Model: CAM430MV Wired Multi-View Camera with License Plate / Rear Surface Mount Installation Manual Features Fully Adjustable, Multiple Viewing Angle Smart Camera.
Table of Contents Warnings ...................................................................................... 3 Product Description ..................................................................... 4 Packing List ................................................................................. 4 Operating Instructions .................................................................. 5 Camera Installation Instructions .................................................. 8 Camera Wiring Diagram .......
Warnings The product is intended to assist in safe driving and to allow the driver to have a broader rear view while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle.
Product Description This revolutionary camera uses machine vision technology and an advanced megapixel imager to allow you to choose between different viewing angles to get the optimum rear viewing experience. The system also includes a built in microphone so you can hear any warnings or noises from outside the vehicle if your monitor supports audio. The camera is easy to mount on your car, truck, or van with the bracket being hidden by your license plate.
Operation Instructions 1. Turning the camera on Place the gear from neutral to reverse position. 2. Change the camera view Press the MODE button The view changes each time when MODE button is pressed. The image will return to the default image next time the vehicle is placed in reverse gear.
Panoramic view: A wide angle field of view behind the car. Rear view: An undistorted view for reversing to parking area. Top view: Provide a undistorted top down perspective. Side view: Provide a divided image left and right perspectives in one view. Like looking up and down the street.
Changing the Image View Order & Default You can decide which view comes up as your default view and you can also change what order the views are seen when you press the MODE button. Whenever you hold down the MODE button for 5 seconds the current view becomes the default view – all other views are moved down in the order. This symbol comes on screen to confirm the change: EXAMPLE: So if you wanted to use “Rear View” as your default view and “Side View” as your 2nd choice then you would: 1. 2. 3. 4. 5. 6.
Camera Installation License Plate Mounting Instructions 1) Remove the rear license plate. Examine the vehicle to determine the best way to run the power wires to the reverse lights and the extension cable through the car. The Camera can be mounted above or below the plate. (For surface mounting with the included bracket, see the next section.) Determine the mounting location that best suits your needs. Be sure to verify that your installation plan complies with local laws and requirements.
Route the camera wiring into the vehicle. The wire can be run through an existing grommet, behind a tail lamp, under the trunk molding, or if necessary, through a 5/8 inch hole drilled near the vehicle’s rear license plate. When choosing a wiring path, make sure the cable will not be damaged or pinched, as this may cause a short circuit that is not covered by the warranty.
Surface Mounting Instructions 2) Find a suitable location on the vehicle where the bracket will not interfere with any equipment or doors, or block the line of sight. Verify that the planned mounting location is accessible from behind and that you have access to route the wiring inside the vehicle. Be sure that the mounting screws will not hit any wires or equipment inside the vehicle. 3) Attach the surface mounting bracket to the vehicle with the hardware included.
e) Coat the edge of the hole with rust preventative. f) Route the camera cable through the grommet and then through the hole. g) Insert the grommet in the hole to keep water from entering the vehicle. h) Remove the camera from the license plate bracket and attach it to the surface mount bracket on the vehicle. i) Adjust camera angle so that in standard reversing views you can see a small piece of the bumper and then tighten the mounting screws.
Camera Wiring If not using a ADVENT direct connect monitor please connect the red power lead to the positive of your White color back up light and the Black wire to vehicle ground. NOTE: If your vehicle has LED type backup lights you may be required to use a relay to power the camera as the vehicle circuit may not support the camera power. Connection to a low current circuit can cause a bad picture, no picture, or even a vehicle service lamp coming on.
Installing the dash mounted Control Button 1) Route the cable for the Control Button from the rear of the vehicle to the desired mounting location. Be sure to not block any Air Bag or safety device while routing the wire.Locate a suitable location for easy access for the driver. 2) Clean the area thoroughly and allow to dry before attaching the button. 3) Remove the backing paper from the adhesive pad mounted on the rear of the control button and press it firmly into position.
Software Configuration Mode (Setup) Preparation: In order for the camera angles and viewing areas to be correct for the vehicle it has been installed on, the camera must be set up correctly when first installed. You will be required to measure the vehicle width and the camera mounting height from the center of the lens to the ground. If the camera is not in the center of the vehicle you will need to measure the distance from center of the vehicle to the lens to determine its offset.
To enter configuration mode: 1) Press your foot on the brake pedal and then hold the "+" button, while placing the vehicle in reverse gear. 2) This will bring up the configuration menu on screen. 3) Press the “MODE” button to cycle between measurement units of centimeters or inches. 4) The first setting is the Camera Height Setting. Use the "+" or "-" buttons to set the correct height from the lens to the ground. Press “ENTER” button to complete this setting, and go to the next setting.
5) Vehicle Width Setting. This setting is used to adjust the space of parking guideline to be same as width of vehicle. Set the vehicle width by pushing "+" or "-" button. Press ENTER button to complete this setting, and go to camera center offset setting. 6) Camera Offset Calibration. The Offset setting is to adjust for Cameras that may be mounted off center on a vehicle. This will insure the parking lines are correctly matched to the vehicle position.
7) Image Mirror/Normal setting. If your image on your monitor is reverse and you need to flip the image press the "+" or "-" button to toggle through the choice. Press "ENTER" when finished. 8) Camera Angle Setting After you have installed the camera and adjust its angle and secured the mounting bolts, the camera angle setting allows for fine tuning of the viewing angle without having to physically change the camera angle.
9) After you finish the Angle Setting there should be an “ON/OFF” icon in the top corner of your screen. Take the vehicle out of reverse gear so the camera shuts down. Wait 2 seconds and then put the vehicle back into reverse gear. You should see an hour glass as all the changes are loaded. 10) Use the mode button to cycle through the different views and confirm that all is set up to your satisfaction. If necessary you can run the calibration again at any time.
Specifications •Voltage: +12V (9 ~ 16V allow) •Output image: CVBS, NTSC •Video Signal: 1.0Vp-p, 75ohm driver capacity •View angle Horizontal: 190° (Panoramic view), 130° (Rear view) Vertical: 150° (Panoramic view), 110° (Rear view) •Image Sensor: CMOS, 1Mega Pixel •Low lux: 0.
Add warranty in PDF 20
