System tab, tap Memory to display the Memory setting screen. Slider. Free space of the Program memory. Free space of the Storage memory. 2. Drag the slider widthwise to adjust the memory allocation between Storage and Program. 3.
Chapter 2: Basic Skills To confirm usage status of a storage card: 1. Tap , then Settings. On the System tab, tap Memory, then the Storage Card tab on the bottom. Capacity of a storage card being inserted. Free space. Capacity in use. 2. When finished, tap OK. Releasing memory: If memory is approaching full capacity, you can free up space by: • Transferring data to a storage card or to your computer then delete it from your device. • Deleting unnecessary files and programs.
Chapter 3 Phone Phone Functions Functions
Chapter 3: Phone Functions This device’s phone component can be used with the Earphone Microphone or as a speakerphone. Unlike conventional cell phones, it is not designed to be held against the head in conversation. Such unauthorized use of the phone, without an Earphone Microphone or other than as a speakerphone, is contrary to the design of this product and is not recommended. For instructions on how to use the phone with Earphone Microphone or as a speakerphone, please refer to page 61 of this manual.
Chapter 3: Phone Functions Main Screen DATA tab In Use Indicator. Receiving Signal Strength Indicator. Coverage Indicator Icons. Receiving Signal Strength/No Service Indicator. Status box displays information about the current call and any status messages. Indicator icons. Connection Drop-List. Phone number of the connection destination. Shortcut to Dial-up Manager. Data/Voice Controls Tab Selection. VOICE tab Call progress indicator. Incoming or Outgoing number and cross-referenced Phone Book name.
Chapter 3: Phone Functions Icons Icons of the display indication Icon Meaning Auto-Answer incoming Voice Calls Unread message waiting - flashes when message is set to high priority. One or more voice mail messages One or more missed calls Earphone connected to the device When receiving a call, the ringer tone sounds and the vibrating alert vibrates simultaneously. When receiving a call, the ringer tone does not sound but the vibrating alert vibrates.
Chapter 3: Phone Functions Keypad Operation List Regardless of the program in use, pressing the SEND button or the END button while Watcher is open displays the VOICE tab of the Watcher screen. Even if the power is turned off, pressing the SEND button turns the power on and displays the VOICE tab screen. (However, the setting can be changed not to turn the power on.) When the Watcher screen is displayed, the SEND/END buttons on the device perform the same functions as the SEND/END buttons on the screen.
Chapter 3: Phone Functions Tools menu: The following items can be selected from the Tools menu of the DATA and VOICE tabs: Displays the Messaging screen. Displays Phone Book. Displays screen for storing numbers. Displays a list of incoming calls, outgoing calls, missed calls. Displays the Connections setting screen. Protects against accidental operation. Displays Options for changing settings.
Chapter 3: Phone Functions Talking on the Phone Here explains how to use your device when you talk on the phone. Keep the device from your face more than 1 inch (2.5 cm). Using the Microphone and Speaker: Using the Earphone Microphone: To use the supplied Earphone Microphone, insert it into the headphone jack. For the Earphone Microphone, see page 25 of Chapter 2.
Chapter 3: Phone Functions Placing Calls To place a call, Watcher must be launched. Dialing 1. On the VOICE tab screen, use the dial pad to enter the phone number and tap SEND. appears when the call is connected. Call is connected. Note If a mistake is made while dialing, tap CLR to clear the last digit, or END to clear the entire number. Ending a Call 1. Tap END to end a call. The call time will disappear from the screen.
Chapter 3: Phone Functions Dialing from the Phone Book 1. To access Phone Book either tap Tools menu. on the VOICE tab screen or tap Phone Book on the 2. Select the phone number you wish to call, then tap Dial on the command bar. when the call is connected. appears Note Dial can be found in the pop-up menu that appears when you tap and hold a phone book entry. Double tapping the desired phone number also places the call. Speed Dialing 1.
Chapter 3: Phone Functions Receiving a Call Depending on the settings, an incoming call is alerted with an audible sound, a flashing indicator, or a vibrating alert. 1. To answer a call, tap the SEND button on the device or the screen. Tapping CLR or the Volume button can mute the ringer tone. About Any-key Answer: • When activated, Any-key Answer enables calls to be answered by tapping any button, other than the END, CLR or Volume buttons.
Chapter 3: Phone Functions Volume Control Adjust the ringer volume by using the Speaker Icon on the navigation bar and the call volume (the speakerphone volume) by using the Volume buttons. Tap to adjust the ringer volume. Appears when Volume buttons are used. Speaker Icon button. Volume buttons. Speaker Icon button: The ringer type changes each time you tap the Speaker Icon button.
Chapter 3: Phone Functions Call Waiting When you’re on the phone and another call is received, you hear a call waiting tone and “Call Alert From” appears on the display. 1. Tap SEND to put the original party on hold and switch to the new caller. When speaking to the new caller, the information for the first caller will not be displayed. 2. Tap SEND to switch to the original caller. Call Forwarding Call Forwarding transfers incoming calls to another phone number.
Chapter 3: Phone Functions Missed Call appears if you do not answer a call. Tap END to turn off the missed call message. Returning Missed Calls To return the last missed call, tap SEND. When is tapped, the Call Log appears. This can be used to select a contact to call back. For details on the Call Log function, see page 71. Note If the caller’s number is not identified, you cannot call back.
Chapter 3: Phone Functions Emergency Dialing Emergency calls can be placed - even if the phone is not registered or activated, or KeyGuard is activated -- as long as the power is on and there is a signal. 1. Enter “911” from the dial pad and tap SEND. 2. Tap END to end the call. Note If an emergency number is stored in Speed Dial you will be able to dial it by pressing a single key. However, speed dial will not work if KeyGuard is enabled. The emergency call number varies from region to region.
Chapter 3: Phone Functions KeyGuard Lock This function guards against accidentally inputting numbers or pressing unwanted keys. To enable from the VOICE tab screen: 1. Tap Tools, then KeyGuard. “KeyGuard enabled” appears on the screen. 2. Repeat the same process to turn KeyGuard off. Note When KeyGuard is enabled, the only functions that can be performed are selecting the Tools/Admin menus, placing emergency calls, receiving incoming calls (by tapping SEND), and turning the KeyGuard mode off.
Chapter 3: Phone Functions Speed Dial Using speed dial simplifies calling. Storing 1. To access speed dial list, tap Speed Dial on the Tools menu or press left on the navigation button. 2. Tap the area next to the dial pad number where you want to store a phone number, and the Phone Book screen appears. 3. Select the contact you want to store, then tap Add on the command bar. 4. Tap OK. Tap to call to the phone number in the right section. Clearing 1.
Chapter 3: Phone Functions Call Log Call Log screen displays a list of incoming, outgoing and missed calls, including caller information and call time. To display, tap Call Log on the Tools menu or press right on the navigation button. When you tap and hold a log entry a pop-up menu displaying Delete, Copy Phone Number and Dial. Adding Telephone Numbers From the Log 1. Tap and hold the contact name, when pop-up menu appears tap Copy Phone Number. 2. Tap , Contacts and New. 3.
Chapter 3: Phone Functions Options (Preferences) Tap Options on the Tools menu to display the Options setting screen. A number of settings (Security, Sounds, etc.) can be made at this screen. General Sets number of minutes a line is disconnected after data communication ends. (Display tab of Options can be set to display warning before line is disconnected.) Select the mode for answering incoming calls. Select the number of calls to be retained in the Call Log.
Chapter 3: Phone Functions Display Check to display the Warning Message while meeting the conditions on the right part.
Chapter 3: Phone Functions Messaging Sets options for short message services. Sets messages expiration dates. Check here then tap Change to display the Callback entry screen. Enter the phone number you want displayed as a callback number when a message is sent. Sets Outbox storage preference.
Chapter 3: Phone Functions Security Use Security tab to lock the modem or change the password. When the modem is locked, most menu functions (Options, Messaging, Call Log etc.) cannot be used. (The Unlock Modem menu can be selected.) Also, no calls other than emergency calls can be placed, and when a call is received, the caller’s ”. phone number is displayed “ *** The default of the lock code is the last four digits of the device’s phone number, if the phone is activated. Select never or on power up.
Chapter 3: Phone Functions Sounds Use to select the sounds for incoming calls, voice mail and SMS messages. When a box is checked that alert will sound. Tap “>” to play selected sound. Tap “...” to select a sound file. Select a receiving type from “Ringer Only”, “Ring and Vibe”, “Vibrate Only” and “Ring and Vibe Off” in the “Incoming Call” section. You can also select a receiving type with the Speaker Icon button on the VOICE tab screen. Adjust the volume of the conversation.
Chapter 3: Phone Functions Voice Determines when auto-answer function answers phone. Ideal to use while driving. Determines when to retry a call that did not connect. When checked, automatically adds hyphenation when phone numbers are entered on dial pad. When this is checked, incoming calls can be answered by pressing any key other than END, CLR and the Volume button. This function does not work in the KeyGuard mode. Sets the dial pad tone length. When checked, tone is not sounded.
Chapter 3: Phone Functions SMS (Messaging) Contact your service provider before using this function. Tap Messaging on the Tools menu to display the SMS message screen. appears on the display when you receive a message, flashing if it is high priority. Tap this indicator to open the SMS screen. The following is a list of the icons displayed with the SMS function. Icon Meaning High priority message. Saved, unsent message in the Outbox. Error occurred during transmission and message not sent.
Chapter 3: Phone Functions Inbox Received messages are stored in the Inbox. List of received messages. Unread messages displayed in bold. Time message was received. Sender’s phone number. Displays Callback number when the sender specified it. Message priority. Number of messages stored in the Inbox. Tap to compose a new message.
Chapter 3: Phone Functions Outbox Sent and unsent messages are stored in the Outbox. List of sent or saved messages. Icon displayed depends on message status - see page 78. Message status. Destination address. Set Callback number. Number of messages stored in Outbox. The following options can be selected from the File menu. Edit Message: Edits stored messages - overwriting previous message. New Message: Create a new message The following options can be selected through the Edit menu.
Chapter 3: Phone Functions Composing New Messages 1. At the Messaging screen, tap on the command bar. 2. Enter the recipient’s phone number or address with the input panel or by accessing the Phone Book by tapping To. (See the following page.) 3. Select Normal or Urgent for Priority. 4. Enter the message and press Send. If the message is successfully transmitted, the screen automatically closes. Note Selecting Send from the File menu also sends messages.
Chapter 3: Phone Functions Selecting recipients: 1. On the message screen, tap To. 2. Select the recipient from the list, then tap Add. Recipients can also be selected by continually double tapping the phone number or address. 3. After selecting recipients, tap OK. Enter contact not listed in Phone Book, then tap Add to include in Recipients. To remove a recipient, select the recipient and tap Remove. Displays recipients. Tap to return to previous screen.
Chapter 3: Phone Functions Accessing the Internet Access the Internet by selecting Circuit Switch Data or High Speed Data from the DATA tab or by using an ISP. High-speed packet service. Connection service allowing smooth connection to the Internet. 1. Tap the pull-down list and select the desired connection name. 2. Tap Connect to access the Internet.
Chapter 3: Phone Functions Using Subscribed Internet Service Provider (ISP): 1. Tap Dial-Up Manager on the Tools menu. The Connections setting screen appears. 2. Tap Add. 3. Enter the required information. Enter the connection name. (Example: ISP name) Enter the connection number. Enter the connection user name specified by the ISP. Enter the connection password.
Chapter 3: Phone Functions 4. Tap Save. The settings are now stored and can be accessed. Note After establishing the dial-up setting using the Sierra Wireless SB555 Modem by setting Connection of Settings, if you restart Watcher with Radio Standby Switch, you can also use the connection setting from the DATA tab screen. For more information on setting Connection of Settings, see “Connecting to the Internet” in Chapter 8. After the setting is entered, you can access your subscribed ISP.
Chapter 4: Microsoft® ActiveSync® Chapter 4 Microsoft ActiveSync ® ® 86 ® ®
Chapter 4: Microsoft® ActiveSync® Microsoft® ActiveSync® synchronizes the information on your computer with the information on your device. Synchronization compares data between the two and updates both with the most recent information. For example: • Keep Pocket Outlook® data up-to-date by synchronizing your device with your computer’s Microsoft® Outlook®. • Synchronize Microsoft® Word and Microsoft® Excel files between the two. Files will be automatically converted to the correct format.
Chapter 4: Microsoft® ActiveSync® After installation is complete, the ActiveSync® Setup Wizard will: 1. Help connect your device to your computer. 2. Set up a partnership to synchronize information between the two devices. 3. Customize the synchronization settings. Synchronization automatically begins when you finish using the Wizard. After this initial synchronization, view your device’s Calendar, Contacts and Tasks. Everything stored in Microsoft® Outlook® on your computer should now be on your device.
Chapter 5 Microsoft Pocket Outlook ® ® ® ®
Chapter 5: Microsoft® Pocket Outlook® Microsoft® Pocket Outlook® includes Calendars, Contacts, Tasks, Inbox and Notes which can be used individually or together. For example, e-mail addresses stored in Contacts can be used to address e-mail messages in Inbox. ActiveSync® synchronizes information in Microsoft® Outlook® or Microsoft® Exchange on your computer with your device, comparing changes made on both and updating each of them with the latest information.
Chapter 5: Microsoft® Pocket Outlook® Creating an appointment: If you are in Day or Week view, tap the desired date and time for the appointment. 1. Tap New. Tap to return to the calendar (the appointment is saved automatically). Tap to choose from predefined text. Tap to choose from previously entered locations. Tap to select a time. Tap to select a date. Notes is a good place for maps and directions. 2. Enter a description and location. 3. Adjust date and time as needed. 4.
Chapter 5: Microsoft® Pocket Outlook® Using the Summary Screen Tap an appointment to display the summary screen. To make changes, tap Edit. View appointment details. Display notes. Tap to change appointment. Creating Meeting Requests Calendar can set up meetings with Outlook® or Pocket Outlook® users. The meeting request will be created automatically and sent either when you synchronize Inbox or when you connect to your e-mail server.
Chapter 5: Microsoft® Pocket Outlook® Contacts: Tracking Friends and Colleagues Contacts maintains an easily accessible list of friends and colleagues (See note below). The device’s infrared (IR) port allows you to quickly share Contacts information with other device users. , then Contacts. Or, press the Contacts Program button on the front of To access Contacts, tap the device. Select the category of contacts you want displayed in the list. Tap and enter part of a name to quickly find it in the list.
Chapter 5: Microsoft® Pocket Outlook® Creating a contact: 1. Tap New. Tap to return to the contact list (the contact is saved automatically). Scroll to see more fields. Notes is a good place for maps and directions. 2. Enter name and contact information. Scroll down to see all available fields. 3. Tap Categories to assign the contact to a category. In the list, Contacts can be displayed by category. 4. Tap the Notes tab to add notes or a drawing, or to create a recording.
Chapter 5: Microsoft® Pocket Outlook® Using the Summary Screen Tap a contact to display the summary screen. To make changes, tap Edit. View contact details. Tap to view or add notes. Tap to change contact information.
Chapter 5: Microsoft® Pocket Outlook® Tasks: Keeping a To Do List Tasks keeps track of what has to be done. To access, tap Program button on the front of the device. , then Tasks. Or, press the Tasks Select the category of tasks you want displayed in the list. Select the sort order of the list. Indicates high priority. Tap to display or edit the task details. Tap and hold to display a pop-up menu of actions. Tap to create a new task.
Chapter 5: Microsoft® Pocket Outlook® Creating a task: 1. Tap New. Tap to return to the task list (the task is saved automatically). Tap to choose from predefined subjects. Notes is a good place for maps and drawings. 2. Enter a description. 3. Enter a start and due date or other information by tapping the field. To see all available fields, hide the input panel. 4. Tap Categories to assign the task a category. In the list, Tasks can be displayed by category. 5.
Chapter 5: Microsoft® Pocket Outlook® Using the Summary Screen Tap a task to display the summary screen. To make changes, tap Edit. View task details. Tap to show and hide additional summary information. View notes. Tap to change task.
Chapter 5: Microsoft® Pocket Outlook® Notes: Capturing Thoughts and Ideas Notes quickly captures thoughts, reminders, ideas and phone numbers. You can also create a recording to include with the entry. Tap to change the sort order of the list. Tap to open a note or play a recording. Tap and hold to display a pop-up menu of actions. Tap to record. Tap to show or hide the Recording toolbar. Tap to create a new item.
Chapter 5: Microsoft® Pocket Outlook® Creating a note: 1. Tap New. 2. Create your note by writing, drawing, typing, and recording. For more information about using the input panel, writing and drawing on the screen, and creating recordings, see “Entering Text Using the Input Panel” in Chapter 2. Tap to return to the note list (the note is saved automatically). Tap to show or hide the input panel. Tap to write on the screen. Tap to add a recording to the note.
Chapter 5: Microsoft® Pocket Outlook® Inbox: Sending and Receiving E-mail Messages Use Inbox to send and receive e-mail messages in either of these ways: • Synchronize e-mail messages with Microsoft® Exchange or Microsoft® Outlook® on your computer. • Send and receive e-mail messages by connecting directly to an e-mail server through an Internet service provider (ISP) or a network. Synchronizing E-mail Messages E-mail messages can be synchronized as part of the general synchronization process.
Chapter 5: Microsoft® Pocket Outlook® Using the Message List Received messages are displayed in the message list - the most recently received are listed first. Select the service and folder you want to display. Select the sort order for messages. Tap to open a message. Tap and hold to display a pop-up menu of actions. Tap to connect and to send and receive e-mail. Tap to connect to the selected service.
Chapter 5: Microsoft® Pocket Outlook® When you receive a message, tap it to open it. Unread messages are displayed in bold. Tap to return to the message list. Tap to delete this message. Tap to view the previous or next message. Tap to reply to or forward this message. To retrieve a full message during your next synchronization or e-mail server connection, tap and hold the message. On the pop-up menu tap Mark for Download.
Chapter 5: Microsoft® Pocket Outlook® Composing Messages 1. Tap New. 2. In the To field, enter the e-mail addresses of the recipients, separating the names with a semicolon, or select a name from the contact list by tapping and holding To, or by tapping the Address Book button. Tap to send the message. Tap to show or hide . the complete header. Tap to show / hide the recording toolbar. Tap to display the Address Book. Tap to insert common messages. 3. Compose your message.
Chapter 5: Microsoft® Pocket Outlook® Managing E-mail Messages and Folders Messages are displayed in one of five folders: Inbox, Deleted Items, Drafts, Outbox and Sent Items. The Deleted Items folder contains messages that have been deleted on the device. The behavior of the Deleted and Sent Items folders depends on the options you have chosen. In the message list, tap Tools then Options. On the Message tab, select your options. To create new folders, tap Tools then Manage Folders.
Chapter 6: Companion Programs Chapter 6 Companion Programs 106
Chapter 6: Companion Programs Companion programs include Microsoft® Pocket Word, Microsoft® Pocket Excel, Windows MediaTM Player for Pocket PC, and Microsoft® Reader. To switch to a companion program, tap , then Programs, then the program name. Pocket Word Pocket Word works with Microsoft® Word on your computer, providing easy access to copies of documents. You can also create new documents on your device or copy documents from your computer. , Programs, Pocket Word, then New.
Chapter 6: Companion Programs You can enter information in Pocket Word in one of four modes (typing, writing, drawing, and recording), which are displayed on the View menu. Each mode has its own toolbar, which you can show and hide by tapping the Show/Hide Toolbar button on the command bar. Note You can change the zoom magnification by tapping View then Zoom. Then select the percentage you want. Select a higher percentage to enter text and a lower one to see more of your document.
Chapter 6: Companion Programs Writing Mode In writing mode, use your stylus to write directly on the screen. Ruled lines are displayed as a guide, and the zoom magnification is greater than in typing mode to allow you to write more easily. For more information on writing and selecting writing, see “Entering Text Using the Input Panel” in Chapter 2. With Space button selected, drag to insert space. An arrow appears showing the space direction and size. Tap to highlight selected text.
Chapter 6: Companion Programs Drawing Mode In drawing mode, use your stylus to draw on the screen. Gridlines appear as a guide. When you lift your stylus off the screen after the first stroke, you’ll see a drawing box indicating the boundaries of the drawing. Every subsequent stroke within or touching the drawing box becomes part of the drawing. For more information on drawing and selecting drawings, see “Entering Text Using the Input Panel” in Chapter 2.
Chapter 6: Companion Programs Pocket Excel Pocket Excel works with Microsoft® Excel on your computer, providing easy access to copies of spreadsheets. You can also create new spreadsheets on your device or copy spreadsheets from your computer. , Programs, Pocket Excel, then New. Or, from the Today screen, tap To create a new file, tap New, then Excel Workbook. Only one spreadsheet can be opened at a time; when you open a second you will have to save the first.
Chapter 6: Companion Programs Tips for Working in Pocket Excel • To view in full screen mode, tap View then Full Screen. Tap Restore to exit mode. • Tap View to select items you want to show or hide. • To freeze panes, select the cell(s) you want to freeze, tap View then Freeze Panes. Freeze the top and leftmost panes in a spreadsheet to keep row and column labels visible as you scroll through a sheet. • To split panes to view different areas of a spreadsheet, tap View then Split.
Chapter 6: Companion Programs MSN® Messenger MSN® Messenger on your mobile device is an instant messaging program that lets you: • View a list of instant messaging contacts who are online. • Send and receive instant messages. • Have instant message conversations with groups of contacts. To use MSN® Messenger, you must have a Microsoft PassportTM account or a Microsoft® Exchange e-mail account. If you have a Hotmail® or MSN® account, you already have a Passport.
Chapter 6: Companion Programs Working with Contacts The MSN® Messenger window displays all your message contacts divided into Online and Not Online categories. While connected, tap and hold any contact and a pop-up menu appears allowing you to chat, send e-mail, block the contact or delete the contact. Tap a contact to start a chat. Tap and hold to display a pop-up menu of actions. Note To see others online without being seen, in the Tools menu, tap My Status and select Appear Offline.
Chapter 6: Companion Programs Chatting with Contacts Tap a contact name to open a chat window. Enter your message in the text entry area, or tap My Text to enter a preset message, and tap Send. To invite another contact to a multi-user chat, in the Tools menu, tap Invite and tap the contact you wish to invite. Enter message. Tap to send message. Note To switch back to the main window without closing a chat, tap the Contacts button.
Chapter 6: Companion Programs To see if the contact you are chatting with is responding, look for the message under the text entry area. View full chat. View status of the chat. For more information on using MSN® Messenger, tap 116 then Help.
Chapter 6: Companion Programs Windows MediaTM Player for Pocket PC Use Microsoft® Windows MediaTM Player for Pocket PC to play digital audio and video files that are stored on your device or on a network. To switch to Windows MediaTM Player for Pocket PC, tap , then tap Windows Media. Indicates the progress of the current track. Tap to adjust volume Tap to stop. Tap to play or pause. Tap to skip to the next file. Tap to play a previous file.
Chapter 6: Companion Programs Microsoft® Reader Microsoft® Reader enables you to read eBooks on your device. Using ActiveSync®, book files can be copied from your computer to your device. Each book consists of a cover page, an optional table of contents, and the pages of the book. You can: • Page through the book by using the cursor button on your device or by tapping the page number on each page. • Annotate the book with highlighting, bookmarks, notes, and drawings.
Chapter 6: Companion Programs Using the Library The Library is your Reader home page; it displays a list of all books stored on your device or storage card. To open the Library: • On the Reader command bar, tap Library. • On a book page, tap the book title, and then tap Library on the pop-up menu. To open a book, tap its title in the Library list. Tap to scroll through the Library list. Tap to select a sort order. Tap to open a book. Tap to specify the books you want to display in the list.
Chapter 6: Companion Programs Reading a Book Each book consists of a cover page, an optional table of contents, and the pages of the book. Navigation options are listed in the bottom portion of the cover page. The first time you open a book, you’ll probably want to go to the first page or to the table of contents, if there is one. Subsequently, whenever you open the book, you’ll be automatically taken to the last page read. In addition to the text, each book page includes a page number and book title.
Chapter 6: Companion Programs Using Reader Features Reading an eBook gives you several options not available with paper books. Select text by dragging stylus across it and follow options outlined below: • Search for Text: Find text by tapping Find on the pop-up menu. Enter your search word and tap the desired Find option. Results are highlighted on the page. Tap outside the box to close Find, and to return to your original page, tap the title then Return on the pop-up menu.
Chapter 7: Pocket Internet Explorer Chapter 7 Pocket Internet Explorer 122
Chapter 7: Pocket Internet Explorer Use Microsoft® Pocket Internet Explorer to view Web or WAP pages in either of these ways: • During synchronization with your computer, download your favorite links and mobile favorites that are stored in the Mobile Favorites subfolder in Internet Explorer on the computer. • Connect to an Internet service provider (ISP) or network and browse the Web. See “Accessing the Internet” in Chapter 3.
Chapter 7: Pocket Internet Explorer 5. If you want to download the pages that are linked to the mobile favorites you just created, rightclick the mobile favorite then click Properties. In the Download tab, specify the number of links deep you want to download. To conserve device memory, go only one level deep. 6. Synchronize your device and computer and the Mobile Favorites folder will be downloaded to your device.
Chapter 7: Pocket Internet Explorer Using AvantGo Channels AvantGo, a free interactive service that provides access to personalized content and popular websites, can be subscribed to directly from your device. Content can be downloaded when you synchronize your device and computer, or directly from the Internet. Visit the AvantGo website for more information. To sign up for AvantGo: 1. In ActiveSync® options on the computer, turn on synchronization for the AvantGo information type. 2.
Chapter 7: Pocket Internet Explorer Using Pocket Internet Explorer Pocket Internet Explorer can browse mobile favorites and channels that have been downloaded to your device without connecting to the Internet. Or, you can connect to the Internet through an ISP or a network connection. Hide pictures button. Favorites button. Home button. Refresh button.
Chapter 7: Pocket Internet Explorer Viewing mobile favorites: 1. Tap the Favorites button to display your list of favorites. Tap the favorite you want to view. Tap to add or delete a folder or favorite link. 2. Tap the page you want to view. The version of the page that was downloaded the last time you synchronized will be displayed. If the page is not on your device, the favorite will be dimmed.
Chapter 8: Getting Connected Chapter 8 Getting Connected 128
Chapter 8: Getting Connected Your device can exchange information with other mobile devices as well as your computer, a network, or the Internet. The connection options include the following: • The device’s infrared (IR) port can send and receive files from another device. See “Transferring Items Using Infrared” below for more information. • When connected to the Internet via your service provider, you can send and receive e-mail by using Inbox and view web and WAP pages using Pocket Internet Explorer.
Chapter 8: Getting Connected Connecting to the Internet You can connect to your ISP, and use the connection to send and receive e-mail messages and view Web or WAP pages. Note To connect to the Internet using Watcher, see “Accessing the Internet,” Chapter 3. Creating a modem connection to an ISP: 1. Obtain the following information from your ISP: ISP dial-up access telephone number, user name, password, and TCP/IP settings. Some ISPs require information in front of the user name, such as MSN/username. 2.
Chapter 8: Getting Connected Connecting to Work To connect to a network at work, you need to set up a RAS account through your network administrator, then follow the steps below in “Creating a modem connection to a network.” • Create a modem connection by using a RAS account. Before you can create this modem connection, your network administrator will need to set up a RAS account for you. If this is the method you want to use, see “Creating a modem connection to a network.
Chapter 8: Getting Connected Ending a Connection To disconnect, do one of the following: • When connected via dial-up or VPN, tap the Connection icon, tap End. , on your navigation bar and • When connected via cradle, detach your device from the cradle. • When connected via Infrared, move the device away from the other one.
Chapter 9: Optional Functions Chapter 9 Optional Functions 133
Chapter 9: Optional Functions Home To easily launch the built-in or installed applications, tap the icon displayed on the Home screen. Launching an Application from Home 1. Tap , Programs, then Home to display the Home screen. You can also launch the Home by pressing the device Home Program button. For initial setting, the respective application icons are registered on three tabs: Main, Programs and Games. In the Running tab, active applications are displayed. Tab. Tap to select Tab Settings or About.
Chapter 9: Optional Functions About Running The Running tab displays active applications. Icons do not appear. To activate/stop the application: To activate an application tap its name, or tap Activate in the pop-up menu. Tap to activate the selected application. Tap to stop the selected application, when finished, the application name disappears. Tap to stop all applications displayed in the Running tab. Tap View to select Text Color. Tap Tools for Tab Settings or About.
Chapter 9: Optional Functions Display Icon List The following list shows the tabs and icons for the initial setup.
Chapter 9: Optional Functions Moving an Application Icon into Another Tab A moved icon appears next to the last icon in its new location. It cannot be moved to a tab that already contains 18 icons. To move using pop-up menu: 1. Tap and hold the icon to be moved. 2. Tap Cut on the pop-up menu. 3. Tap the destination tab, then tap Paste on the Edit menu. Note You can also select Paste from the pop-up menu displayed by tapping and holding any portion other than the icon.
Chapter 9: Optional Functions Adding an Icon Application and file icons can be added to the Home screen. 1. Tap Edit, then Add to display the Add Application screen. You can also select Add from the pop-up menu displayed by tapping and holding any portion other than the icon. 2. Tap ▼ of Application file to show the file list. If there is no desired file on the file list, you can find it by tapping Browse. To refer to all folders and files, tap Browse to show the Browse Dialog screen.
Chapter 9: Optional Functions Tab Setting A tab can be added, deleted, or removed from the Tab Settings screen. Adding a tab: 1. Tap Tools, then Tab Settings. 2. Tap New to display a text box. 3. Enter the new tab name (up to 10 characters) and tap OK when finished. 4. Tap OK on the Tab Settings screen to return to the Home screen. Deleting a tab: 1. Tap Tools, then Tab Settings. 2. Select the tab to delete, then tap Delete. Tap Yes or No in the confirmation box.
Chapter 9: Optional Functions Text Color Setting To set the Text Color: 1. Tap the tab whose color you want to set to display the selected tab screen. 2. Tap View, then Text Color to display the color list. You can set the color of the application name as desired. 3. Tap the color you want to set, and the color of the application name changes.
Chapter 9: Optional Functions Backing Up Device data can be backed up on a storage card, which can be later restored to your device. Periodical data backup is strongly recommended. The following types of data can be backed up: • File: Files created by Pocket Word, Pocket Excel, Notes or other installed programs. Other files stored in the memory. • Registry: Setting information on Windows® CE or Built-in Program. • Database: Microsoft® Pocket Outlook® database information.
Chapter 9: Optional Functions 4. Tap OK to display the screen confirming all the applications are closed. 5. Tap OK to display the Backup password input screen. 6. Enter a password. Enter a password. You can enter a password up to 16 characters. Backup can be made even without entry of a password. If a password is entered, that password is required at the time of restore. Note If you choose a password, do not forget it. Backup data cannot be restored without entering it. 7. Tap OK.
Chapter 9: Optional Functions Carrying Out Restore Operation To restore is to overwrite the backed up data from the storage card onto the main memory of your device. • If the same file name exists in the main memory of your device, this file data is replaced with the backup data from the storage card. • If files exist in the main memory but not in the backup file, they will not be overwritten. 1. Insert the storage card, which contains backup data into your device. 2.
Chapter 9: Optional Functions Deleting a Backup File 1. Insert the storage card, which contains backup data to be deleted. 2. Tap , Programs, then Backup to display the Backup screen. 3. Select Delete Backup File from Functionality. 4. Tap OK to display the Delete Backup File confirmation screen. 5. Tap OK to delete the backup file.
Chapter 10 Additional Information
Chapter 10: Additional Information Resetting Reset is equal to “Restart” on a computer. Reset only in unusual circumstances such as when the screen freezes and doesn’t respond to tapping. Information not saved prior to resetting will be deleted. When your device is reset, phone functions are ended. To reset, press and release the Reset Switch while the power is on. Once reset, the Today screen appears.
Chapter 10: Additional Information Clearing Memory (Initialization) Initializing the device returns it to the status when it was originally purchased. Note Initializing the device deletes all stored data, except built-in programs. Before initialization, we recommend storing the memory data of the device into your computer or a storage card. Before initialization, remove a storage card. To initialize: 1. Turn off the power. 2.
Chapter 10: Additional Information Specifications External dimensions Operating conditions Built-in battery Processor Memory Display Interface SD card slot 3 in. x 5 in. x 3/4 in. (excluding protrusion part) (77.5(W) x 127.5(H) x 19.5(D) mm) Temperature: 32°F to 104°F (0°C to 40°C), Humidity: 30 to 80% RH • Temperature capable of charging: 41°F to 95°F (5°C to 35°C) (According to the operating status, the charging may pause even when the ambient temperature is below 95°F (35°C).
FDA Consumer Update U.S. Food and Drug Administration - Center for Devices and Radiological Health Consumer Update on Wireless Phones 1. Do wireless phones pose a health hazard? The available scientific evidence does not show that any health problems are associated with using wireless phones. There is no proof, however, that wireless phones are absolutely safe. Wireless phones emit low levels of radiofrequency energy (RF) in the microwave range while being used.
FDA Consumer Update FDA shares regulatory responsibilities for wireless phones with the Federal Communications Commission (FCC). All phones that are sold in the United States must comply with FCC safety guidelines that limit RF exposure. FCC relies on FDA and other health agencies for safety questions about wireless phones. FCC also regulates the base stations that the wireless phone networks rely upon.
FDA Consumer Update 5. What research is needed to decide whether RF exposure from wireless phones poses a health risk? A combination of laboratory studies and epidemiological studies of people actually using wireless phones would provide some of the data that are needed. Lifetime animal exposure studies could be completed in a few years. However, very large numbers of animals would be needed to provide reliable proof of a cancer promoting effect if one exists.
FDA Consumer Update Manufacturers of wireless phones must report the RF exposure level for each model of phone to the FCC. The FCC website (http://www.fcc.gov/oet/rfsafety) gives directions for locating the FCC identification number on your phone so you can find your phone’s RF exposure level in the online listing. 8.
FDA Consumer Update Some groups sponsored by other national governments have advised that children be discouraged from using wireless phones at all. For example, the government in the United Kingdom distributed leaflets containing such a recommendation in December 2000. They noted that no evidence exists that using a wireless phone causes brain tumors or other ill effects.
AUDIOVOX COMMUNICATIONS CORP. 555 Wireless Blvd., Hauppauge, New York 11788, 800-229-1235 16808 Marquardt Avenue, Cerritos, California 90701, 562-802-5100 http://www.audiovox.