® ELECT RONICS CORP. LCM5869NP & LCM7069NP Remote Controlled Color Display Monitor 5.8-Inch Color Display Monitor 7-Inch Color Display Monitor Installation and Owner's Manual Released: 03-27-02.
EXPLANATION OF GRAPHIC SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with the arrowhead within a triangle is intended to alert tell the user that parts inside the product are capable of producing an electric shock .
MATERIALS LIST 1. 2. 3. 4. 5. 6. 7. 8. System Monitor (LCM5869NP=136C2185) or (LCM7069NP=136C2184) Remote Control Unit (136B2156, used with LCM5869NP and LCM7069NP) with Lithium Battery, 3V,CR 2025 Interconnect Box (136B2183, used with LCM5869NP and LCM7069NP) Monitor Cable, 8' (112B3151, used with LCM5869NP and LCM7069NP) Headrest Mounting Tray (LCM5869NP=102C3739) or (LCM7069NP=102B3738) Trim Ring for Mounting Tray (LCM5869NP=102C3746) or (LCM7069NP=102B3745) Power Cable, 2.
SYSTEM OVERVIEW The LCM5869NP is comprised of a 5.8" Thin Film Transistor (TFT) Liquid Crystal Display ( LCD) Monitor. The LCM7069NP is comprised of a 7" Thin Film Transistor (TFT) Liquid Crystal Display ( LCD) Monitor. The Monitor for both of these systems have a 16:9 Aspect Ratio display that allows the user to select between two video sources (Not Supplied). The Monitors display all functions with the comprehensive On Screen Display (OSD).
NOTE: The following IRT board installation procedure should be performed between steps 10 and 11of the Headrest Mounting procedure on page 10. Insert the IRT boards into their respective compartments in the Headrest Mounting Tray and insert the plug into the IRT board. When the user switches the video source utilizing the ON/OFF/MODE switch, the A/B switch (see illustration below) on the IR2CHS Headphones must also be switched to select the desired audio source.
VEHICLE PREPARATION 1) Decide on the system configuration and the options that will be installed (i.e. what components, VCP, DVD, TV Tuner, Video Game, Monitor, FM Modulator, etc.). 2) Read the manuals and get familiar with the electrical requirements and connections. 3) Decide on the mounting locations and methods of mounting the products.
10) After verifying the proper operation of the system, proceed to mount each component. 11) The mounting method, and the location will vary from vehicle to vehicle; this manual will focus on typical Headrest installation procedures. 12) The best location for the system components is: a) Monitor: Headrest or bracket (optional) mounted onto a flat surface. b) System Interconnection Box (AVX-6869): In line with all the system cabling and in an area where it can be easily accessed.
2) Slide monitor onto Surface Mount Bracket and then tighten the fasten wheel. Monitor Fastener Wheel Surface Mount Fastener Mounting Bracket 3) Adjust viewing angle of monitor by tightening the fastener at the side. Surface Mount 4) When the system components are mounted, test the system to verify that it is functioning correctly. Make sure that no wiring was pinched, or connected improperly during the final installation.
Headrest Mounting: 1) Remove the headrest from the vehicle for easiest installation. 2) Lay headrest on a flat surface. 3) Center trim collar on headrest as shown. Monitor Mounting Tray Trim Ring Headrest NOTE: Depending on the angle of the headrest the Trim Ring and housing may be mounted upside down. 4) Using a permanent marker, mark headrest material along the interior of the Trim Ring. 5) Remove the Trim Ring and mark an “X” from corner to corner as shown.
6) Using the utility knife, cut the headrest material along the “X” lines. Do not cut the material along the other lines at this time. 7) This will leave you with an “X” cut as shown. 8) Pull the flaps up and cut the foam beneath the material to the proper depth. Cut all four sides of the foam. 9) Using your fingers, tear the foam out of the headrest leaving a recess where the shell will be inserted. NOTE: At this point you will need to install the harness up through the area into the recess.
NOTE: The Mounting Tray will need to be secured to the headrest, either by using tie straps, screws, etc. 10) Lay the flaps of headrest material down into the recess and insert the Mounting Tray into the recess. Check for fit. If it does not fit properly, you may need to remove some more foam. NOTE:If an Infrared Transmitter (optional) is to be installed it must be connected at this point as shown.
ELECTRICAL CONNECTION (Wiring Diagram) AV Output Video Source Input (1&2) Not Used AUDIO OX 11 128-6324 12 of 22
Monitor Removal: The following procedure is to remove the Monitor from the Mounting Tray using the supplied Removal Tool. NOTE: Use care when performing this procedure not to scratch any exposed surfaces with the edges of the Removal Tool. Masking tape applied to the two tips or legs of the Removal Tool will help prevent scratching. 1) Locate the Removal Tool and apply tape to the tips. 2) Insert the Removal Tool into the center of the space between the top outer Mounting Tray and the Monitor.
CONTROLS AND INDICATORS Headphone AUDIO OX OPERATING INSTRUCTIONS 1. POWER ON/OFF/MODE Press the POWER button to turn power on. Pressing the POWER button again momentarily will change video inputs. for NTSC input. Press the Press the for PAL input. Press and hold the POWER button for three seconds to turn power off. 2. Scroll Up Button This button is used to move Up through theselected menu items (Color,Bright, Tint, [NTSC] Only) this button will also switch selected items (DIM, RESET, FORMAT).
3. Scroll Down Button This button is used to move Down through the selected menu items (Color, Bright, Tint, [NTSC] Only) this button will also switch selected items (DIM, RESET, FORMAT). 4. MENU Button Press the MENU button once to display the menu On Screen Display. Press the button again until the desired menu item is highlighted. Use the or to adjust or switch the selected item. The On Screen Display menu will disappear if no buttons are pressed for four seconds.
REMOTE CONTROLLER NOTE: The Remote Controller supplied with this system is a standard remote control, which is used to operate other systems. The Remote Controller is not a universal remote and will only perform the functions described herein. Only the Keys highlighted on the Remote Controller image bellow are used to operate this system.
MENU FUNCTION KEY: The MENU Key is used to navigate between the Color, Bright and Tint adjustment modes. When the MENU Key is pressed an On Screen Display(OSD) will appear as shown bellow. COLOR BRIGHT TINT DIMMER FORMAT RESET OSD Press release and tap the MENU Key until the desired adjustment mode is selected. To return to the original settings select the RESET. When an adjustment mode is selected, press and hold the either the F or G (CH/DISK/SET) Key until the desired setting is reached.
VIDEO SOURCE MODE KEY: To switch between Video Input Sources (AV1 and AV2) press and release the MODE Key. NOTE: Select either *NTSC or PAL, press the F or G Keys (CH/ DISK/SET).
Display Mode 1. Press MENU to get the On Screen Display (OSD). 2. Select FORMAT. or the to switch the screen aspect ratio. 3. Press the FULL: 16:9 picture is fully displayed. ZOOM: Picture is stretched vertically and horizontally.
Replacement of Remote Controller Battery: 1. 2. 3. Use a small coin to pry open battery holder from compartment. Remove old battery and put in a new one with positive sign “ + “ facing upward. Push compartment into position. Precaution: 1. Dispose of used battery properly. 2. Do not misuse battery by short - circuiting the “ + “ and “ - “ terminal or put it into fire. 3. Remove used battery from compartment to prevent leakage from damaged battery. 4.
SPECIFICATIONS LCM5869NP: LCD Panel Size (Diagonal) ................................. LCD Panel Format ............................................... LCD Panel Resolution ......................................... LCD Backlight Life ................................................ Image Aspect Ratio .............................................. Video Input Signal ................................................ Video Power Source ....................................................... Power Consumption ...
36 MONTH LIMITED WARRANTY Applies to Audiovox Mobile Video Products AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 36 months from the date of original purchase, such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair labor.