User's Manual

Transducer Type Pre-polarized Condenser
Frequency Response 20 Hz - 20 kHz +/-2 dB
Polar Pattern Omni
Output Impedance 200 ohms
Sensitivity 6 mV / Pa @ 1k
Maximum SPL 130 dB with distortion <1%
140 dB Max
Signal to Noise Ratio 66 dB
Equivalent Noise Level 28 dB (A weighted)
Dynamic Range 112 dB
Connector male XLR
Power Requirements 24 - 48 V Phantom
Power Consumption 8.9 mA @ 48 Volts
Polarity Positive pressure on diaphragm
produces positive voltage on
pin 2 relative to pin 3 of output
XLR connector
Materials / Finish 4 piece precision machined
brass / Nickel Finish
Weight 132 g / 4.7 oz
Length 150 mm / 5.9 in
Hi
Lo
FREQUENCY RESPONSE
POLAR PATTERNS
ARCHITECT AND ENGINEER SPECIFICATIONS
The microphone shall be a back plate pre-polarized condenser with an
omni-directional polar pattern. The microphone shall operate on 24 - 48
Volts phantom power and the nominal output impedance shall be equal to
200 ohms at 1 kHz. The microphone shall have a sensitivity of 6 mV ± 3 dB /
Pa at 1 kHz. The microphone shall have a maximum SPL level of 130 dB with
a THD of 1%. The microphone shall be machined from brass with dimensions
of 19 mm diameter at the base, 7.7 mm diameter at the top and 150 mm in
length. The microphone shall be the Audix TM1.
OPERATION AND MAINTENANCE
The TM1 is a low impedance microphone and should be plugged into a
“mic level” input on your console, mixer or recording device. The TM1 will
NOT operate without phantom power voltage (24 Volts minimum) which is
available on most professional mic preamps and mixing devices. If phantom
power is not available on your equipment, you will have to purchase
a phantom power supply (such as the Audix APS2). Avoid plugging or
unplugging the microphone into a PA system unless the channel is muted
or the volume of the system is turned down. Failure to do so may result in a
loud “popping” noise which could seriously damage the speakers in the PA
system.
USER TIPS
Measurement: The TM1 is an excellent choice for room analysis programs
and real time analyzers. Just be sure that you are plugging the microphone
into a low impedance input and that phantom power is available.
Ambient room application: The TM1 may be used to capture the “room sound”
for in ear monitors. Typically, you would set up one microphone on each side
of the stage in a mic stand facing the audience.
Recording: The TM1 is extremely  at and accurate and has an excellent sound.
Because of its small pro le, it can be used in conjunction with portable
recording devices for live stereo miking. The TM1 is also excellent for miking
acoustic instruments and room ambience.
Further miking techniques may be found at www.audixusa.com.
ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
www.audixusa.com
503.682.6933 Fax: [phone]
Audix Corporation 9400 SW Barber St. Wilsonville, OR 97070
v 5.1
PRODUCT REGISTRATION: Please register your product online at www.audixusa.com/docs_12/about/product_registration.shtml.
SERVICE AND WARRANTY:
This microphone is under warranty for a period of 3 years to be free of defects in material and workmanship. In the event of a product failure due to materials or
workmanship, Audix will repair or replace said product at no charge with proof of purchase. Audix does not pay or reimburse shipping costs for warranty repairs or returns. The warranty excludes
any causes other than manufacturing defects, such as normal wear, abuse, environmental damage, shipping damage or failure to use or maintain the product per the supplied instructions. No
Implied Warranties: All implied warranties, including but not limited to implied warranties of merchantability and  tness for a particular purpose are hereby excluded. The liability of Audix, if any,
for damages relating to allegedly defective products shall be limited to the actual price paid by Dealer for such products and shall in no event include incidental or consequential damages of
any kind. Should your microphone fail in any way, please contact the Audix Service department at 503.682.6933. A Return Authorization is required before returning any product. OTHER THAN
THIS WARRANTY, AUDIX MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS, THE USE OF THE PRODUCTS, THE PERFORMANCE OF THE PRODUCTS. AUDIX SHALL
NOT BE LIABLE FOR SPECIAL INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES ARISING FROM OR BASED ON THE SALE, USE, STORAGE OR DISPOSAL OF THE PRODUCTS, AUDIX’S
SERVICE WORK, BREACH OF WARRANTY, BREACH OF CONTRACT. NEGLIGENCE, OR ANY OTHER THEORY OF LIABILITY, EVEN IF AUDIX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
DIMENSIONS (mm)
SPECIFICATIONS
TM1