VM9114 Operating Instructions CLOSE PIC WIDE TILT VM9114 160 Watts A/V INPUT 160 watts peak 40W x 4
VM9114 CONTENTS Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen VM9114 Mobile Multimedia Receiver for maximum enjoyment. Features ................................................................................................................................ 1 Controls and Indicators ........................................
VM9114 iv
VM9114 FEATURES Congratulations on your purchase of the Jensen VM9114 Mobile Multimedia Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen VM9114 installed by a reputable installation shop.
VM9114 • Rotary Encoder Audio Control WARNING! Never install this unit where operation and viewing could interfere with safe driving conditions. WARNING! To reduce the risk of a traffic accident (except when using for rear view video camera) never use the video display function while driving the vehicle. This is a violation of federal law. WARNING! Never disassemble or adjust the unit. WARNING! To prevent injury from shock or fire, never expose this unit to moisture or water.
VM9114 CONTROLS AND INDICATORS 1. CLOSE/OPEN Press to activate the automatic mechanical system and move the TFT monitor into viewing position. Press again to close the TFT. 2. PIC/BAND Press to adjust the Brightness and Contrast (see “Image/Display Settings” on page 6). With the monitor closed, press BAND to change between three FM and two AM bands. 3. DISC SLOT 4. WIDE/ | With the monitor closed, press to seek backward.
VM9114 Press and hold to activate the LOC feature. Repeat to deactivate. 12. RESET Press to reset system settings to factory default (except the password and parental lock setting). 13. A/V Input Attach a compatible A/V device.
VM9114 USING THE TFT MONITOR Open/Close TFT Monitor Open TFT Monitor Press the OPEN button (1) on the front panel to activate the mechanism that moves the display panel into the viewing position. Close TFT Monitor Press the OPEN button (1) on the front panel to load the display panel back into the compartment. TFT Monitor Auto Open If “TFT Auto Open” is “on” when the unit is turned on, the monitor automatically moves to the viewing position.
VM9114 Aspect Ratio Press and hold the WIDE button (4) on the monitor to adjust the aspect ratio as follows: FULL The entire screen is extended horizontally to the aspect ratio of 16 to 9. The extension ratio is the same at any point. NORMAL The conventional display image has a 4 to 3 ratio of horizontal to vertical, leaving a blank area on the right and left sides of the display. STANDBY Screen becomes black. Touch screen to resume.
VM9114 3. Press the PIC button on the monitor (2) 1-3 times to exit the picture adjustment menu. Parking Brake Inhibit When the pink "Parking" wire is connected to the vehicle Parking Brake circuit, the front TFT monitor will display video when the Parking Brake is engaged. (When the pink wire is grounded via the Parking Brake circuit, video will be displayed.
VM9114 OPERATING INSTRUCTIONS Power On / Off Press the /SRC button (10) on the unit to turn the unit on. You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen. Press and hold the button to power off the unit.The monitor is drawn back into the main compartment. Audible Beep Confirmation An audible beep tone confirms each function selection. The Beep tone can be disabled through the Setup menu.
VM9114 External Devices External peripheral devices, including a game console, camcorder, navigation unit, iPod, Zune, etc. can be connected to this unit via RCA output using an A/V Media Adapter Cable (not included). EJECT A/V INPUT 1 Right Audio 2 Left Audio Ground Video 3 4 3.5mm A/V Cable (not included) Connect the external device to the A/V Media Adapter Cable and then plug the cable into the A/V INPUT connector (13) on the front of the radio.
VM9114 Touch the EQ button on the left side of the screen to display the audio menu. Use the touch screen +/- buttons to adjust the settings for an audio feature. Table 3: Audio Adjustments Audio Function EQ BASS MID TREBLE FAD BAL Adjustable Range User Acoustic Urban Rave Latin Dance Hip Hop Rock -14 to +14 -14 to +14 -14 to +14 Grid Grid NOTE: The EQ mode will automatically change to “USER” when individual audio functions are adjusted.
VM9114 SETUP MENU To access system settings, touch the button on the screen to enter the “SETUP” menu. The “GENERAL” sub-menu appears highlighted in blue. RADIO 05:33 AM SETUP MENU General Rating Hardware P.VOL TS Cal DEMO Language Clock Mode Clock Tuner Region Beep Audio Back 12Hr 04 : 31 AM USA On Accessing Menu Items Touch the sub-menu name to select a sub-menu (Language, Audio, RDS, etc.).
VM9114 General Sub-menu Features Setting Options Function Clock Mode 12Hr 24Hr Clock displays 24 hour time up to 23:59. Clock (HH:MM) Clock appears in the top right corner of the screen during certain operations. NOTE: The AM/PM indication will change as you continue to adjust the hour past 12. Tuner Region USA • • • • AM Frequency Spacing - 10kHz AM Frequency Band - 530kHz~1720kHz FM Frequency Spacing - 200kHz FM Frequency Band - 87.5MHz~107.9MHz S.
VM9114 supported by the DVD, then the default language is used. Setting Options Function Language English On Screen Display appears in English. Subtitle English DVD subtitles automatically appear in English when available. Auto DVD subtitles appear according to the default subtitle language specified on the disc. Off DVD subtitles do not appear. Audio English DVD Audio is heard in English when the option is available. DVD Menu English DVD menu (if applicable) is displayed in English.
VM9114 To reset the password, access the “RATING” menu and enter the current password. Once the correct password is entered, you can access the “Password” field and enter a new one. NOTE: Record the password and keep it in a safe place for future reference. The rating for each disc is marked on the disc, disc packing, or documentation. If the rating is not available on the disc, the parental lock feature is unavailable.
VM9114 P.VOL Sub-menu Features Setting Source Options RADIO DISC Function Choose a source for which you would like to increase the relative volume (LEVEL). USB1 AUX Level 0-6 Increase relative volume for specified source up to 6 decibels. TS Cal (Screen Calibration) To access the “Screen Calibration” function from the SETUP menu, select the “TS CAL” option. After entering calibration mode, a crosshair appears in a corner quadrant of the screen.
VM9114 TUNER OPERATION Tuner TFT Display 8 17 RADIO 4 1 FM-1 10 2 9 19 3 01:02 PM P1 87.5 MHz ST E Q 5 LOC P1 87.5 MHz P2 90.1 MHz 14 20 P3 98.1 MHz 12 PS P4 106.1MHz P5 107.9MHz 13 P6 102.9MHz PS: 6 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
VM9114 Switching to Radio Tuner Source • • Touch the top left corner of the screen to view the SOURCE MENU. Touch “Radio”. Press the SRC button (10) on the front panel or remote control (8) to switch to the AM/FM or RADIO source. Selecting FM/AM Band Touch the BAND button (15) on the screen to change between the following bands: FM1, FM2, FM3, AM1, and AM2. NOTE: The BAND button on the unit only works when the TFT is closed.
VM9114 Using Preset Stations Six numbered preset buttons store and recall stations for each band. All six stored stations (P1-P6) for the current band appear on the screen. Storing a Station 1. Select a band (if needed), then select a station. 2. Touch the on-screen MEM button (18) to open the preset screen. Preset: _ P1 P2 P3 P4 P5 P6 Exit 3. Touch the preset number in which you would like to store the current station (or touch Exit to cancel and close the menu).
VM9114 Local Radio Station Seeking (LOC) When the Local function is on, only radio stations with a strong local radio signal are played. To activate the Local function in AM/FM tuner mode, press and hold the rotary encoder (11). When the Local function is active, the LOC indicator at the top of the screen is illuminated.
VM9114 DVD/VCD VIDEO OPERATION NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen display a parking brake notice. Rear video screens, if applicable, will operate normally. Opening/Closing the TFT Video Screen Opening the TFT Screen To open the TFT video screen, press the OPEN button (1). The unit beeps and then opens.
VM9114 Controlling Playback To access the on-screen controls, touch the bottom 1/3 of the screen while a DVD is playing. Touch the 1/2 button to view a second page of controls 1/2 AUDIO A-B SUBTITLE 1/2 TITLE MENU 2/2 DISP Stopping Playback Touch the stop button ( ) on the screen to stop DVD play. Pausing Playback Touch the play/pause button ( /||) on the screen to suspend or resume disc play.
VM9114 • VCD (PBC Off): Repeat Single, Repeat Off NOTE: For VCD play, the repeat function is not available if PBC is on. Sectional Repeat Function (A-B) Use the A-B function to define a specific area of a disc to repeat. • Touch the A-B button on the second page of DVD on-screen controls to set the start point (A) of the repeated section. • Touch the A-B button again once you reach the desired end point (B) of the repeated section. The selected portion of the DVD will now repeat continuously.
VM9114 Viewing an Alternate Picture Angle (DVD Only) Some DVDs contain scenes that have been shot simultaneously from different angles. For discs recorded with multiple angles, touch the button on the second page of DVD on-screen controls to toggle available angles of the onscreen image. Multi-Language Discs (DVD Only) Changing Audio Language If you are watching a disc recorded in multiple languages, touch the AUDIO button on the second page of DVD on-screen controls to choose a language.
VM9114 • Chapter 2/16 – Indicates that the second of 16 chapters on the DVD is currently playing. VCD Playback Information • VCD2.0 – Format of current disc. • Time 00:01:30/00:36:10 – Indicates the playback time of the current track. • PBC On/Off – Indicates whether Play Back Control is On or Off.
VM9114 Table 5: Disc Symbols Symbol Meaning Indicates the region code where the disc can be played.
VM9114 DVD/CD AUDIO OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and CD operation. Please see the DVD/Disc Video Operation section for information about these topics. The VM9114 will play music or other audio files from the following disc media: • CD-DA • CD-R/RW • DVD • DVD+R/RW • DVD-R/RW Upon inserting a disc with the TFT screen open, the disc and track title (if available), along with the track number and playing time appear on the screen.
VM9114 11. 12. 13. 14. : Touch to rewind current track : Touch to activate/deactivate Repeat play mode : Touch to activate/deactivate Random mode : Touch to access the direct entry screen 15. : Touch to view the SETUP menu 16. EQ: Touch for quick access to Equalizer level settings 17. Touch to view the SOURCE MENU and select a new playback source Controlling Playback Stopping Playback Touch the button to stop disc play. To resume playback, touch the /|| button.
VM9114 Fast Forward Touch the button to fast forward. Keep pressing and releasing the button to increase the rate from “x2” to “x4”, “x8”, and “x20”. Touch the /|| button to resume normal playback. Direct Track Entry To select a track directly, touch the on-screen entry menu. button to display the direct Chapter: _ _ 1 2 3 4 5 6 7 8 9 0 Clear Exit Enter Enter the desired track using the on-screen number pad. Press the Enter button to tune to the selected station.
VM9114 MP3/WMA OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and MP3 operation. Please see the DVD/Disc Video Operation section for information about these topics. Media and File Requirements This player allows you to play back MP3 and WMA files recorded onto CD-R/ RWs, DVD+R/RWs, and DVD-R/RWs. For CD-RW discs, please make sure it is formatted using the full method and not the quick method to prevent illegal disc operation.
VM9114 For example, a medium with the following folder/file hierarchy is subject to Folder Search, File Search or Folder Select, as shown below. The VM9114 player will only recognize three folder levels and does not display folders containing only other folders. In the example above, the unit will display folders 3, 4, 6, and 8, but not 2 and 7 since they do not contain any tracks directly. Folder 5 is not recognized at all since it is at the fourth level.
VM9114 To remove the USB device, press the SRC button (10) or use the SOURCE MENU to switch to another mode, and then remove the USB device from the connector. MP3 User Interface The on-screen indicators and touch key areas for MP3 playback are outlined below.
VM9114 11. : Touch to Fast Backward x2, x4, x8, x20 12. DIR -: Touch to view the previous folder 13. DIR +: Touch to view the next folder 14. : Touch to access the direct entry screen 15. : Touch to view the SETUP menu 16. EQ: Touch for quick access to Equalizer level settings 17. Touch to view the SOURCE MENU and select a new playback source 18. Folder name 19. 20. 21. 22. 23.
VM9114 Direct Track Entry Touch the page 28).
VM9114 TROUBLESHOOTING Table 6: Troubleshooting Problem Cause Corrective Action GENERAL Unit will not power on No/low audio output Radio Fuse blown Install new fuse with correct rating Car battery fuse blown Install new fuse with correct rating Illegal operation Press the RESET button located in the bottom right corner of the front panel Improper audio output connection Check wiring and correct Volume set too low Increase volume level Improper “MUTE” connec- Review wiring diagram and check t
VM9114 Table 6: Troubleshooting Problem Cause Corrective Action Prolonged image or improper height/width ratio display Improper aspect ratio setup Use correct aspect ratio setting Monitor stops at incorrect position Moving path is blocked Press OPEN key to restart monitor movement Auto antenna is not fully extended Connect the auto antenna control cable properly Auto antenna not properly connected Connect the auto antenna control cable properly LOCAL function is activated Turn LOCAL function o
VM9114 Table 6: Troubleshooting Problem Interruption occurred during playback Cause Corrective Action Disc is dirty or scratched Clean disc or replace File is damaged/bad recording Recreate disc with good files Error Messages Table 7: Error Messages Message Displayed Cause Corrective Action Loading Disc is being read No Disc Disc is dirty Clean disc with soft cloth Disc is upside down Insert disc with label side up Disc not present in loading compartment Insert disc Bad Disc Disc is dirt
VM9114 6. The CD player may not operate properly in extreme hot or cold. If such conditions occur, allow the interior of the vehicle to reach a normal temperature before using player. 7. When the vehicle warms up during cold weather or under damp conditions, condensation may appear on the TFT panel. Should this occur, the screen will not operate properly until the moisture has evaporated. 8.
VM9114 SPECIFICATIONS DVD/CD Player Compatible Disc Media: DVD + R / RW (Single and Dual Layer) and CD-R / RW Compatible Media Formats: CD-DA, MP3, WMA, VCD, SVCD, Xvid, AVI, MPEG 1/2 Signal to Noise Ratio: >95dBA Dynamic Range: >95dB Frequency Response: 20Hz to 20 kHz, -3dB Channel Separation: > 60dB @ 1 kHz D/A Converter: High performance 24-bit / 192 kHz sample rate, Multi-Bit Sigma-Delta Modulator Video Format: NTSC, PAL (auto-detection) Output: 1Vp-p (75-ohm) Input: 1Vp-p (75-ohm) FM Tuner Tuning Rang
VM9114 Amplifier Remote (Blue/White): 500mA max, current limited protection Operating Temperature: -20C ~ 65C Fuse: 15-amp, mini ATM type DIN chassis dimensions: 7" X 7" X 2" (178mm x 178mm x 50mm) CEA Power Ratings Power Output: 13 Watts RMS x 4 channels into 4-Ohms @ < 1% THD+N Signal to Noise Ratio: 70dBA below reference (Reference: 1 Watt, 4-Ohms) Frequency Response: 20 Hz - 20 kHz, -3dB. (Aux Input used as reference input) Reference Supply Voltage: 14.
VM9114 40
Audiovox Electronics Corporation Hauppauge, NY 11788 Technical Assistance: 1-800-323-4815 www.jensen.com © 2011 Audiovox Ver.
