Operating Instructions Dishwasher G 5220 G 5225 To prevent accidents and appliance damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS . . . . . . . 4 Guide to the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Interrupting a program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Changing a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Additional options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Turbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Delay start . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS WARNING – When using your dishwasher, follow basic precautions, including the following: Read the operating instructions and installation diagram carefully before installation or use of the dishwasher to prevent injury and machine damage. Use the dishwasher only for its intended purpose. This appliance is intended for residential use only. Keep these operating instructions in a safe place and pass them on to any future user.
IMPORTANT SAFETY INSTRUCTIONS Installation ~ The dishwasher must be installed and connected in accordance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ Do not install or use a damaged dishwasher. A damaged appliance is dangerous. Unplug the machine and contact Miele Technical Service Department. ~ Ensure that any plastic wrappings, bags, etc.
IMPORTANT SAFETY INSTRUCTIONS Use ~ To reduce the risk of injury, do not allow children to play in, on or near the dishwasher. It is possible for small fingers may be pinched in the door. ~ Only use the dishwasher if all panels are properly in place. ~ Do not tamper with the controls. ~ Do not sit or stand on the door or baskets of the dishwasher. Close the door when not in use. ~ Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more.
Guide to the dishwasher a Upper spray arm (not visible) g Triple filter system b Cutlery tray h Data plate c Upper basket i Child Safety Lock in the door handle (not visible) d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm j Rinse aid reservoir k Dual compartment detergent dispenser l Salt container 7
Guide to the dishwasher Control panel a Program selection f Delay start button with indicator light b Time display g Turbo button with indicator light c Program sequence indicator h Program button d Check / Refill indicators i K button (On/Off) e Start/Stop button with indicator light This operating instruction manual describes several dishwasher models with different indicated settings. The different dishwasher models are named : Standard = Dishwasher with 31 11/16" (80.
Caring for the environment Energy saving washing This dishwasher is economical in the use of water and electricity. For best results follow these tips: ^ For lowest energy consumption you may connect the dishwasher to a cold water source. ^ For fastest possible wash times, with slightly higher energy consumption, connect the dishwasher to a hot water source. ^ Make full use of the baskets without overloading for the most economical washing. ^ Use the correct amount of detergent and rinse aid.
Before using for the first time To open the door Child safety lock ^ Reach under the handle and pull the door open. Te child Safety Lock is designed to prevent children from opening the dishwasher. If the door is opened during operation the dishwasher will stop running. Once the door is closed the program will restart. To close the door ^ Push the baskets in. ^ Lift the door and push until it clicks into place. 10 ^ To lock the door, push the slider below the door grip to the right.
Before using for the first time Water softener To achieve good cleaning results, the dishwasher needs soft water (water that is low in minerals). Hard water results in calcium deposits on dishware and in the dishwasher. If your tap water hardness is above 4 °d (4 gr/gal) the water should be softened. The built-in water softener is designed for this purpose. The water softener is suitable for a water hardness up to 70 °d (73 gr/gal).
Before using for the first time Programming the water softener To exit the programming mode at any time turn the dishwasher off with the K button. ^ Press the K button to turn the dishwasher off. ^ Press and hold the "Start / Stop" button and turn the dishwasher on simultaneously using the K button. Keep the "Start / Stop" button pressed for at least four seconds until the "Start / Stop" indicator light comes on. If it does not come on, start over. ^ Now press the "Delay Start" button twice.
Before using for the first time Checking the programmed water hardness ^ Press the K button to turn the dishwasher off. ^ Press and hold the "Start/Stop" button and turn the dishwasher on simultaneously using the K button. Keep the "Start/Stop" button pressed for at least four seconds until the "Start/Stop" indicator light comes on. ^ Press the "Delay Start"" button twice. The Delay Start indicator will flash twice briefly in intervals. Character will flash in sequence in the display.
Before using for the first time Every dishwasher is tested before leaving the factory. Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used. Important: The salt container must be filled with 2 quarts (2 l) of water before adding salt for the first time so the salt can dissolve properly. Water does not have to be added with subsequent refills.
Before using for the first time Refill salt message ^ When the "Salt" indicator light comes on, refill the salt after the program has finished. After the container has been filled, the "Salt" indicator light can remain on for a short time. It will go out once the reactivation process is complete. The "Salt" indicator light is turned off if you have programmed the dishwasher to a water hardness below 4 °d (4 gr/gal).
Before using for the first time Deactivate indicators If you only ever use "Tab" detergent products in your dishwasher, you can switch both messages off if you wish. ^ Turn the dishwasher off with the K button. ^ Press and hold the "Start/Stop" button and turn the dishwasher on simultaneously using the K button. Keep the "Start/Stop" button pressed for at least four seconds until the "Start/Stop" indicator light comes on. If it does not come on, start over. ^ Press the "Delay start" button nine times.
Before using for the first time Rinse aid Rinse aid is needed to prevent spotting on dishes and glassware. The rinse aid is filled in the reservoir and the set amount will be automatically dosed. ,Filling the rinse aid reservoir with detergent will damage the reservoir. Only pour rinse aid formulated for residential dishwashers into the reservoir. When using "Tab" detergents rinse aid is not needed.
Before using for the first time Rinse aid indicator When the Rinse aid indicator first comes on, there will be enough rinse aid left for 2 - 3 washes. ^ The rinse aid indicator on the control panel will light when the rinse aid reservoir needs refilling. If you only ever use "Tab" detergent products in your dishwasher, you can switch the reminders for salt and rinse aid off if you wish (see "Before using for the first time - Refill salt message").
Before using for the first time Adjusting the dosage In order to obtain an optimal cleaning result you can adjust the dosing quantity of the rinse aid. The dosage selector is preset to 3. This dispenses approximately 3 ml of rinse aid per program. It can be adjusted from 0 to 6. – Use a higher setting if spots appear on dry glassware. ^ Use a lower setting if streaking appears on dishes or glasses. P 3 will flash in the display. This means that the rinse aid dosage has been set to 3 ml at the factory.
Loading the dishwasher ,Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher. Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher. Wax, grease and paint will cause permanent discoloration and damage to the dishwasher. ^ Scrape food from dishes before placing them in the dishwasher, rinsing is not necessary. ^ Some foods contain natural dyes, e.g. carrots or tomatoes.
Loading the dishwasher Items not recommended for dishwashing – Cutlery with wooden handles – Wooden cutting boards – Glued items such as old knives with handles glued together around the shank of the blade – Handmade craft items, antique, metal trimmed or decorative glassware Glassware: – There are no standard guidelines for washing glassware, when in doubt wash by hand. – When purchasing new dishes, glasses and cutlery, make sure they are dishwasher safe.
Loading the dishwasher Typical load for 10 place settings with cutlery tray Upper basket Cutlery tray 22 Lower basket
Loading the dishwasher Typical load for 16 place settings with cutlery tray Upper basket Lower basket Cutlery tray 23
Loading the dishwasher Typical load for 10 place settings with cutlery basket Upper basket Cutlery basket 24 Lower basket
Loading the dishwasher Typical load for 13 place settings with cutlery basket Upper basket Lower basket Cutlery basket 25
Loading the dishwasher Upper basket ,Always use the dishwasher with the upper and lower basket in place. Adjustable cup rack (depending on model) ^ Raise the rack to make room for tall glasses. Glasses can also be leaned against the cup rack so they are more stable. ^ Lower it to double stack smaller pieces. ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls and flat pans.
Loading the dishwasher Adjusting the upper basket To adjust the upper basket downwards: In order to gain more space for taller items the upper basket can be adjusted on three levels with 2 cm between each level. ^ Pull up on the levers at the sides of the upper basket. The upper basket can also be set at an angle with one side high and the other side low. Make sure, however, that the basket can slide smoothly in and out of the cabinet. ^ Slide out the upper basket.
Loading the dishwasher Lower basket Heavily soiled items ^ Place larger and heavier items such as plates, serving platters, saucepans, bowls, etc. in the lower basket. It can also be used for glasses, cups, small plates and saucers. Dishwasher with cutlery tray ^ Place very large plates in the center of the lower basket. Dishwasher with cutlery basket When tilted, plates up to 13 3/4" (35 cm) in diameter can be accommodated.
Loading the dishwasher MultiComfort zone The rear section of the lower basket is used for cups, glasses, plates, pots and pans. ^ The glass rack can be folded up to make more room for tall items. ^ Stemware, e.g. wine, champagne and beer glasses, can be leaned against the glass rack or suspended from it. Foldable spikes (depending on the model) The spikes at the front are used for plates, soup bowls, platters, desert bowls, and saucers.
Loading the dishwasher Cutlery tray (depending on model) ^ Arrange the cutlery as shown in the cutlery tray. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc. Place knives with the cutting edge down and forks with the prongs between the holders. Spoons should be placed in the opposite direction with the handles between the holders so that water can run off more easily. The upper spray arm must not be blocked by tall cutlery items.
Loading the dishwasher Cutlery basket Cutlery insert for the cutlery basket (depending on model) Use the insert supplied for heavily soiled items of cutlery. The insert separates the items so that they can be reached better by the spray jets. The cutlery basket can be placed anywhere on the front rows of spikes in the lower basket. ^ To avoid risk of injury, knives and forks should be placed with the handles upwards in the basket.
Optional accessories Optional dishwasher accessories are available from your Miele dealer, Miele or Mieleusa.com (depending on your model some may already be supplied with your machine as standard). If you would like to... the following accessory will need to be ordered... ...wash a Miele Cappuccinatore ... a Cappuccinatore insert for the upper basket. ...wash additional items of cutlery ... a cutlery basket for the lower basket. ...wash long-stemmed glassware ...
Use Detergent ,Dishwasher detergents contain irritant and corrosive ingredients. Avoid inhaling or swallowing dishwasher detergent. Keep children away from detergent. Keep detergent out of the reach of children. Keep children away from the dishwasher when the door is open. There could still be detergent residues in the dishwasher. Only add detergent just before starting the program and lock the door with the child safety lock (depending on model). You can use powder, gel or tab detergents.
Use Adding detergent ^ Press the latch on the detergent dispenser. The flap will spring open. The flap is always open at the end of a program. ^ Add detergent to the compartments and close the container flap. ^ Use one tab or add powder or gel detergent to compartment II and close the flap. ^ If a Pre-rinse is desired, and available for your chosen program, add 1 teaspoon (5 ml) of detergent to compartment I. Compartment I holds a maximum of 2 teaspoons (10 ml), compartment II holds a maximum of 3.
Use Turning the dishwasher on Starting a program ^ Make sure the spray arms can rotate freely. ^ Press the Start/Stop button. ^ Close the door. ^ Open the water supply if it is closed. ^ Press the K button to turn the dishwasher on. The Start/Stop indicator flashes, and the indicator for the last selected program comes on. Selecting a program The program starts. The Start/Stop and Rinse indicators and the indicator for the selected program come on.
Use Program guide When to use Program sequence Pre-rinse 1 Main wash 2 X 1 X X X X X X X X X X X as Program for completely required washing a full load of normally soiled dishware with the ability to adjust energy and water consumption based on the soil load of the dishware. China & Crystal For temperature sensitive glassware and lightly soiled dishware, use 50% detergent recommended. SaniWash To sanitize dishware, e.g. baby bottles, cutting boards and preparation dishware.
Use Time display Standby Before the program starts, the time display shows the time of the selected program in hours and minutes. The remaining time is displayed during the program. A few minutes after the last button is pressed or a few minutes after the end of the program the dishwasher will switch to Standby mode to save energy. The time display and the indicator lights are turned off and only the Start/Stop indicator light flashes slowly. The time that is displayed may vary for the same program.
Use Program sequence indicator After a program has started, the program sequence indicator displays the respective program step. At the end of a program The program has ended when a 0 appears in the time display and "End" lights up in the program sequence display. If the Express program was selected, the drying fan will run for a few minutes after the program has ended. ^ Open the door. ^ Press the K button to turn the dishwasher off.
Use Interrupting a program A program will be interrupted as soon as the door is opened. When the door is closed again, the program will continue from where it was interrupted. ,Water in the dishwasher is hot. Risk of scalding! Only open the door if absolutely necessary and be very careful. Before closing the door again, leave it slightly ajar for approx. 20 seconds. This will allow the temperature in the wash cabinet to settle. Then push the door firmly shut until it clicks into place.
Additional options Turbo The "Turbo" function can be used to reduce the program run-times, in programs in which the option is available. Energy consumption will increase to achieve optimum results. ^ Press the K button to turn the dishwasher on. The Start/Stop indicator light flashes. ^ Select the desired program. ^ Press the Turbo button. The Turbo indicator light comes on. ^ Now you can start a program. Once selected, the function will remain active for all programs until the setting is changed.
Additional options Delay start The start time of a program can be delayed. The start time can be delayed from 30 minutes to 24 hours. The delay is set in 30 minute increments. For a delay start time between 30 minutes and 9 hours 30 minutes, the delay is set in 30 minute increments. For a delay start time of 10 hours or more, the delay is set in increments of one hour. When using the Delay start function, make sure that the detergent compartment is dry before adding detergent. Wipe dry if necessary.
Additional options The time will count down to the program start: for more than 10 hours in 1 hour increments, for less than 10 hours in 1 minute increments. When the set time is reached, the selected program will start automatically. The remaining time is shown in the time display, the Delay start indicator light goes out and the Start/Stop indicator light comes on. Delay start time shown in the time display: up to 59 minutes: e.g. 30 minutes = 30 1 hour to 9 hours 30 minutes: e.g. 5 hours = 5.
Additional options Optimize Standby A few minutes after the last button is pressed or a few minutes after the end of the program the dishwasher will switch to Standby mode to save energy. The time display and the indicator lights are turned off and only the Start/Stop indicator light flashes slowly. If the dishwasher is not turned off or opened after the program ends, after a few minutes in Standby mode it will turn off completely. You can also deactivate the Optimize Standby function.
Additional options Factory defaults If you have changed any settings, you can reset them to the factory defaults. ^ Press the K button to turn the dishwasher off. ^ Press and hold the Start/Stop button and simultaneously turn the dishwasher on using the K button. Keep the Start/Stop button pressed for at least four seconds until the "Start/Stop" indicator light comes on. If it does not come on, start over. ^ Press the Delay start button 12 times.
Frequently asked questions ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem After turning on the dishwasher with the K button, the Start/Stop indicator light does not flash. Possible fault The dishwasher is not plugged in. The circuit breaker has tripped. Solution Insert the plug. Reset the circuit breaker.
Frequently asked questions Faults in the water intake or water drain Problem The Intake/Drain indicator light alternates between flashing and remaining steady. Possible fault Solution The water supply is closed. Open the water supply all the way. The dishwasher stops running. The Intake/Drain indicator light flashes. The time display shows fault FXX. Before fixing the fault: – Press the K button to turn the dishwasher off. Fault F12/F13: – Open the water supply all the Water intake fault. way.
Frequently asked questions General problems with the dishwasher Problem The time display is dark. Only the Start/Stop indicator light flashes slowly. There are detergent residues in the dispenser at the end of a program. The detergent dispenser flap cannot be closed properly. The inside of the door and/or the interior walls are wet after a program has finished. There is water in the wash cabinet at the end of a program.
Frequently asked questions Sounds Problem There is a knocking noise in the wash cabinet There is a rattling noise in the wash cabinet There is a knocking noise in the water line 48 Possible fault Solution The spray arm is hitting an Interrupt the program, item in the basket. rearrange items blocking the spray arms. Items are not secure in the Interrupt the program, and wash cabinet. rearrange loose pieces.
Frequently asked questions Poor cleaning results Problem The dishes are not clean. Possible fault The dishes were not loaded correctly. The program was not powerful enough. Solution See "Loading the dishwasher". Select a more intensive program (see "Program Guide"). Not enough detergent was Use more detergent, or dispensed. change the detergent. The spray arms are blocked. Turn the spray arms and rearrange the dishes if necessary. The triple filter in the wash Clean the filter and insert it correctly.
Frequently asked questions Problem Possible fault Dishes are not dry, The rinse aid setting may be glasses and too low, or the rinse aid cutlery are reservoir is empty. spotted. Dishes were taken out too soon. A "Tab" product was used. These products have a low drying effect. Not enough rinse aid was White residue is visible on cutlery used. and dishes. Clouding occurs The salt container is empty. on glassware and cutlery; film can be The salt container lid was not wiped off. correctly screwed on.
Frequently asked questions Problem Possible fault Solution Glasses have a brown or blue discoloration; film cannot be wiped off. Glasses are dull and discolored; film cannot be wiped off. Detergent deposits. Change detergent right away. Glasses are not dishwasher safe. The surface is affected. Tea or lipstick stains The wash temperature of have not been the selected program was completely removed. too low. The detergent has a low bleaching effect. Plastics are Natural dyes e.g. from discolored.
After sales service Repairs MieleCare In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. (USA only) ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door. PC Update The Program Correction (PC) allows a technician to update the dishwasher to make use of new technology.
User Maintenance Instructions To prevent accidents and machine damage, read these instructions before installation or use.
Cleaning and Care Exterior Check and clean your dishwasher regularly. This will help avoid problems and faults. ,Abrasive cleaning agents, all-purpose cleaners, thinner or ammonia based cleaners should not be used on the dishwasher. They will damage the surface. Wash cabinet Generally, the wash cabinet is self cleaning if the correct amount of detergent is used. ^ Only use a conditioner suitable for your kitchen cabinetry. ^ Clean wood only with a damp cloth and wipe dry.
Cleaning and Care Triple filter system The triple filter system in the base of the wash cabinet prevents food from being redeposited on dishes. It also protects the circulation pump from damage caused by foreign objects (e.g. broken glass, bones). During normal use, the filter system is self-cleaning. ,The machine must not be used without all the filters in place! ^ Check and clean the filter system periodically for any trapped or foreign objects.
Cleaning and Care To clean the inside of the filter, the flap must be opened. ^ Return the filter so it lies flat in the base of the wash cabinet. ^ Push the clips together a and open the flap b. ^ Lock the filter by turning the handle clockwise. ^ Rinse under running water. ^ Close the flap so that the clip engages. 56 ,The triple filter system must be inserted and locked into place. Large particles could get in the circulation system and cause a blockage.
Cleaning and Care Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray arms should be inspected and cleaned every 4 - 6 months. ^ Turn off the dishwasher before cleaning. Removing the spray arms ^ Remove the cutlery tray (if present). ^ Push the upper spray arm up to engage the inner ratchet and unscrew the spray arm. ^ Lift up the middle spray arm, a, to engage the ratchet and unscrew the spray arm, b. ^ Remove the lower basket.
Cleaning and Care Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ Turn off the dishwasher and pull the plug. ^ Remove the triple filter (see "Triple filter system"). ^ Use a cup or bowl to scoop water out of the wash cabinet. The drain pump is beneath the non-return valve (see arrow). ^ Remove all foreign objects from the drain pump (glass or bone splinters).
Installation Instructions Please refer to the Installation Diagram supplied with these instructions. Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information.
Electrical connection ,Installation, repairs and other work by unqualified persons could be dangerous. Check that the voltage, frequency and fuse rating shown on the data plate match the household mains supply. The power outlet must be accessible after installation. Do not use an extension cord to connect the dishwasher to the mains. Danger of overheating! See data plate on the right side of the door. A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician.
Electrical connection Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. ,CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards.
Plumbing Connection to the water supply ,Installation, repairs and other work by unqualified persons could be dangerous. ,Do not drink water from the dishwasher! – The dishwasher can heat its own water to the temperature required by the wash program. This allows for connection of the machine to either a hot (max. 140°F / 60°C) or cold water source. For lowest energy consumption and fastest possible wash times connect the dishwasher to a hot water source. All programs use hot water in the rinse cycles.
Plumbing Drainage – The machine comes equipped with a built-in non-return valve on the discharge side to prevent waste water from flowing back into the dishwasher. – The dishwasher is equipped with a 5 ft (1.5 m) flexible drain hose with an internal diameter of 7/8" (22 mm). – Drain hose extensions and adapters can be ordered from Miele. The maximum drain hose length is 13 ft. (4 m), max. drain height: 39" (1 m).
Noise measurement General requirements for measuring noise The dishwasher must be loaded with 16 place settings and the Normal program must be used. Installation requirements for measuring noise The dishwasher must be installed as follows:. ^ Install the dishwasher into an appropriate housing unit. ^ Secure the front panel.
Noise measurement ^ Push the insulation mat supplied (depending on model) under the plinth until it is up against the appliance feet a. ^ Attach the toe-kick so that it is flush with the door front b.
Alteration rights reserved / 0313 G5220/G5225 / M.-Nr. 09 510 211 / 01 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
