Owner's Manual

ManualsBrandsAudiovox ManualsKeyless Entry SystemsAudiovox PRO9644E

128-9317

1 of 16

Page 1

PATENTED: www.voxxintl.com/company/patents

FCC COMPLIANCE

This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including any interference that may cause undesired operation.

Warning!

Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority

to operate the equipment

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this

equipment. Such modications could void the user’s authority to operate the equipment.

Table Of Contents:

Features and Options Page 2

About Your "Code Hopping" Transmitters Page 3

Arming Your System Page 3 - 4

Protection While The System Is Armed Page 4 - 5

Disarming Your System Page 5 - 6

While The System Is Sounding Page 6

Intrusion Warning Signals Page 6 - 7

Push Button LED/Valet/Override/Programming Switch Page 7

Manually Overriding Your System Page 7 - 8

Programming Your Custom Override Code Page 8 - 9

Using The Custom Code Override Page 10

Eliminating the Normal Arm/Disarm Chirps Page 10

Remote Panic Operation Page 10 - 11

Additional Remote Function (Channel 3) Page 11 - 12

Ignition Controlled Lock/Unlock Page 12

Telematic Upgrade Page 12

Programming New or Replacement Transmitters Page 13

Transmitter Battery Replacement Page 15

System Functions At A Glance Page 16

Model PRO9644E

Owner’s Manual

Summary of content (16 pages)

PAGE 1
Model PRO9644E Owner’s Manual Table Of Contents: Features and Options Page 2 About Your "Code Hopping" Transmitters Page 3 Arming Your System Page 3 - 4 Protection While The System Is Armed Page 4 - 5 Disarming Your System Page 5 - 6 While The System Is Sounding Page 6 Intrusion Warning Signals Page 6 - 7 Push Button LED/Valet/Override/Programming Switch Page 7 Manually Overriding Your System Page 7 - 8 Programming Your Custom Override Code Page 8 - 9 Using The Custom Code Ov
PAGE 2
IMPORTANT! In order to provide the highest possible level of security to your vehicle, this system is equipped with selectable manual override circuitry. It is possible that you will need to manually override your security system if the transmitter becomes lost, or inoperative due to battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is necessary to fully understand the procedure required to enable your vehicle in such situations.
PAGE 3
YOUR " CODE HOPPING" TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter, and retransmit at a later time to disarm your system.
PAGE 4
SILENT ARMING - ACTIVE 1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid. 2. Press and hold the Lock button on the keychain transmitter for 2 seconds.  Dash mounted LED begins to flash slowly.  Parking Lights flash one time.  Siren will not sound. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired.
PAGE 5
left a door opened, the alarm will sound for six 30 second cycles, remain armed and ignore that triggered zone.  Whenever the system is armed, the dash mounted LED indicator will slowly flash. This serves as a visual deterrent to the potential thief. The LED is a very low current bulb and will not cause the vehicle’s battery to drain, even when left unattended for extended periods.
PAGE 6
 Headlight Illumination - Optional  Illuminated Entry Upon Disarm SILENT DISARMING 1. As you approach the vehicle, press and hold the Unlock button on the keychain transmitter for 2 seconds.  Dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is rearming automatically. Open any door to suspend the automatic arming.  Parking Lights flash two times.
PAGE 7
 If the LED is flashing one time...pause...one time...pause...etc., then an intrusion attempt was made to the shock sensor, or an accessory triggering device that may have been added to the system.  If the LED is flashing two times...pause...two times...pause...etc., then an intrusion attempt was made to a hood or trunk pin switch that was added to the system, or to a light activated entry point if the alarm was installed using the voltage sensing feature.  If the LED is flashing three times...pause...
PAGE 8
3. Within 5 seconds, press and release the PBLED override switch. The alarm system will stop sounding and enter the (bypassed) mode. You can now start and operate the vehicle normally. Typically this override mode is used only if the transmitter has become inoperative. Programming Your Custom Override Code: Unlike override switches easily found, and defeated, this security system allows the consumer to program a personal override code, offering a higher level of security.
PAGE 9
Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3. Within 10 seconds, press and release the PBLED switch, 3 times. 4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5.
PAGE 10
MANUALLY OVERRIDING YOUR SYSTEM USING THE CUSTOM CODE OVERRIDE Assuming the override code programmed has not been changed, and the default override code of 11 is in the system's memory. 1. Enter the vehicle and turn the ignition switch to the on position. NOTE: The siren will sound. 2. Within 5 seconds, press and release the PBLED switch 1 time. 3. Within 5 seconds, turn the ignition switch off then on. 4. Within 5 seconds, press and release the PBLED switch 1 time. 5.
PAGE 11
1. Press and hold the ARM or DISARM button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound. 2. To stop the alarm, press and hold the ARM or DISARM button on the transmitter again for 3 seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds. Also if any transmitter button other than the ARM or DISARM button is pressed and released, the Panic mode will be turned off immediately.
PAGE 12
To activate the optional accessory, press the programmed button on the keychain transmitter for up to 8 seconds for continuous output, or press and release for momentary activation. The optional accessory will immediately engage. Check with your installation center for more information on the optional accessory that may have been installed and how it is accessed.
PAGE 13
PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS (BANK 1) The Transmitter Model Name 143BPr Is Also Found On The Back Of The Transmitter Case Battery Use CR2032 1. Turn the ignition key to the on position. 2. Press and release the valet/programming switch 3 times (Siren Chirps). 3. Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren. 4. Turn the ignition switch off.
PAGE 14
Two Vehicle Operation From One Remote Control This remote has the ability to operate 2 similar alarms from a single remote transmitter. To toggle on and off vehicle one or two,,, Press the Trunk/Key button + the Lock button for 5 seconds. The LED flashes 2 times. Release the buttons, to select 2nd vehicle mode. Program this transmitter into the second vehicle's system. Any time you are in 2nd vehicle when the transmitter is operated, the LED will flash twice for each function.
PAGE 15
Transmitter Battery Replacement: 1. Locate and remove the "00" point philips head screw on the back of the transmitter case. 2. Carefully separate the front case from the rear. 3. Slide the CR2032 battery out from under the battery clip and dispose of properly. 4. Install the new battery with the (+) side facing up away from the circuit board. 5. Close the case and reassemble in reverse order of disassembly.
PAGE 16
PRO9644E SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN CHIRP INDICATORS *1 CHIRP *2 CHIRPS 3 CHIRPS 4 CHIRPS = = = = ARM DISARM ARM / DOOR OPENED DISARM / INTRUSION * These chirps are optional, and can be de - activated.