WCC100 IN-VEHICLE CHARGING CRADLE 128-9237B WCC100 In-Vehicle Charging Cradle 12 03 13.
128-9237B WCC100 In-Vehicle Charging Cradle 12 03 13.
TABLE OF CONTENTS INTRODUCTION ��������������������������������������������������������������������� 2 Features ��������������������������������������������������������������������������������������������2 Trademarks ��������������������������������������������������������������������������������������2 IMPORTANT NOTICES ���������������������������������������������������������� 2 ICES-001 and NMB-001 Compliance Statement ����������������2 FCC Compliance Statement ������������������������������������������
INTRODUCTION Thank you for choosing the Audiovox WCC100 In-Vehicle Charging Cradle. The WCC100 In-Vehicle Charging Cradle utilizes Qi®(pronounced “Chee”) global interface standard for inductive electrical power transfer. Qi technology makes it possible to charge a Qi®-compatible mobile device via electromagnetic induction simply by placing the device into WCC100 Charging Cradle. There is no need to connect any cables.
IMPORTANT NOTICES FCC Compliance Statement This equipment has been tested and found to comply with the limits for a digital device, pursuant to Part 18 of the FCC Rules. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will occur in a particular installation.
CAUTIONS and WARNINGS CAUTION: The WCC100 In-Vehicle Charging Cradle is designed for in car use with an input voltage of 9VDC to 16VDC via a vehicle power outlet. Do not connect to higher input voltages. Use only the supplied power supply. CAUTION: Do not place metal between the mobile device and the WCC100 In-Vehicle Charging Cradle surface. Metal between the charging surface and the mobile device will increase temperature and stop the charging function.
MATERIALS INCLUDED IN THIS PACKAGE Open the box and ensure that the contents listed below are present. If any of the parts are missing, please contact: Audiovox Technical Support 1-800-225-6074. 1 2 3 4 Figure 1. Materials Included 1. WCC100 In-Vehicle Charging Cradle P/N 31512250 2. Windshield Suction Mount P/N 31512060 3. CLA Power Cable P/N 31512161 4. Owner’s Manual P/N 31512020 5 128-9237B WCC100 In-Vehicle Charging Cradle 12 03 13.
INSTALLATION INSTRUCTIONS 1. Remove the protective wraps from the windshield suction mount base (1) of the WCC100 In-Vehicle Charging Cradle. 2. Locate a smooth level area in the vehicle or position on the windshield so that it does not obstruct the driver’s view. Clean the area. 3. Press the windshield suction mount base (1) firmly against the mounting surface 4. Press the suction lever (2) down to secure the windshield suction mount to the mounting surface.
5. Remove the protective wraps from the charging cradle surface (3) and the brackets (4) of the charging cradle. 6. Mount the charging cradle to the windshield suction mount by sliding the clip (5) into the slot (6) on the rear of the wireless charging cradle. Move the wireless charging cradle upward to secure it to the windshield suction mount. 7. Adjust the charging cradle position for a comfortable viewing angle. 8.
OPERATING INSTRUCTIONS NOTE: Before charging your mobile device please read the mobile device manual thoroughly for charging parameters. 1. Open the brackets of the WCC 100 by pressing the release button (1), located on the backside of the charger. 1 Figure 4. Docking Brackets Open 2. Place your Qi-compatible mobile device upon the charger. Figure 5. Placing Device on Charging Surface 8 128-9237B WCC100 In-Vehicle Charging Cradle 12 03 13.
3. Fasten the mobile phone by pressing the brackets towards the phone. Figure 6. Device Locked onto the Charging Surface In the unlikely case, charging does not start automatically, retry from beginning. The integrated detection sensor will identify the Qi®-compatible mobile device when it is placed on the charging surface of the charging cradle. The charging process will start automatically. NOTE: Phone cases may interfere with charging.
The status of the WCC100 In-Vehicle Charging Cradle is displayed by the integrated LED (1). Refer to Charging Cradle Status Chart on page 11. 1 Figure 7. Charging Cradle 10 128-9237B WCC100 In-Vehicle Charging Cradle 12 03 13.
CHARGING STATUS WCC100 In-Vehicle Charging Cradle Status Chart Power OFF LED OFF Power ON LED Flashes Green Three Times Qi®- Device Detected LED Flashes Green Two Times Charging LED Lights Green Charge Complete Check Phone Charging Status.
12 MONTH LIMITED WARRANTY AUDIOVOX Electronics Corporation (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product, (at the Company's option) without charge for parts or repair labor.
WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY.
www.audiovoxproducts.com 128-9237B 2013 AUDIOVOX,150 Marcus Blvd. Hauppauge, NY 11788 P/N:7625000003C 128-9237B WCC100 In-Vehicle Charging Cradle 12 03 13.
