® ELECTRONICS CORP .
Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly to the operator of the motor vehicle.
MATERIALS INCLUDED IN THIS PACKAGE: 1) VOD701 (136D3428) Video Monitor with DVD (1pc) / VOD702 (136D3429) TV/Video Monitor with DVD (1 pc) 2) 12 Pin Power / Signal harness (P/N 112B2821) (1 pc) 3) 3 Pin Power Wire Harness with choke (P/ N 112B3274) (1 pc) 4) Aux-In pigtail (112B3227 5) Hardware Package #4 x 1/4” Screws (5 pcs) #8 x 5/8” Self Drilling Screws (4 pcs) #8 Washers (4 pcs) 6) Remote Control (P/N 136B3427) (1pc) 7) Mini Console (P/N 102C3916) (1pc) 8) 14 Pin FMM Cable (P/N 112B3273) (1pc) 9) FM Mo
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, Video Game, external amp, wireless headphones, VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting.
VEHICLE PREPARATION: 1) 2) 3) 4) Locate a constant power source (+12v at all times), an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off), and also a good ground generally, these wires can be found at the ignition switch or fuse-box. The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories.
MINI CONSOLE INSTALLATION: This page only covers special installation considerations for the mini-console installation. If the video monitor is to be installed in a vehicle with the mini console (P/N 102C3916 ), this console may need to be trimmed to fit the contour of the vehicle headliner. 1) 2) 3) 4) 5) In this installation, the video monitor is mounted directly to the overhead cross-member in the roof using the mounting screw bosses. These screw bosses should contact the cross-member directly (i.e.
MOUNTING THE MINI-CONSOLE Roof Roof Support Headliner 5"x9"x3/4" Plywood Block or Optional VOHBKT (4) Self drilling screws (not supplied) Mini-Console Video Unit (4) #8 flat washers (4) #8x3/4" self tapping screws -5-
VOD701 Hard Wired FM Modulator Output * REFER TO PAGE 8 FOR FURTHER DETAILS Red RCA (Audio Right) White RCA (Audio Left) 12 VDC Power and Ground Yellow RCA (Video) Satalite Radio FM Modulator 14Pin FMM Cable Item #8 TO FACTORY RADIO Am/Fm Antenna Dash Radio Power Connector 4 Pin IR LED: Clean the IR Receiver Window on the front of the VCP. Remove Adhesive Backing and Apply IR LED to IR Window on the Face of the VCP.
VOD702 Hard Wired FM Modulator Output Red RCA (Audio Right) * REFER TO PAGE 8 FOR FURTHER DETAILS White RCA (Audio Left) 12 VDC Power and Ground Yellow RCA (Video) Satalite Radio FM Modulator 14Pin FMM Cable Item #8 TO FACTORY RADIO Am/Fm Antenna Dash Radio Power Connector 4 Pin IR LED: Clean the IR Receiver Window on the front of the VCP. Remove Adhesive Backing and Apply IR LED to IR Window on the Face of the VCP.
VOD701/VOD702 INSTALLATION INSTRUCTIONS WHEN USING SATELLITE RADIO The VOD701/702 pods have dual IR transmitters. Channel A handles normal audio program material from A/V sources (DVD/AUX/TV, etc). The second B channel allows an external audio source such as Satellite Radio or a CD changer to be used through RCA input jacks. There are a variety of ways to wire this package as outlined below. Using an Audiovox SIRIUS satellite receiver 1) The modulator that is supplied with this package is model # FTR300.
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light.
Negative Switched Dome lighting To 12 pin connector Red / black - Lamp on Black / red - Lamp common Purple / brown - Lamp Auto To constant Factory Dome light circuit To constant Factory Door ajar switch or Body Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor -Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor.
For Customer Service Visit Our Website At WWW .audiovox.com Product Information, Photos, FAQ’s Owner’s Manuals 128-6695 © Copyright 2003 Audiovox Electronics Corp. 150 Marcus Blvd.
