VME9020TS MULTIMEDIA RECEIVER MANUAL/WARRANTY CARD
CONTENT - Preparation p. 3 - Adjustment of the Touch Screen Monitor p. 5 - Installation p. 6 - Controls and Indicators p. 10 - Front Zone Remote Control p. 13 - Multi-ZONE Remote Control p. 18 - Using the TFT Monitor p. 20 - Operating Instructions p. 23 - System Setup Menu p. 27 - Tuner Operation p. 35 - RDS Information p. 37 - DVD Player Operation p. 40 - DVD Setup Menu p. 50 - CD/MP3/WMA Operation p. 58 - SD Card Reader Operation p. 61 - iPod Operation p.
PREPARATION Congratulations on your purchase of the Audiovox VME9020TS Mobile Multimedia AM/FM/DVD/TV Tuner/SD Card/iPod (ready) Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Audiovox VME9020TS installed by a reputable installation shop. Features • ISO Double-DIN chassis • Light weight proprietary DVD core mechanism • Wide screen (16:9) 6.
• Over and under voltage protection to insure the unit operates within designed parameters • Damped DVD mechanism with 16 Mbit flash memory ESP (Electronic Shock Protection) provide smooth disc playback under the severest road conditions Tools and Supplies You will need these tools and supplies to install your VME9020TS: • Torx type, flat-head and Philips screwdrivers • Wire cutters and strippers • Tools to remove existing radio (screwdriver, socket wrench set or other tools) • Electrical tape • Crimping to
Battery disposal: At the end of the product´s useful life, please dispose of it at appropriate collection points provided in your country. Disconnecting the Battery To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation. NOTE: If the VME9020TS is to be installed in a car equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost.
INSTALLATION This unit is designed to fit into a 2.0 DIN dashboard opening, found in many imported cars. The unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai, Honda... vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of installation. 1.
3. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with wire nuts or electrical tape. After completing the wiring connections, plug the ISO connectors into the mating sockets on the rear of the chassis. Turn the unit on to confirm operation (vehicle ignition switch must be “on”).
Using the Cosmetic Trim Ring A trim ring is packaged with the VME9020TS for installation flexibility. The VME9020TS will fit into most import dashes with little or no modification to the dash board/cavity. Some European and US domestic vehicle dashes will accept a DoubleDIN chassis, but there is usually a small gap between the radio and dash piece after installation is complete. In this case, use the trim ring to conceal any gaps that may be present.
WIRING iPod SUBJECT TO TECHNICAL CHANGE 9
CONTROLS AND INDICATORS 1. POWER/MUTE Press the POWER/MUTE button (1) once to turn the unit on. Press again to mute the volume. Press and hold to turn the unit off. 2. AUDIO/LOC Press the AUDIO/LOC button (2) to access the audio menu and change and/or confirm audio settings. Press and hold to activate or deactivate the LOCAL (LOC) setting. 3. VOL + Press to increase the volume. 4. VOL Press to decrease the volume. 5.
9. Joystick/ • DVD Mode: Press once to enter the next chapter or track. • TUNER Mode: Press once to auto-search the next available radio station. Press and hold to decrease the tuner frequency step-by-step. • MENU Mode: Press once to move the cursor to the right. • TV Mode: Press to go up one frequency step. 10. TUNER Press to access the radio tuner source and then to change between AM and FM bands. 11. MENU/SRC Press to access the playing source menu. 12.
21. Disc Slot 22. Eject Button • Press once to eject the disc. • Press and hold to reset the mechanism. 23. Disc Indicator 24. SD Card Slot 25.
FRONT ZONE REMOTE CONTROL FUNCTIONS Button Name/Ref # MENU 1: DVD: Enters the main menu of the disc VCD: Turns on PBC when playing VCD TITLE 2: DVD: Enters the title menu of the disc VCD: Plays first ten seconds of each chapter/title MUTE 3 Toogles on/off audio output POWER 4: DVD/VCD/Tuner/CD/MP3: Turns the power on. Press and hold to turn the power off.
ANGLE 11: DVD/VCD/TUNER/CD/MP3: Continuously adjusts front panel tilt angle ANGLE 12: DVD/VCD/TUNER/CD/MP3: Continuously adjusts front panel tilt angle ANGLE 13: DVD: Plays back disc in different angle for a scene VCD: Plays back Picture CD with different angle of picture displayed 14: DVD/VCD/TUNER/CD/MP3: Fast forwards the disc content VOL- 15: DVD/VCD/TUNER/CD/MP3: Decreases volume VOL+ 16: DVD/VCD/TUNER/CD/MP3: Increases volume 17: DVD: Selects the previous chapter for playback VCD: Selects the
/BAND 20: DVD: Stops playback VCD: Stops playback TUNER: Selects FM/AM band CD/MP3: Stops playback GOTO 21: DVD/VCD: Goes to specific time frame and playback II 22: DVD/VCD: Slow playback/slow rewind playback ZOOM 23: DVD/VCD: Zooms in/out on an image PIC 24: DVD/VCD: Displays set-up parameters OPEN/CLOSE 25: DVD/VCD/TUNER/CD/MP3: Opens/Closes the TFT monitor v 26: v DVD/VCD/TUNER/CD/MP3: Decreases monitor tilt angle ^ ^ 27: DVD/VCD/TUNER/CD/MP3: Increases monitor tilt angle WIDE 28: DVD/VCD/TUNER/CD/M
DVD SETUP 30: DVD/VCD/TUNER/CD/MP3: Access DVD Setup menu SYS SETUP 31: DVD/VCD/TUNER/CD/MP3: Access System Setup menu SEL 32: Audio adjustment (EQ, Bass, Treble, Fader, Bal, Sur, Loud) RDM 33: DVD: Plays all chapters in random order CD/MP3: Plays all tracks in random order SCN 34: CD/MP 3: Plays the first ten seconds of each track EJECT 35: DVD/VCD/TUNER/CD/MP3: Ejects disc 16
Note: Your remote control may differ slightly from the one pictured here. The above diagram is for illustrative purposes only.
MULTI-ZONE REMOTE CONTROL FUNCTIONS Button Name/Ref # MENU 1: DVD: Enters the main menu of the disc VCD: Turns on PBC when playing VCD TITLE 2: DVD: Enters the title menu of the disc VCD: Plays first ten seconds of each chapter/title MUTE 3: DVD/VCD: Toggles on/off audio output AUDIO 5: DVD: Switches the audio language for disc playback REPT 7: DVD/VCD: Setup to repeat playback of each chapter/title/disc R.
19: DVD/VCD: Selects the next track/chapter for playback GOTO 21: DVD/VCD: Goes to specific time frame and playback II 22: DVD/VCD: Slow playback/slow rewind playback 0-9 (Numeric Keypad) 29: DVD: Directly accesses chapter Note: Your remote control may differ slightly from the one pictured here. The above diagram is for illustrative purposes only.
USING THE TFT MONITOR Open/Close TFT Monitor Press the OPEN button (12) on the front panel or press the ( ) button (25) of the front zone remote control to open/close the monitor. TFT Monitor Auto Open • If “TFT Auto Open” is “on” when the unit is turned on, the monitor automatically moves to the last viewing position. • If “TFT Auto Open” is ”off” when the unit is turned on, press the OPEN button (12) or ( ) button (25) on the front zone remote control to move the monitor into the desired viewing position.
FULL The entire screen is extended horizontally to the aspect ratio of 16 to 9. The extension ratio is the same at any point. WIDE The screen is extended horizontally to the aspect ratio of 16 to 9. The extension ratio increases toward the right and left ends of the screen. NORMAL The conventional display image has a 4 to 3 ratio of horizontal to vertical, leaving a blank area on the right and left sides of the display.
Adjustable Parameters While in DVD or TUNER mode, the only parameter that can be adjusted is brightness (BRIGHT). To access “PICTURE”, “COLOR”, ”CONTRAST”, and “TINT” you must be in AUX or CAMERA mode. NOTE: The default adjustment is “0” in PAL mode. Tint is unavailable for adjustment. Parameter Adjustment Procedure 1. Enter Picture Quality Setting mode: Press the PIC button (24) on the remote or press and hold the DISP/PIC button (13) on the unit. 2.
OPERATING INSTRUCTIONS Power On / Off Press the MUTE button (1) to turn the unit on. The buttons on the front of the unit light up. Press and hold the MUTE button (1) on the front panel or the POWER button (4) on the remote to power off the unit. Audible Beep Confirmation An audible beep tone confirms each function selection. The beep tone cannot be disabled. Mute Press the MUTE button (1) on the front panel or the MUTE button (3) on the remote to mute the volume from the unit.
Volume Adjustment To increase or decrease the volume level, turn the ROTARY ENCODER (6) on the front panel or press the VOL+/VOL- buttons (15, 16) on remote control. When the volume level reaches “0” or “40”, a beep sounds, indicating that the adjustment limit has been reached. The volume ranges from “0” to 40”. The LCD or TFT screen displays the volume level for 3 seconds.
Table 4: Audio Adjustments Audio Function Adjustable Range EQ User Flat Jazz Pop Classical Bass Treble Rock Vocal -14 to +14 -14 to +14 Fade -9 to +9 Bal SW Loud -9 to +9 - 7 to +7 Off, 1-4 Note: The Bass and Treble levels are only adjustable when EQ is set to “User” mode. The Loud function compensates for deficiencies in sound ranges at low levels. Loudness levels range from 1-4 or “off”. When the Loud function is on, LOUD is displayed on the screen.
Six-Channel Audio Control Note: Before adjusting the volume of any speaker, please refer to “Surround Setup” on page 55.
SYSTEM SETUP MENU In “System Setup” mode, “ASP CONFIG”, “RDS SETUP” and “GENERAL SETUP” are available for adjustment. Setup can be performed by pressing the dedicated button on the remote control or by pressing the MENU/SRC button (11) on the front panel. For system settings, press the SYS SETUP button (31) on the remote control or touch “SETUP” on the screen to enter the “SETUP” menu. “SYS SETUP” is highlighted in green.
Selecting a Feature for Adjustment Press the or II buttons (14, 22) on the remote control or the or buttons (6, 7) on the joystick to select the feature to be adjusted. Adjusting a Feature 1. Enter the option field for the feature you want to adjust by pressing the / II button (18) on the remote or by pressing the ENTER (joystick) button (5) on the unit. A submenu appears in a second row with the selected option highlighted in light blue. 2.
Table 6: General Setup Menu Features Setting Options Function Radio USA1 Select the appropriate setting based on the country in which you reside. S. Amer 1 Arabia China S. Amer 2 Europe Korea Clock Mode Screen Saver 12H Clock displays 12 hour time using AM and PM. 24H Clock displays 24 hour time up to 23:59. On Turn screen saver on/off. Off TV System Auto NTSC TFT Auto Open The color signal output is switched automatically based on the current disc.
Adjusting the Clock 1. Access the “Clock” setting under the General Setup menu. 2. Press the or II buttons (14, 22) on the remote control or the or buttons (6, 7) on the joystick to move the cursor to the “Hour” or “Min” position. 3. Press the or buttons (17, 19) on the remote control or the or buttons (8, 9) on the joystick to adjust the hour or minutes. 4. Press the II button (14) on the remote control to confirm setup.
Adjusting a Feature 1. Enter the option field for the feature you want to adjust by pressing the /II button (18) on the remote or by pressing the ENTER (joystick) button (5) on the unit. A submenu appears in a second row with the selected option highlighted in light blue. 2. Select a new value by pressing the or II buttons (14, 22) on the remote control or the or buttons (6, 7) on the joystick. 3.
Table 7: ASP Config Menu Features Setting Options Function Bass Center Freq 60Hz 80 Hz According to the audio source, select the Bass Center Frequency to achieve the best Bass effect. 100Hz 130Hz 150Hz 200Hz According to the audio source, select the Bass Center Treble Center 10KHz Freq 12.5KHz Frequency to achieve the best Treble effect. 15KHz 17KHz Sub.W Filter 80Hz 120Hz 160Hz Sub.
MULTI-ZONE OPERATION Independent sources can be played simultaneously on the VME9020TS. For example, a video game console can be seen on the front screen while DVD video is available to rear passengers. NOTE: If DVD is selected as the front source and SD Card is selected for the rear source, then both sources will switch to SD Card. If SD Card is selected as the front source and DVD is selected for the rear source, then both sources will switch to the DVD source.
Selecting a Source for the Rear Zone To access the rear zone SOURCE MENU, touch the top right corner of the screen, near the Multi-ZONE icon. Select the source to be directed to the rear Multi-ZONE RCA outputs. NOTE: Optical media and an SD Card cannot be selected from the Multi-ZONE Source Menu simultaneously. NOTE: The AM/FM tuner graphics will change to a "blue screen" background when any optical or SD Card media is selected from the MultiZONE menu.
TUNER OPERATION Tuner TFT Display 1. Current Radio Band Indicator 2. Radio Frequency Indicator 3. Clock 4. Stereo Broadcasting Indicator 5. Strong Local Signal Broadcasting Indicator: Touch and hold to activate/deactivate Local function 6. Preset Radio Stations: Touch to recall preset stations or touch and hold to store a station 7. Front Zone Playing Mode 8. Rear Zone Playing Mode 9. User Defined Equalizer Level 10. Loud Setting Indicator 11. Current Preset Station Indicator 12.
Switch to Radio Tuner source Press the TUNER button (10) on the front panel or the SRC button on the remote control (8) to switch to the TUNER source. Select FM/AM Band Touch the BAND button (16) on the screen, or press the TUNER button (10) on the unit or the BAND button on the remote control (20) to change between the following bands: FM1, FM2, FM3, AM1 and AM2.
Recalling a Station 1. Select a band (if needed). 2. Touch an on-screen preset button (6) to select the corresponding stored station. Auto Store (AS) Automatic Storing of Preset Stations To select six strong stations and store them in the current band: 1. Select a band (if needed). 2. Touch AS (17) for 2 seconds to activate the Auto Store function. The new stations replace stations already stored in that band.
- Network Tracking receiption uses the PI and AF codes. The PI code identifies the country, area and broadcast system. AF lists up which reception frequencies at the area are broadcasting the same program and automatically changes to the best reception quality offering frequency without the need to interrupt the program by a seek function. - Traffic programmes and announcements can be automatically received using the TA features. - The station name is displayed automatically when a RDS station is received.
- If the RDS station does not suport AF data list or if the tuner cannot read AF data from receiption, no network tracking is possible. Switching to alternative frequencies does not work. After turning the RDS feature on, AF can be set to become “ON” or “OFF” using the OSD menue. - AF “OFF”: When the AF switching mode is set to OFF and RDS is set to “ON”, a maximum number of 6 RDS and non-RDS channels will be stored together.
DVD PLAYER OPERATION NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen displays “PARKING” with a blue background. Rear video screens, if applicable, will operate normally. Opening/Closing the TFT Video Screen Opening the TFT Screen To open the TFT video screen, press the OPEN (2) button. The unit beeps and then open.
Accessing DVD Mode To switch to DVD mode when a disc is already inserted, press the DVD button (18) on the front panel or press the SRC button (8) on the remote control until DVD appears at the bottom of the screen. Using the Touch-Screen Controls The touch key areas for DVD playback are outlined below. A – Return to MAIN MENU B – DISP key: Displays playing information C – Select previous chapter D – Select next chapter E – Display the following on-screen controls: Menu, /II, , , , , .
Repeat Playback Press the REPT button (7) on the remote control to alter repeat mode according to the following: • DVD: Repeat Title, Repeat Chapter, Repeat Off • VCD (PBC Off): Repeat Single, Repeat Off • MP3: Repeat Single, Repeat Folder, Repeat Off NOTE: For VCD play, the repeat function is not available if PBC is on. Sectional Repeat Function (A-B) Use the A-B function to define a specific area of a disc to repeat.
Press the /II button (18) on the remote control or the ENTER (joystick) button (20) to confirm your selection and begin playback. Moving Through Chapters Press the button (19) on the remote control or the button on the joystick (17) to advance to the next chapter on the DVD. Press the button (17) on the remote control or the button on the joystick (16) to move to the previous chapter.
Table 8: Speaker Output options Speaker Setup Front Spkr Rear Spkr Center Spkr Subwoofer 2CH mode Play 2CH audio in 6CH mode with Surround “Off” Play 2-channel (down mix) audio in 6-channel mode with Surround I “ON” Play 6-channel audio in 6channel mode with surround II “ON” Goto Search During DVD or VCD playback, perform the following steps to use the GOTO feature to access a specific location on a disc: 1. Press the GOTO button (21) on remote control to enter “GO TO” mode. 2.
VCD Track Search Time – Go to specific time in the current track Track – Go to specific track VCD Disc Search Time – Go to specific time on disc Track – Go to specific track 3. Enter a time into the field using the numeric keypad (29) on the remote control. 4. Press the /II button (18) on the remote control or the ENTER (joystick) button (5) to go to the specified location on the disc. 5. Press the GOTO button again to exit.
Viewing an Alternate Picture Angle (DVD Only) Some DVDs contain scenes that have been shot simultaneously from different angles. For discs recorded with multiple angles, press the ANGLE button (13) on the remote control to toggle available angles of the on-screen image. Zooming Press the ZOOM button (23) on the remote control to enlarge and pan through the video image using the following options: “Q1”, “Q2”, “Q3”, and “OFF”.
Playback Information During DVD and VCD playback, press the DISP button (10) on the remote control to display playback information on the screen, including the media playing and current playback time. DVD Playback Information The following information is displayed at the bottom of the screen during DVD playback: • T : 5/8 – “5 / 8" indicates the fifth of 8 titles on the DVD is currently playing. • C : 2/16 – “2 / 16" indicates that the second of 16 titles on the DVD is currently playing.
VCD Playback Information The following information is displayed on the screen during VCD playback: • VCD2.0 – Format of current disc. • T: 6/18 – “6/18” indicates the sixth of 18 tracks on the VCD is currently playing. • 00:02:18 – “00:02:18” indicates the playback time of the current track. The following information appears on the screen during VCD playback in 6-Channel mode: • Front: DVD – “DVD” is the current playing source for the front zone.
General Disc Information Table 9: Disc Properties Symbol 12cm Disc Properties Max Play Time Single side single layer (DVD-5) Single side double layer (DVD-9) Double side single layer (DVD-10) Double side double layer (DVD-18) (MPEG 2 Method) 133 minutes 242 minutes 266 minutes 484 minutes Single side single layer (VCD) (MPEG 1 Method) 74 minutes Single side single layer 74 minutes Tabel 10: Disc Symbols Symbol Meaning Number of voice languages recorded.
Tabel 10: Disc Symbols Symbol Meaning Indicates the region code where the disc can be played.
Note: Once the DVD setup is complete, the settings are memorized. To return to the factory default settings, press the RESET button (25) on the front panel. Accessing a Menu To access a menu (LANGUAGE, VIDEO, AUDIO, SURR SETUP, SURROUND FX, or RATING), press the direction buttons on the joystick (6, 7, 8, 9) or remote control (14, 17, 18, 19, 22) to highlight the desired menu in green. You can also touch the onscreen menu selection to access that menu.
Selecting a Feature for Adjustment Once inside a menu, press the or II buttons (14, 22) on the remote control or the or buttons (6, 7) on the joystick to select the feature to be adjusted. Adjusting a Feature 1. Enter the option field for the feature you want to adjust by pressing the /II button (18) on the remote or by pressing the ENTER (joystick) button (5) on the unit. A submenu appears in a second row with the selected option highlighted in light blue. 2.
VIDEO Menu Features TV Shape (Aspect Ratio) 4:3 PS: With 16:9 display, the left and right sides are cut off. 4:3 LB: With 16:9 display, the top and bottom are cut off. 16:9: Image is presented in wide view with a 16:9 aspect ratio. Angle Mark On: Angle indicator (if applicable) is shown. Off: Angle indicator is not shown. View Mode Fill Original H Fit W Fit Fit to Scrn Pan Scan BACK: Return to previous menu.
Right Surr: Right surround channel pink noise Subwoofer: Subwoofer pink noise DRC Off/On: Employ the Dynamic Range Control for better playback for low volumes. CNTR CTRL 5ms/4ms/3ms/2ms/1ms/0ms: Adjust the time difference between the center and front speakers to create a time delay between 1 and 5 milliseconds, producing a more accurate audio effect.
SURR SETUP Menu To change speaker settings for 2-channel mode, use the or II buttons (14, 22) on the remote control or the or buttons (6, 7) on the joystick to select “DownMix”. To change speaker settings for 6-channel mode, select “Full 6CH”. After selecting 2 or 6-channel mode, use the button (19) on remote control or the button on the joystick (17) to move to the speaker settings on the right. Speaker Selection Selecting LARGE for the multi-channel speaker option will give a full range output.
SURR SETUP Menu Features FL (Front Left) / FR (Front Right) Large: Use when front speakers have good bass output. Small: Use when speakers do not have good bass output. LR (Left Rear) / RR (Right Rear) Large: Use when rear speakers have good bass output. Small: Use when rear speakers do not have good bass output. None: Use when rear speakers are not present. SUB (Subwoofer) Present: Use when subwoofer is present.
Dimension Ctrl 0-6: Shift audio output between front and rear speakers. Center Width Ctrl 0-6: Shift audio output between front and center channel speakers. BACK: Return to previous menu. NOTE: Surround I is recommended when the playback source is LPCM (Linear Pulse Code Modulation) or 2-channel down mixed digital bitstream. NOTE: When Surround I Music mode is selected, Dimension Control and Center Width are available for fine tuning to achieve a more realistic surround sound processing.
Load Factory Reset: Select “Reset” to restore the factory default settings for the Rating system only. BACK: Return to previous menu. To reset the password, access the “RATING” menu and enter the current password. Once the correct password is entered, you can access the “Password” field and enter a new one. NOTE: Record the password and keep it in a safe place for future reference. The rating for each disc is marked on the disc, disc packing, or documentation.
CD Player User Interface The on-screen indicators and touch key areas for CD playback are outlined below. 1. Current track and total number of tracks on disc 2. Elapsed playing time 3. Touch to activate/deactivate Repeat play mode 4. Touch to activate/deactivate Scan mode 5. Touch to activate/deactivate Random mode 6. Current time 7. Disc Title 8. Track Title 9. Touch to return to MAIN MENU 10. /II: Touch to play/pause disc playback 11. : Touch to stop disc playback 12.
MP3/WMA Discs This player allows you to playback MP3 files recorded on CD-ROM, CD-R, and CDRW. For CD-RW discs, please make sure it is formatted using the full method and not the quick method to prevent illegal disc operation. Use the following settings when compressing audio data for your MP3 disc: • Transfer Bit Rate: 320kbps • Sampling Frequency: 48kHz When recording MP3 up to the maximum disc capacity, disable additional writing.
MP3/WMA Playback Modes Play Mode Playback Details Disc Normal Playback all files on the disc and stop at the end. Disc Repeat Repeat playback of all files on the disc. Random Randomly play all files and stop at the end. Single Track Play a specific file and stop. Repeat Track Repeat playback of a specific file. Folder Normal Play all files in a folder and stop at the end. Folder Repeat Repeat playback of all files in a folder/directory. 4.
• • • • • • / : Play/Pause playback : Stop playback PAGE -: View previous page PAGE +: View next page DIR -: View previous directory DIR +: View next directory Controlling Playback Stopping Playback Touch the stop button ( ) on the screen or press the /BAND button (20) on the remote control to stop playback.
Moving Through Chapters Press the button (19) on the remote control or the button on the joystick (17) to advance to the next chapter. Press the button (17) on the remote control or the button on the joystick (16) to move to the previous chapter. Change Directory Touch the ( [DIR+] / [DIR-] ) key on the screen to navigate through the Directories / Folders Previous/Next Page Touch the ( [PAGE+] / [PAGE-] ) key on the screen to navigate through Pages / Files.
iPod OPERATION Accessing iPod Mode The unit will automatically switch to iPod mode when an iPod is plugged into the media module. To return to the iPod menu from any other source menu, press the SRC button (15 ) on the front panel or remote control (8) until the iPod menu appears on the screen. picture 1 Controlling your iPod by touch screen The left upper corner brings you back to the source selection menu.
Music Playback Press the button (19) on remote control, or the button on the joystick (9) to move to the next item on the menu. Press the button (17) on the remote control, or the button on the joystick (8) to move to the previous item on the menu. Press the /II button (18) on the remote control or the joystick ENTER button (20) on the head unit to select the highlighted menu option. Press the button (14) on the remote control or the button (6) on the joystick to return to the previous menu.
Fast Forward/Fast Reverse To fast forward or fast reverse, press and hold the or buttons (17, 19) for 1 second and continue to hold. Release to resume normal play. Search Playlist/Artist/Album/Song To search through Playlists, Artists, Albums and Songs, press the 1 button (29) on the remote control while in one of the following directories: Playlist, Artist, Album or Song. The selected directory will be accessed with the number of pages and files in that directory displayed at the top of the page.
TV TUNER OPERATION Accessing TV Mode To switch to TV mode, press the TV button (16) on the front panel or press the SRC button (8) on the remote control until TV appears at the bottom of the screen. NOTE: Touch the top left corner to access the MAIN MENU Multi-ZONE SETUP menu and the top right corner to access the Multi-ZONE menu (rear zone setup).
Using Preset Scan To scan stored stations: 1. Press the joystick button (5) to scan all stored TV stations. The unit pauses for 10 seconds at each station. 2. Press the joystick button again or press the /BAND button (20) on the remote control to stop scanning and play the current station. Selecting a TV Station To browse through stored stations: • Press the button (15) on the remote control or the button (6) on the joystick or to tune the previous stored station.
TROUBLESHOOTING GENERAL Problem Cause Corrective Action Unit will not power on - Radio Fuse blown - Car battery fuse blown - Illegal operation - Install new fuse with correct rating - Install new fuse with correct rating - Press the RESET button located in the bottom right corner of the front panel Remote control does not function - Battery depleted - Battery installed incorrectly - Replace battery with new one - Remove battery and install correctly No/low audio output - Improver audio output - Che
TFT MONITOR Monitor does not open automatically - TFT Auto Open is turned off - Turn TFT Auto Open on No image - Incorrect connection to par- - Check wiring and correct king brake wire - PRK SW is activated and - Stop vehicle in safe place parking brake is not engaged and apply parking brake Flashing image or inter- - DVD is not compatible with ference appears on current TV system settings screen - Improper video signal connections - Change setup to accommodate disc - Check wiring and correct Prolong
Problem Cause Corrective Action Disc does not play back - Disc is warped or scratched - Disc is dirty or wet - Laser pickup is dirty - Use disc in good condition - Clean disc with soft cloth - Clean laser pickup with cleaning disc - Incompatible disc is used - Use compatible disc - Disc rating exceeds Parental - Change Parental Lock settings Lock rating limit to lower restriction - Disc region code is not compati- - Use disc with proper region ble with unit code - Disc is inserted upside down - Insert d
Error Message Message Displayed Cause Corrective Action Loading - Disc is being read No Disc - Disc is dirty - Disc is upside down - Disc not present in loading compartment - Clean disc with soft cloth - Insert disc with label side up - Insert disc Bad Disc - Disc is dirty - Disc is upside down - Clean disc with soft cloth - Insert disc with label side up Unknown disc - Disc format is not compatible with this unit Region Error - DVD is not compatible with region code of unit Error - illegal
7. When the vehicle warms up during cold weather or under damp conditions, condensation may appear on the LCD panel. Should this occur, the screen will not operate properly until the moisture has evaporated. 8. We suggest you use a cleaning disc in this unit more frequently than in the unit in your home due to the environmental conditions of the vehicle.
D/A Converter(s): 6-channel high performance 24-bit, 192kHz, multi-bit Sigma Delta modulation. DAC supports sample rates from 8~192kHz. Electronic Skip Protection (ESP): 16Mbit high-speed flash memory DVD: 2-3 sec, CD-DA: 10 sec, MP3: 100 sec, WMA: 200 sec (ESP time is approximate) Video Format: NTSC, PAL (auto-detection) Output: 1Vp-p (75-ohm), buffered Input: 1Vp-p (75-ohm) FM RDS Tuner Tuning Range: 87.5MHz - 107.
Monitor Screen Size: • 6.5" (Measured diagonally), 16:9 Widescreen • 6.1" (155 mm) W X 3.51" (89.
D Wir gratulieren Ihnen! Durch Ihre kluge Wahl sind Sie Besitzer eines Audiovox Mobile Video-Produktes geworden. Audiovox Mobile Video-Produkte erfreuen sich aufgrund der hohen Qualität eines ausgezeichneten Rufes weltweit. Dieser hohe Qualitätsstandard ermöglicht es für Audiovox Mobile Video-Produkte 2 Jahre Garantie zu gewähren. Die Produkte werden während des gesamten Fertigungsvorganges laufend kontrolliert und geprüft. Im Servicefall beachten Sie bitte folgendes: 1.
G ARANTIEKARTE WARRANTY C ARD Typ/ Type Serien-Nr./Serial-No.
Audiovox Audio Produkte GmbH Lise-Meitner-Str. 9 · 50259 Pulheim Tel.: +49 2234/807-0 · Fax: + 49 2234/807-399 www.audiovox-germany.
