AV due AV quattro AV 5.1k e AV du OWNER’S MANUAL CAR AUDIO STEREO AMPLIFIER Release 1.1 www.audison.
OWNER’S MANUAL AV due / Index 1. INTRODUCTION ............................................................................................................................................03 2. PACKAGING CONTENTS...............................................................................................................................04 2.1 Available accessories ................................................................................................................................04 3.
OWNER’S MANUAL AV due / 1 1. INTRODUCTION Coming directly from the know-how of the exceptional Thesis line, Voce components take the experience of listening in the car to a new level of excellence. Project innovation, advanced design, benchmark performance; the synthesis of consolidated know-how applied to car audio systems. The Voce project was born to make Thesis sound quality available to a wider - but no less demanding - audience.
OWNER’S MANUAL AV due / 2 2. PACKAGING CONTENT - AV due amplifier e AV du - Quick start guide - Warranty - nr.4 3,9 x 25mm / 0,15” x 0,99 self-tapping cross-headed fixing screws - N. 1 Allen wrench 0,118” - nr.1 60A AFS spare fuse - CD ROM with: This Owner’s manual (.pdf format) Test tracks TEST SIGNAL Track_01. sine sweep (10 min) Track_02. white noise (15 min) Track_03. pink noise (10 min) Track_04. sine wave 50 Hz - 0 dB (2 min) Track_05.
OWNER’S MANUAL AV due / 3 3. SAFE SOUND AUDISON AMPLIFIERS CAN BE PART OF A HIGH POWER AUDIO SYSTEM THAT CAN GENERATE VERY HIGH UNDISTORTED SOUND PRESSURE LEVELS. PLEASE REMEMBER THAT LONG EXPOSURE TO AN EXCESSIVELY HIGH SOUND PRESSURE LEVEL MAY DAMAGE YOUR HEARING; THEREFORE, PLEASE USE COMMON SENSE AND PRACTICE SAFE SOUND. Safety must be at the forefront while driving.
OWNER’S MANUAL AV due / 4 4. GENERAL PRECAUTIONS • This symbol indicates that you have to pay attention to these instructions. Disregarding them might cause accidental harms or damage your amplifier. • Before installing the amplifier, make sure you carefully read and understand all instructions. • The vehicle electric system must have 12V DC voltage with negative to ground. Make sure your car has it in order to avoid any damages to your amplifier and to the vehicle.
OWNER’S MANUAL AV due / 5 5.
OWNER’S MANUAL AV due / 6 6. REAR PANEL 1 + LEFT - 8 BATT GND REMOTE OUT IN CAP + RIGHT - 7 5 SUB VOL. CONTROL MONO: +L / -R 3 AV due 2 6 4 1. Protection fuse: 60 A; 2. Power (Ground): Terminal block for the amplifier power supply negative pole connection. Insert here the battery negative cable or wire connected to the vehicle chassis. The plug accepts cables up to 2 A.W.G.
OWNER’S MANUAL AV due / 6 6.2 HOW TO REPLACE THE FUSE 60A AFS Fuse (provided) + LEFT BATT GND REMOTE OUT IN CAP + RIGHT - SUB VOL. CONTROL MONO: +L / -R AV due 6.3 HOW TO CONNECT THE REMOTE SWITCH + LEFT BATT MONO: +L / -R GND REMOTE OUT IN CAP + RIGHT - SUB VOL.
OWNER’S MANUAL AV due / 6 6.4 REMOTE SWITCHING VIA SPK IN SUB REMOTE VOL OUT IN CAP BR REMOTE OUT to other amplifier - SP (1.2 K IN L - 20V) + R + INPU L T PR AR T ON MO OF NO F INPU EO UT L R T R L + PRE OUT - IN A L R + AR T ON OF F R 6.5 HOW TO CONNECT THE SUB REMOTE VOLUME CONTROL + LEFT BATT MONO: +L / -R GND CAP REMOTE OUT IN + RIGHT - SUB VOL.
OWNER’S MANUAL AV due / 7 7. FRONT PANEL 3 1. 2. 3. 4. 4 1 2 INPUT (0.3 - 5V): Left and Right analog inputs. PREOUT: Left and Right PREOUT output, corresponding to the Left and Right input signals. SPK IN (1.2V - 20V): High-level Left and Right analog inputs. ART (ON -OFF): If the source does not feature a 12V DC REMOTE OUT, set the ART switch to ON to turn on the amplifier plugging the cables to the SPK IN signal inputs. If the source features a 12V DC REMOTE OUT, set the ART switch to OFF.
R L SPK IN 12 Stereo signal SPK IN= Speakers IN (Hi Level) L R L N S LNS= Line Noise Suppressor PRE OUT R L A PRE IN 0.3 - 5,0 V RMS Levels 50-500 500-5k x1 x10 RANGE Hz Hi-Lo 12dB/Oct Lo 24dB Lo Hi L+R AUTOMATIC ON / OFF L R ext.pot SVC ST MO EXTERNAL Subwoofer Volume Control MO ST MODE Hi FULL Hi Lo FULL XOVER L R MO ST L+R MODE AMP AMP + RIGHT - - LEFT + OWNER’S MANUAL AV due / 7 7.
OWNER’S MANUAL AV due / 7 7.2 HOW TO CONNECT A SOURCE VIA PRE INPUTS - SP (1.2 K IN L 20V) + R - INP L + UT PR AR T OFF ON EO UT L R R PRE OUT 7.3 HOW TO CONNECT A SOURCE VIA THE SPEAKER IN HIGH-LEVEL INPUT - SP (1.
OWNER’S MANUAL AV due / 8 8. INPUT CONTROLS 8.1 CONTROL PANEL: SWITCHES AND ADJUSTMENTS 6 7 8 9 1 3 2 4 5 1. LEVELS (0.3V - 5V): LEVELS (0.3V - 5V): Input sensitivity of the Left and Right channel control. Set the knob on position 1. Use a CD as a source and increase the source volume until you hear distortion, then lower it slightly to eliminate distortion. Increase the amplifier LEVELS to optimize the output signal without distortion. 2.
OWNER’S MANUAL AV due / 8 8.2 SETTING UP FILTERS The AV due amplifier has a filter section versatile and completely independent between various sections. Once you choose a configuration you can easily adjust each pair of channels to your liking, allowing for a user-friendly set-up. Input Configuration AMP Full 1 MODE PRE OUT Full STEREO Config.
20 200 20 200 2K 20K Hz 20 200 2K 20K Hz 20 200 12 dB/Oct. 50÷500 OWNER’S MANUAL 50÷500 20 200 50÷1k 12 dB/Oct. 50÷1k 2K 20K Hz 3. AMP LO-PASS @ 12dB 20 200 2K 20K Hz 20 200 2K 20K Hz 2K 20K Hz 20 200 2K 20K Hz 12 dB/Oct. 12 dB/Oct. 2K MONO 24 dB/Oct. 50÷150 20K Hz 20 200 Full Range 20 200 12 dB/Oct. 2K 20K Hz 20 500÷5k 200 50÷1k 12 dB/Oct. 500÷5k 20 20 200 2K 20K Hz 2020 20 200 2K 20K Hz 20 50÷1k 200 200 200 20K Hz 20 12 dB/Oct.
OWNER’S MANUAL AV due / 8 8.3 EXAMPLE: PRE INPUT / PRE OUTPUT / LEFT AND RIGHT SPEAKER AV due INPUT PREOUT L L R R SPK IN (1.2 - 20V) - L + - R ART + ON OFF PREOUT to other amplifier R L Front PREOUT SOURCE REMOTE OUT IN BATT GND CAP SUB VOL. CONTROL AV due LEFT CHANNEL RIGHT CHANNEL FRONT AV due LEVEL (0.3 - 5V) ON TH 3 2 OVL SPK N.A.
OWNER’S MANUAL AV due / 8 8.4 EXAMPLE: SPK INPUT / PRE OUTPUT / LEFT and RIGHT Speakers AV due INPUT PREOUT L L R R SPK IN (1.2 - 20V) - L + - R ART + ON OFF PREOUT to other amplifier SPEAKER WIRE SOURCE REMOTE OUT IN BATT GND CAP SUB VOL. CONTROL AV due LEFT CHANNEL RIGHT CHANNEL FRONT AV due LEVEL (0.3 - 5V) ON TH 3 2 OVL SPK N.A.
OWNER’S MANUAL AV due / 8 8.5 EXAMPLE: PRE IN / PRE OUT / SUBWOOFER SPEAKER AV due INPUT SPK IN (1.2 - 20V) - L + - R ART + ON PREOUT L L R R OFF PREOUT to other amplifier R L Front PREOUT BATT GND CAP SOURCE REMOTE OUT IN SUB VOL. CONTROL AV due REMOTE VOLUME CONTROL OPTIONAL SUBWOOFER 2Ω SUBWOOFER ON 3 2 OVL SPK N.A. AV due LEVEL (0.
OWNER’S MANUAL AV due / 8 8.6 EXAMPLE: SPK IN / PRE OUT / SUBWOOFER SPEAKER AV due INPUT SPK IN (1.2 - 20V) - L + - R ART + ON PREOUT L L R R OFF PREOUT to other amplifier SPEAKERS WIRE SOURCE BATT GND CAP REMOTE OUT IN SUB VOL. CONTROL AV due REMOTE VOLUME CONTROL OPTIONAL SUBWOOFER 2Ω SUBWOOFER ON 3 2 OVL SPK N.A. AV due LEVEL (0.
OWNER’S MANUAL AV due / 9 9. ACCESSORIES: AV BIT IN AV bit IN M EN U D O W AV N U P EN IN AD Lin TE bi tI N R k OU T IN AC Lin k OU T Digital interface for all AV amplifiers. It allows a seamless digital connection with bit One and bit Ten D processors via the AD Link/AC Link connection. By inserting the AV bit IN “Digital Interface” into AV amplifiers, the digital signal in S/PDIF format, through the AD Link connection, leads directly to the high-quality internal D/A converters.
OWNER’S MANUAL AV due / 9 9.1 HOW TO INSERT AV BIT IN 2 1 3 4 5 WARNING: In particularly severe conditions the amplifier can reach temperatures between 80 and 90°C (176 ÷ 194°F). Make sure the temperature is not dangerous before touching it.
OWNER’S MANUAL AV due / 9 9.2 FRONT PANEL 1 AV bit IN IN 2 AD Link OUT IN AC Link OUT 1. AD Link: Digital audio bus that can transmit the signal of 8 channels. It exploits a Class 5 or 6 shielded cable for Ethernet networks normally used in computer networks. AD Link IN: RJ-45 input terminal to connect a digital signal coming from other AV amplifiers or other external devices equipped with AD Link (bit One / bit Ten D).
OWNER’S MANUAL AV due / 9 9.3 CONTROL PANEL DISPLAY AV bit IN MENU 1 2 DOWN UP 4 ENTER 3 See 9.5: How to configure AV bit IN 1. AV bit IN STATUS DISPLAY: This is the visual element of the AV bit IN system with a 3-character backlit LCD. While operating it can display all configuration parameters stored in the amplifier during the installation. The following pages contain all the messages and statements that may appear on the display from time to time. 2.
Remote Out to AV amplifier Remote IN AC Link / AD Link cables supplied with the products. * Use Don’t connect the remote input signal to the amplifiers when using AV bit IN module. ** ** AV bit IN AV bit IN AD Link IN OUT AD Link IN OUT AC Link IN OUT AC Link IN OUT * * * * to other amplifier to other amplifier OWNER’S MANUAL AV due / 9 9.
OWNER’S MANUAL AV due / 9 9.5 HOW TO CONFIGURE AV bit IN Before starting the configuration of the amplifier or amplifiers equipped with an AV bit IN digital input module, set and finalize the processor (bit Ten D / bit One) that will interface with the system. The processor channels specialized in “Digital output / AC Link - AD Link” will interface with the amplifiers equipped with the AV bit IN input module, as shown in the following procedure.
OWNER’S MANUAL AV due / 9 9.6 FULL DA EXAMPLE: FRONT + REAR + SUB with Audison bit Ten D processor AV bit IN AD Link IN OUT AC Link IN OUT DIGITAL OUT OPTICAL IN to other amplifier REMOTE OUT IN BATT GND CAP SUB VOL. CONTROL AV due LEFT CHANNEL RIGHT CHANNEL FRONT AV due LEVEL (0.3 - 5V) ON TH 3 2 OVL SPK Left e Right address 1-2 1 4 5 AV bit IN MENU DOWN UP ENTER bit Ten D Configuration N.A.
OWNER’S MANUAL AV due / 9 9.7 FULL DA EXAMPLE: WOOFER + TWEETER + SUB with Audison bit Ten D processor AV bit IN AD Link IN OUT AC Link IN OUT DIGITAL OUT OPTICAL IN to other amplifier REMOTE OUT IN BATT GND CAP SUB VOL. CONTROL AV due SUBWOOFER 2Ω FRONT AV due LEVEL (0.3 - 5V) ON TH 3 2 OVL SPK Subwoofer address 3 1 4 5 AV bit IN MENU DOWN UP ENTER bit Ten D Configuration N.A.
OWNER’S MANUAL AV due / 9 9.8 FULL DA EXAMPLE: FRONT + REAR + SUB with Audison bit One processor AV bit IN AD Link IN OUT AC Link IN OUT DIGITAL OUT to other amplifier OPTICAL IN REMOTE OUT IN BATT GND CAP SUB VOL. CONTROL AV due LEFT CHANNEL RIGHT CHANNEL FRONT TH 3 2 OVL SPK Left and Right address 1-2 AV due LEVEL (0.3 - 5V) ON 1 4 5 AV bit IN MENU DOWN UP ENTER bit One Configuration N.A.
OWNER’S MANUAL AV due / 9 9.9 FULL DA EXAMPLE: WOOFER + TWEETER + SUB with Audison bit One processor AV bit IN AD Link IN OUT AC Link IN OUT DIGITAL OUT to other amplifier OPTICAL IN REMOTE OUT IN BATT GND CAP SUB VOL. CONTROL AV due SUBWOOFER 2Ω FRONT TH 3 2 OVL SPK Subwoofer address 3 AV due LEVEL (0.3 - 5V) ON 1 4 5 AV bit IN MENU DOWN UP ENTER bit One Configuration N.A.
OWNER’S MANUAL AV due / 10 10. TECHNICAL SPECIFICATIONS POWER SUPPLY Power supply voltage: Idling current: Idling current when off: Consumption @ 14.4 VDC (Max Musical Power): 11 ÷ 15 VDC 1.7 A 0.02 mA 65 A AMPLIFIER STAGE Distortion - THD (1kHz @ 4Ω): 0.04 % Bandwidth (-3 dB): 4 ÷ 60k Hz S/N ratio (A weighted @ 1V): 100 dBA Damping factor (1k Hz @ 4Ω): 120 Input sensitivity: 0.3 ÷ 5 V RMS 15k Ω Input impedance: Speaker-In sensitivity: 1.
OWNER’S MANUAL All Specifications Subject to Change Without Notice AV due / www.audison.eu PART OF ELETTROMEDIA - 62018 Potenza Picena (MC) Italy - T +39 0733 870870 - F +39 0733 870880 - www.elettromedia.