5.
Important Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied.
MATERIALS INCLUDED IN THIS PACKAGE: 1) 2) 3) 4) MMD154 Video Monitor with DVD player (P/N 136-4447) (1 pc) A/V Adapter Cable (P/N112-3841) (1 pc) Remote Control (P/N 136-4446) (1pc) Hardware Package: • M4.2 x 16mm Phillips Self Tapping ST Pan Head Washer Screws (10 pcs) • M4 x 8mm Phillips ST Pan Head Screws (8 pcs) 5) Universal Mounting Bracket (P/N 108-3963) (1pc) 1. ON 2. O FF A UT O 3. S POWER SOURCE SCREEN EJECT STOP PLAY . 4. 5. 5. 5.
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, RF Modulator/external amp, remote headphones, DVD, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting.
VEHICLE PREPARATION: 1) Locate a Battery and accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off). Also find a location that will provide a good grounding point. Generally, this wire can be found at the ignition switch or fuse-box. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related accessories.
TRIM RING INSTALLATION: Trim Ring 1) The trim ring is attached to the video monitor using the perimeter screw bosses. It is important that the screws used in this installation are not overtightened, and that the video monitor and trim ring are mounted in such a way that the assembly does not distort (or bend) when the mounting screws are tightened. The trim ring MUST be screwed to the unit. (Refer figure 1) Figure 2 Figure 1 2) The MMD154 is now ready to be mounted in the vehicle.
MOUNTING THE TRIM RING Roof Roof Support Headliner Mounting Bracket (4) Self-Tapping Screws (not supplied) Trim Ring Video Unit (5) #8 Flat Washers (5) #8x3/4” Self-Tapping Screws MMD154 PLAYER INSTALLATION 1. Battery + Lead (Yellow)* Connect to the positive terminal of the car battery. 2. ACC Power Lead (Red)* Connect to ACC power, powered when ignition key position is in ACC or run position. 3. Ground Lead (Black) Connect the lead to a good chassis ground on the car.
7. AUX A/V, Output An auxiliary A/V output is provided to drive an external monitor. This signal mirrors what's being shown on this player. The volume function does not affect the Auxiliary A/V Output. 8. Polarity Switch Slide to "-" position if your vehicle's door polarity is negative; slide to "+" position if your vehicle's door polarity is positive. Note: Make sure the switch is fully seated in the desired position. * Fuse power leads at the vehicle power source. To install the player: 1.
TROUBLESHOOTING SYMPTOM: REMEDY: No power at Video Monitor -Verify +12 VDC on Red wire at Yellow wire Power Harness behind video monitor. Verify ground connection with continuity test from known good ground to black wire at Power Harness Power but no video or sound -Verify that the correct source is selected (DVD, AV 1 or AV 2). Verify that the source is on and playing known good media. Verify connections at both ends of the source component harness.
© Copyright 2007 AEC 150 Marcus Blvd.
