MMD7HRPKG Two Specific Vehicle Headrests With 7" LCD Monitors and Built-In DVD Player for Rear Seat Entertainment Installation Guide 128-8280
IMPORTANT Installation of headrest products require careful planning and preparation. Be extremely careful of seats that have airbags built into them. Keep wiring away from any air bag wiring (usually identified by yellow connectors and yellow wire jackets). Damage to air bag wiring can result in personal injury to vehicle occupants. If you have any questions regarding wire routing or installation in a vehicle, please contact Audiovox Technical Support at 1-800-225-6074.
5) Audio Interface Box (P/N 136-4632) - (1pc) 6) Remote Control (P/N 136-4327) - (1pc) 7) AV Adapter Cable (P/N 112B3227) - (1pc) 8) Hardware Package Scews (P/N 100-2267) - (16pcs) 9) 2 Pin DC Power Cable (P/N 112-3667) -(1pc) 10) Cigarette Lighter Adaptor Power cable (P/N 112-3946) - (1pc) 11) Extension Cable, 8 Pin Din to 8 Pin Din Conn Green/Red (P/N 112-3944) - (1pc) 12) Extension Cable, 8 Pin Din to 8 Pin Din Conn Blue/Yellow (P/N 112-3945) - (1pc) 13) Post Tube 12MM (P/N 100-2508) - (2pcs) 14
MMD7HRPKG SYSTEM OVERVIEW 1) The MMD7HRPKG SYSTEM is a versatile audio / video system with built-in DVD player (MMD7HRM only) which includes two monitors, that can accept an Audio / Video input and independent AUX input. A separate audio output is provided for connecting an optional FM Modulator to the vehicle's radio. 2) The M1 Monitor (MMD7HRM) is comprised of a 7" TFT LCD monitor with built-in DVD player that allows the user to select from the DVD, and the AUX source.
9) Pivot the screen until a comfortable viewing angle reached. The internal lock limits the screen to a maximum adjustment of 30 degrees from closed position, the headrest itself can be tilted forward to help achieve a comfortable viewing position. Inner Ring Internal Lock Closed Position 10) Insert disc Disc Label Insert disc 30 degrees MMD7HRPKG: MMD7HRM Monitor only. 11) Eject disc Eject disc MMD7HRPKG: MMD7HRM Monitor only.
Headrest Installation Description Choose the headrest cover color to best match your vehicle interior.
6 7 8 9 Use a screwdriver to loosen the screw from the inner-bracket of the headrest. Push the headrest support inwards or pull them outward adjust the distance. 10 11 Use a screwdriver to tighten the screw after headrest support have been adjusted.
MMD7HRPKG SYSTEM Electronics Installation Guide Monitor Unit MMD7HRS (Satellite Monitor) MMD7HRM (Master Monitor) MMD7HRS Monitor (Satellite Monitor / M2) MMD7HRM Monitor (Master Monitor / M1) FIGURE 3 12 13 Cable 1 : Monitor Pigtail Cable 2 : Headrest Cable Peel backing off of double sided tape (4 places) on vinyl tabs and stick to plastic outer tray Match M1 monitor to M1 headrest Match M2 monitor to M2 headrest 14 15 8
16 17 Move the locking tab to right position to fully insert the monitor into the headrest With Screw (x6) 19 18 Adjust match your vehicle seatback dimension VEHICLE PREPARATION: 1) Read the manuals and get familiar with the electrical requirements and connections. 2) Prepare the vehicle by removing any interior trim necessary to gain access to the vehicle's wiring as well as all areas where interconnecting wire harnesses will be located. (Refer to the Installation Procedure).
3) Locate an accessory power source (+12VDC present when the ignition key is in the accessory and run positions. 0VDC should be present when the ignition key is in the OFF position), and a good ground. Generally, these wires can be located at the ignition switch or fusebox. (NOTE: Ensure that the switched power is fused at the source. Failure to do so may result in vehicle wiring damage.) 4) Run the wiring harnesses throughout the vehicle as necessary.
8) Verify proper operation of the system. 9) Make sure that no wiring is pinched, or connected improperly during the final installation.
For Customer Service Visit Our Website At WWW.audiovox.com Product Information, Photos, FAQ’s Owner’s Manuals © 2007 Audiovox Electronics Corp.
