vehicle guide XMC-10A
Table of Contents 2 Table of Contents Congratulations ......................................................................... 3 FCC Information ........................................................................ 4 Cautions and Warnings ............................................................. 5 Contents XMC-10A ..................................................................... 6 Accessory Kit ..........................................................................
Thank you for purchasing the Audiovox Xpress XM® Satellite Radio Vehicle Kit. You are one step closer to experiencing the latest innovation in XM Satellite Radio. XM Satellite Radio will revolutionize your vehicle or in-home entertainment. XM is America’s number one satellite radio service with more than 7 million subscribers.
FCC Information 4 FCC Information Please note that the power cable that has been supplied with your device is supplied with permanently attached ferrite beads at each end. It is the responsibility of the user to use the cable with the ferrite beads. The user is cautioned that changes or modifications not expressly approved by XM ® Satellite Radio Inc. can void the user’s authority to operate this device. This device complies with Part 15 of the FCC Rules.
1. Do not install the XMC-10A vehicle cradle in a position that hinders your view through the windshield, or obstructs viewing of the dashboard indicators and displays. 2. Do not install the unit where it may obstruct the operation or deployment of safety devices, such as airbags, etc. 3. Do not allow operation of the unit to detract from safe driving practices; remember that you are responsible as the vehicle operator to adhere to all safe driving and traffic regulations. 4.
Contents 6 Contents XMC-10A Install Manual Cradle XMC-10A 1 pc. Antenna and Antenna Cable Exit Plug 1 pc. Cassette Adapter 1pc. 12 Volt-to-5 Volt DC Power Adapter 1 pc.
ACCESSORY KIT, MOUNTING Alcohol Cleaning Pad, Surface Cleaning Pad, Instruction Sheet, Swivel Bracket.
Installation/Wiring Precautions 8 Installation/Wiring Precautions 1. To prevent a short-circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation. Connect power wires last. 2. Do not install the unit in locations exposed to direct sunlight or, in areas subject to extreme temperatures. 3. Incorrect installation may cause damage to the system. Mount the unit firmly in place, using the supplied hardware. 4. Be careful not to damage the vehicle wiring. 5.
NOTE: The XM signal can be received and processed virtually anywhere as long as there are no obvious satellite signal obstructions such as nearby buildings, high terrain, parking garages or tunnels. 1. Cabling Interconnections You can begin to enjoy XM Satellite Radio as soon as the Xpress XM Receiver and Vehicle Kit installation are complete. Set up your Audiovox Xpress XM System using the following installation instructions, or enlist the help of a professional installer: 2.
Setting Up and Installing Your Kit 10 Interconnect Diagram NOTE: 1. IF THE XMC-10A IS INSTALLED USING THE OPTIONAL XMFM-1 FM DIRECT ADAPTER, DO NOT CONNECT AN AUDIO CABLE TO THE AUDIO OUT CONNECTOR OF THE CRADLE. XMC-10A CRADLE (LEFT SIDE VIEW) 2. THE FM MODULATOR OPTION MUST BE SET TO ”FM ON” IN THE XPRESS XM USER MENU.
XMC-10A CRADLE (REAR VIEW) XM ANTENNA XMC-10A CRADLE (RIGHT SIDE VIEW) OPTIONAL SURE CONNECT KIT XMSC1 (SOLD SEPARATELY) OPTIONAL SAT-RCA AUDIO CABLE (SOLD SEPARATELY) TO VEHICLE RADIO ANTENNA JACK (CONNECT TO AUXILIARY AUDIO INPUTS ON VEHICLE HEAD UNIT.
Setting Up and Installing Your Kit 12 CAUTION: Do not install the swivel bracket on a leather or fabric surface, or in a position that could impair your vision, block air bag(s) or obstruct vehicle dashboard controls and/or radio CD/cassette operational displays. NOTE: The adhesive backing on the bracket will not permit easy repositioning once it has been mated to the surface; use extreme care and planning when selecting the mounting location.
Remove the plastic liner from the adhesive backing on the bracket, and fix the base in position on the surface; make sure the mounting pad is accurately positioned on the first try, since repositioning may be difficult, if not impossible. f. If the bracket is to be screwed in place, do not remove the plastic liner from the adhesive backing. Use appropriate sheet metal or machine screws for this purpose. g.
Setting Up and Installing Your Kit 14 VERTICAL MOUNTING CONFIGURATION SIDE (HORIZONTAL) MOUNTING CONFIGURATION SWIVEL ADJUSTMENT SCREW XMC-10A CRADLE ASSEMBLY PLASTIC LINER AND ADHESIVE BACKING SWIVEL BRACKET SCREW HOLES (2) FOR DIRECT HARD MOUNTING
The XMC-10A Cradle can also be installed using other manufacturer’s mounts; the mounting plate provisions on the rear and bottom of the cradle provide you with two mounting options within the vehicle using various vehicle-specific aftermarket brackets. 4. Installing the Xpress XM Receiver into the Cradle Install the Receiver as follows: a.
Setting Up and Installing Your Kit 16 RECEIVER NOTCH Xpress XM RECEIVER SYSTEM CONNECTOR Xpress XM RECEIVER REAR VIEW RAISED DETENT CRADLE FRONT VIEW CONNECTOR GUIDE PIN XMC-10A SYSTEM CONNECTOR
The Xpress Receiver and Cradle provide an audio output signal in three ways: a. FM Modulator - When using the XMC-10A cradle with the FM modulator option, the XM audio signal can be received through your vehicle’s radio on selectable FM frequencies using the menu option included in your Xpress Receiver. (Refer to the User Guide.) The XM audio signal can then be played through your vehicle’s radio when that radio is tuned to one of the available frequencies. b.
Setting Up and Installing Your Kit 18 e. Xpress Cassette Adapter -The XM Xpress Cassette Adapter offers an additional audio connection option by utilizing your existing vehicle’s in-dash cassette deck. XM research and lab test results show that using a vehicle cassette adapter can best maximize the relationship between the best sound quality and ease of installation (see chart below).
4 3 2 1 Setting Up and Installing Your Kit Xpress Cassette Adapter Installation. Installation is simple. 1.) Plug the end jack (1) into the XM Xpress Car Cradle’s audio output (2). 2.) Insert the cassette adapter (3) in the vehicle’s in-dash cassette slot (4).
Setting Up and Installing Your Kit 20 6. Installation Guidelines Step 1. First, determine the proper location for your XM satellite radio antenna based on the following criteria for your specific vehicle: a. You must locate the satellite radio antenna on the top of the roof either in front of the rear window (option 1) or behind the windshield (option 2).
d. For option 1 and rear mounting locations, route the cable into the trunk as shown in the previous illustration. Always cross the weather seal at the lowest part of the trunk to reduce water leaks. From the trunk, route the cable into the passenger compartment through available wire channels and then along the floor under the door jam trim or under the carpet to the front of the passenger compartment. Do not leave the cable loose in the passenger compartment where it is likely to be damaged. e.
Setting Up and Installing Your Kit 22 Step 2. Once you have plugged the power and antenna jacks into the vehicle cradle, secure the cables with tape or wire ties to allow for a clean appearance. For example, secure the excess cable up under your dash board, between the seat and the console, or on the floor under a seat or floor mat.
Notes NOTES
Warranty 24 12 MONTH LIMITED WARRANTY AUDIOVOX ELECTRONICS CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 48 MONTHS FROM DATE OF ORIGINAL PURCHASE.
128-7472L
