Remote Control Security System Installation Guide

ManualsBrandsAudiovox ManualsAutomobile AlarmPRO-9600

PRO-9600

Installation Guide

Remote Control Security System

With Pager/Satellite Control Interface

Installation Instructions

Kit Contents

PRO-9600 Control Module

4 Channel Code Learning Receiver

2 Three Button Anti-Code Grabbing Transmitters

Six Tone Multi-Tone Siren

Starter Inhibit Relay w/Socket

Main Wiring Harness

Auxiliary Wiring Harness

Plug In Valet

Plug In 2/Pin Door Lock Harness

Plug In LED

2 Pin Accessory VSS Harness

4 Pin Shock Sensor Harness

Plug In Two Stage Shock Sensor

Pin Switch Hardware Bag

Installation Guide

Owners Guide

Prestige Platinum Warranty

Consumer Activation Form

Window Warning Decals

Summary of content (12 pages)

PAGE 1
PRO-9600 Installation Guide Remote Control Security System With Pager/Satellite Control Interface Installation Instructions Kit Contents PRO-9600 Control Module 4 Channel Code Learning Receiver 2 Three Button Anti-Code Grabbing Transmitters Six Tone Multi-Tone Siren Starter Inhibit Relay w/Socket Main Wiring Harness Auxiliary Wiring Harness Plug In Valet Plug In 2/Pin Door Lock Harness Plug In LED 2 Pin Accessory VSS Harness 4 Pin Shock Sensor Harness Plug In Two Stage Shock Sensor Pin Switch Hardware Bag
PAGE 2
The PRO-9600 is a full featured security system with on board paging technology that provides the consumer a direct link to their vehicle from anywhere in the world. This patent pending technology allows the user to operate the vehicle from any land or mobile telephone.
PAGE 3
VALET/PROGRAM SWITCH: Select a mounting location that is easily accessible to the operator of the vehicle. The switch can be mounted to the lower dash panel in the driver's area. Inspect behind the chosen location to insure that adequate clearance is allowed for the body of the switch, as well that the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the desired location and mount the switch by passing it through the panel from the underside.
PAGE 4
White w/ Black Trace Wire: Positive (+) Siren Output This is the positive siren feed wire. Route this wire through a grommet in the firewall to the siren location. Connect the White w/ Black Trace wire to the Red wire of the Siren. Secure the Black wire of the Siren to a known chassis ground or solid clean metal surface. Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis.
PAGE 5
Dark Green Wire: (-) Instant Trigger Zone 2 The Dark Green wire is the instant on ground trigger input wire. This wire must be connected to the hood and trunk pin switches previously installed. Note: This wire will be shunted when remote control channel 2 is accessed, (trunk release). This wire will remain shunted all the while there is ground present, and for 5 seconds after the ground is removed.
PAGE 6
2 Pin Auxiliary Harness: (Red Connector) The two pin auxiliary connector is used to control vehicle shut down from a paging theft command. See supplement for wiring information. Connecting The Dash Mounted LED: Plug the two pin white connector from the previously installed LED into the mating two pin white female connector shell of the control module.
PAGE 7
Connecting And Adjusting The Shock Sensor: Route the 4 pin cable from the previously installed shock sensor to the control module. Plug it into the mating 4 pin white connector shell located along side the 8 pin main harness connector of the control unit. Pre- adjust the previously installed Shock Sensor by first accessing the potentiometer setting screw and carefully turn this adjustment all the way counterclockwise. Now Turn the adjuster clockwise to the first notch on the module case.
PAGE 8
PAGE 9
THE FOLLOWING OPTIONS HAVE BEEN INSTALLED AND ARE CONNECTED TO THE ALARM AND PAGER OUTPUTS AS SHOWN ALARM PAGER CHANNEL 2 CHANNEL 3 CHANNEL 4 AUXILIARY OUTPUT 1 IS CONNECTED TO AUXILIARY OUTPUT 2 IS CONNECTED TO AUXILIARY OUTPUT 3 IS CONNECTED TO PRODUCT INFORMATION SERIAL # COUNTRY CODE DLR/DIST ID# INSTALLATION DATE VEHICLE INFORMATION VEHICLE YEAR VEHICLE MFG. VEHICLE COLOR LICENSE PLATE# VIN# 9 VEHICLE MOD.
PAGE 10
PRO-9600 MODULE
PAGE 11
PRO-9600 11
PAGE 12
VSS WIRING SUPPLEMENT The two pin auxiliary harness with the red connector shell provides a input signal to the control module from the vehicle's Speed Sensor ( VSS), and provides a low current ground switched output to control a shut down relay. The relay can be used to interrupt any circuit in the vehicle which will cause the vehicle's engine to stop running.