VME 9120 TS Multimedia Receiver 1
CONTENTS Thank you for choosing a Audiovox product. We hope you will find the instructions in this owner’s ma nual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Audiovox VME 9120TS Mobile Multimedia Receiver for maximum enjoyment.
PREPARATION Congratulations on your purchase of the Audiovox VME 9120TS Mobile Multimedia Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Audiovox VME 9120TS installed by a reputable installation shop.
WARNING! Only connect the unit to a 12-volt power supply with proper grounding. WARNING! Never install this unit where operation and viewing could interfere with safe driving conditions. WARNING! To reduce the risk of a traffic accident (except when using for rear view video camera) never use the video display function while driving the vehicle. This is a violation of federal law. WARNING! Never disassemble or adjust the unit.
INSTALLATION ISO DIN Installation This unit is designed to fit into a 2.0 DIN dashboard opening, found in many imported cars. The unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of installation. 1.
Installation Using Mounting Sleeve 1. Install the sleeve. a. Install adapter if necessary (optional). b. Install sleeve into adapter or dashboard (use only the supplied screws). Do not force the sleeve into the opening or cause it to bend or bow. c. Locate the series of bend-tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard ope ning, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard.
After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). If unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis. 1. Connect wiring adapter to existing wiring harness. 2. Connect antenna lead. 3.
Subject to technical changes Wiring Diagram 8
CONTROLS AND INDICATORS Subject to technical changes 1. POWER/MUTE Press to turn the unit on. Press and hold to turn the unit off. When on, press to silence the receiver. Press again to resume the previous volume level. 2. SRC Press to select playing mode (SD, AV IN, DISC, Tuner). 3. VOL– Press to adjust the volume lower. 4. VOL+ Press to adjust the volume higher. 5. OPEN/EJECT Press to activate the automatic mechanical system and move the TFT monitor down to reveal the CD and SD Card slots.
Subject to technical changes Remote Control 10
Subject to technical changes
USING THE TFT MONITOR Open/Close TFT Monitor Open TFT Monitor Press the EJECT button on the front panel (5) or remote control (23) to slide the monitor panel down and reveal the disc and SD card slots. Close TFT Monitor Press the EJECT button on the front panel (5) or remote control (23) to close the monitor panel. Monitor Tilt Angle Adjustment A known characteristic of LCD panels is the quality of the display in relationship to the viewing angle.
OPERATING INSTRUCTIONS Power On / Off Press the / button (1) on the unit (or the button (4) on the remote control) to turn the unit on. Press and hold the button to power off the unit. The monitor is drawn back into the main compartment (if the Tilt function is in use). Audible Beep Confirmation An audible beep tone confirms each function selection. The Beep tone can be disabled through the Setup menu.
The Audio menu will automatically exit after a few seconds of inactivity. To exit quickly, touch the bottom left corner of the screen. Setup Menu (SET) To access the Setup Menu, touch the top left corner of the screen to view the SOURCE menu, and then select the “SET” option. The SET menu options are as follows: • LOUD OFF/ON: When listening to music at low volumes, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing.
OSD la nguage English G erman Spanis h Italian French English G erman Spanis h Italian French Select the appropriat e onscreen language for the DVD O ff Turn subtitles off DVD menu English G erman Spanis h Italian French Choose the language you would like DVD menu to appear in (if available) As pect Ratio 4:3 Image is presented with 4:3 16:9 Image is presented in wide view wit h a 16:9 aspect ratio. Subtitle Video Format NTSC The color signals are output in the standard NTSC format.
TUNER OPERATION Tuner TFT Display 1. Current radio band indicator 2. Radio frequency indicator 3. Clock 4. Preset radio stations: Touch to recall preset stations 5. Current Equalizer Mode 6. |<<: Touch to seek backward 7. >>|: Touch to seek forward 8. Touch to tune forward one step 9. Touch to tune backward one step 10. AS: Touch to automatically store stations 11. PS (Preset Scan): Touch to scan all stored preset stations, stopping for 5 seconds at each and continuinguntil a station is selected 12.
Recalling a Station 1. Select a band (if needed). 2. Touch an on-screen preset button (4) to select the corresponding stored station. Auto Store (AS) To select six strong stations and store them in the current band: 1. Select a band (if needed). 2. Touch AS button on the screen (10) for to activate the Auto Store function. The new stations replace stations already stored in that band.
DVD/VCD VIDEO OPERATION NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen displays “DO NOT WATCH VIDEO WHILE DRIVING” with a black background. Rear video screens, if applicable, will operate normally. Inserting a Disc To insert a disc, you must first press the /EJECT button (5) on the control panel or remote control (23) to reveal the disc slot (11).
Stopping Playback Touch the button on screen or on the remote control (14) to stop disc play. To resume playback, touch the /|| button on screen or on the remote control (19). Pausing Playback Touch the /|| button on screen or on the remote control (19) to suspend or resume disc play. Moving Through Tracks Press the >>| button on the remote control (18) or on screen to advance to the next chapter on the disc. Press the |<< button on the remote control (17) or on screen to move to the previous chapter.
To delete the list, highlight “CLEAR” and then press OK. Press PROG to exit the programmed playback screen. Remote Control Direct Track Entry To select a track directly, use the number pad on the remote control (27). For single digit entries, press the corresponding number. For two digit entries, press the 10+ button followed by the last digit (i.e., for track 16, press 10+ and then 6). GOTO Direct Track/Chapter Access Use the GOTO function to access a track (chapter) directly. 1.
Subject to technical changes Table 5: Disc Properties 21
DVD/CD AUDIO OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and CD operation. Please see the DVD/Disc Video Operation section for information about these topics.
Programmed Playback 1. Press the PROG button (34) on the remote control to access the programmed playback screen: 2. Use the or cursor buttons to access the fields on the “PROG” screen. 3. Use the number buttons on the remote control to enter a track number in each field. 4. Press the || button (19) on the remote control or highlight “PLAY” on screen and then press OK to begin playback in the numbered order indicated. To delete the list, highlight “CLEAR” and then press OK.
MP3/WMA OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and MP3 operation. Please see the DVD/Disc Video Operation section for information about these topics. Media and File Requirements This player allows you to play back MP3 and WMA files recorded onto CD-R/RWs, DVD+R/RWs, DVD-R/RWs and SD cards. For CD-RW discs, please make sure it is formatted using the full method and not the quick method to prevent0 illegal disc operation.
MP3 Player User Interface The on-screen indicators and touch key areas for MP3 playback are outlined below. NOTE: When burning MP3 / WMA files onto a DVD disc, use the 2X or 4X burning option, if available. This slower burning speed will help eliminate buffer errors and increase disc reading reliability. Also, use folders when burning large numbers of songs / files to a disc for easy music navigation. Select the "Disc at Once" option and close your disc.
Remote Control Direct Track Entry To select a track directly, use the number pad on the remote control (27). For single digit entries, press the corresponding number. For two digit entries, press the 10+ button followed by the last digit (i.e., for track 16, press 10+ and then 6). GOTO Direct Track/Chapter Access Use the GOTO function to access a track (chapter) directly. 1. Press the GOTO button on the remote control. The On Screen Display information will appear with the track number highlighted. 2.
TROUBLESCHOOTING Problem Cause Corrective Action Unit will not power on Radio Fuse blown Car battery fuse blown Illegal operation Install new fuse with correct rating Install new fuse with correct rating Press the RESET button located in the bottom right corner of the front panel Remote control does not function Battery depleted Battery installed incorrectly Replace battery with new one Remove battery and install correctly No/low audio output Improper audio output connection Volume set too low Imp
Image blurred, distorted, or dark Disc is illegally copied Use original disc PCB cannot be used during VCD playback PCB is not available on the disc while playing VCD PCB is on No repeat or searching Turn PCB off MP3 Interruption occurred during playback Incorrect playback message displayed Disc is dirty or scratched File is damaged/bad recording Clean disc or replace Recreate disc with good files Message is longer than LCD can display Subject to technical changes Care and Maintenance 1.
SPECIFICATIONS DVD/CD Player Compatible Disc Media: Media Formats: Signal to Noise Ratio: Dynamic Range: Frequency Response: Channel Separation: D/A Converter: DVD + R / RW (Single and Dual Layer) and CD-R / RW Compatible CD-DA, MP3, WMA, VCD, SVCD, AVI, MPEG1 / 2, XviD, and Kodak picture CD (JPEG).
D Wir gratulieren Ihnen! Durch Ihre kluge Wahl sind Sie Besitzer eines AUDIOVOX Mobile Video-Produktes geworden. AUDIOVOX Mobile Video-Produkte erfreuen sich aufgrund der hohen Qualität eines ausgezeichneten Rufes weltweit. Dieser hohe Qualitätsstandard ermöglicht es für AUDIOVOX Mobile Video-Produkte 2 Jahre Garantie zu gewähren. Die Produkte werden während des gesamten Fertigungsvorganges laufend kontrolliert und geprüft. Im Servicefall beachten Sie bitte folgendes: 1.
GARANTIEKARTE WARRANTY CARD Typ/ Type Serien-Nr./Serial-No.
Audiovox Audio Produkte GmbH Lise-Meitner-Str. 9 • D-50259 Pulheim • Germany Tel. ++49 (0) 2234 807-0 • Fax++49 (0) 2234 807-399 www.audiovox-germany.
