Operator´s manual for the User ISDN PBX Systems COMmander쏐 Basic COMpact 4410 USB COMpact 2206 USB
Abbreviations used in the Manual CF Call Forwarding DDI Direct Dialling In number in case of a PTP connection Symbols used in the Manual Warning: Hazardous voltages will be present! Warning: General danger sign. GSM Global System for Mobile Communications PD Pulse Dialling DTMF Dual Tone Multi-Frequency dialling MSN Multiple Subscriber Number in case of a PTMP connection NT Network Termination unit for the basic connection ☞ N VoIP Voice over Internet Protocol T I Additional advice.
Table of Contents 3 Table of Contents Introduction ............................................................................................................................................................................................................... 7 Usage and Functionality ........................................................................................................................................................................................
Table of Contents Talking to a Visitor at the Door (Door Terminal Call) ........................................................................................................................................ 21 Your Telephone rings with the Door Bell Rhythm ................................................................................................................................................... 21 The Door Bell rings ..............................................................................
Table of Contents 5 You like to use the Wake-up Function of the PBX............................................................................................................................................. 35 Configure Wake-up Time and activate the Function for one single Wake-up......................................................................................................... 36 Configure Wake-up Time and activate the Function for repetitive Wake-up...............................................
Table of Contents Call Groups (Teams)............................................................................................................................................................................................. 52 Log in/out as a Member of a Group if you are only Member of one Group............................................................................................................. 53 Log in/out as a Member of a Group if you are Member of several Groups...........................
Introduction 7 Introduction Dear Customer! When you read this operation instructions probably the PBX has already been installed, started and absolutely configured to your requirements. In this case please take a little bit of time and read the instruction of this manual. Then simply try some of these functions and familiarize yourself with the PBX. If your requirements change in one way or another so that some settings need to be changed, please contact your authorized dealer.
왎 왎 왎 왎 왎 왎 왎 왎 왎 왎 Instructions for using the Manual Up to 57.600 bps data transfer (V.90) on the analog extensions. Exchange line reservation, pickup and explicit call transfer to an external phone. Dialling support by PC (TAPI). PBX software update via PC or telephone connection. Remote programming via exchange line from the outside.
Introduction If you find such a procedure described this way, execute the stated actions step by step from the left to the right. Symbols that are stated one under the other are at your disposal as an alternative. Depending on your functional goal, you can exchange these symbol against the symbol in the first row.
Telephoning Telephoning You like to react to an inbound Call The PBX is able to signal an inbound call in different ways, e.g. by a ringing telephone or by a knocking tone in the receiver of a busy telephone. If a telephone rings, you will often recognize where the call comes from. (For some of the ISDN telephones only „a long tone, pause etc.“ is possible.) In case of an analog telephone the external call can be signalled with e.g. „a long tone, pause etc.
Telephoning g f (F) conversation knocking tone (ignore with pulse dial) 0g 11 Refuse waiting caller to continue the current call undisturbed back to the current call ☞ If the waiting call is an Alarm call, the currently existing call will be terminated when accepting the waiting Alarm call. How to accept an alarm call is described on p. 22. If you have already a Query call when it knocks, at least one of both calls has to be finished first.
You like to separate the Charges of external Calls to different Accounts Call an external Number via Short-Code Dial Number (Dialling Assistance) bf internal dial tone (**) (for Direct Exchange Line Telephone only) k number of the Short-Code Dialling Number ☞ The PBX phonebook entries (number and name) are accessible from the phonebook menu of the system telephones COMfortel 1500/2500 and COMfort 1000/1200/2000 plus.
Telephoning Recall on no Reply: If the called person does not take the call, you will be able to reach him without repeating the call by starting a recall in case of no Reply. The function is possible for internal as well as external calls. The necessary ISDN feature „Call Completion on No Reply (CCNR)“ will be supported by PBX. 13 If you have started a recall, you will be called by the public exchange/ PBX as soon as the other subscriber hangs up after his next call.
You are Dialling a Number and are Hearing the busy Tone up in case of an external ringing may also be a signal for a missing calling authorization. If you always hear the busy tone after dialling a Short-Code Dialling number, this will point to a missing calling authorization mode or to a not programmed Short-Code Dial Number.
Telephoning 15 You are in a Conversation During a call different situations may occur e.g. you like to ask another person to this conversation issue or another caller tries to reach you. minal Portability“ up to 3 minutes in the public exchange. If you like to change the room during the parking, you are able to unpark the call with any other internal telephone again.
You are in a Call and like to Transfer it key/menu, you also will be able to use this comfortable operation (see manual of the telephone). If you are requested to enter the telephone number using the T-Net function, you will have to enter the Exchange 0 Line Access Number in case of external calls. The PBX supports also internal or Short-Code Dial Numbers as telephone numbers. Other internal Telephones are ringing (Pickup if you are in another Call) g (F) conversation (No.
Telephoning 17 Transfer a Call with prior Notice g (F) conversation (No. 1) 0r (ignore with pulse dial) Exchange Line Access Number and external number g external Query call (No.
You are in a Call and like to Transfer it If you hear the busy tone after dialling the internal telephone number, the telephone number is already in use for an „Open Query“. Use another configured telephone number for an „Open query“ - if it exists. If the called subscriber does not take the call (ringing period may be configured via configuration program COMset as ringing period for Blind Transfer) the call returns to your own telephone (your telephone rings).
Telephoning 19 You have two Calls (Query Call) During a Query you are talking to a subscriber while your first calling partner is put on hold in the background in the PBX. and listens to the Music on Hold. A Query is started by calling a Query partner, by using the Pickup function during a call or by accepting a waiting call announced by the knocking tone. Call Waiting Tone: The knocking during a Query is only possible with analog telephones.
You have a Conference Call Talk to both Call Partners at the same Time (Conference) g query call (no 2) (F) (ignore with pulse dial) 3g Start Conference call with both calling partners conference ISDN telephones and the system telephone a „ConferI With ence“ is started with an existing function key or via menu (e.g. with „conf“, „Conference“ or „3-party Conference“; see manual of the telephone).
Telephoning 21 Talk alternately with both Calling Partners (Alternation) g (F) 2 g Put 1st calling partner into the background (same condition as before Conference) g (F) 1g Put 2nd calling partner into the background (before Conference in a Query call) Conference Conference (ignore with pulse dial) (ignore with pulse dial) Query call No. 2 (as before the Conference) call No.
You like to take an Emergency Call The Visitor has not pressed the Door Bell Key bf internal dial tone (**) t telephone number of the door terminal (for Direct Exchange Line Telephone only) g Call door terminal door conversation You are in a Conversation and the Door Bell rings g conversation (No. 1) Y door bell rings (F) t (ignore with pulse dial) number of the door terminal g Start internal Query to call door terminal Query door conversation (No.
Settings 23 Settings 7Q Please pay attention to the fact that some functions may be forbidden or restricted via configuration program COMset for your telephone like e.g. the Call Forwarding. The programming functions starting with „7“ and the public password (default is „2“) are available and changeable by each user on his telephone. Some of these functions can be used on T-Net telephones with T-Net functions keys or menus and are not password protected.
You like to stay reachable during your Calls Activate automatic Configuration Switching b 7 O 80 S secret password 1: on, 0: off # ☞ After a power failure the time information is lost. In this case automatic switching and the Wake-up function will not be performed. After adjusting the time by the programming sequence on p.
Settings 25 Somebody should be reachable for internal/external Callers to your Telephone Number (Subscriber Call Forwarding) Thanks to the subscriber Call Forwarding (CF) you are able to forward internal and external calls that are targeted to your telephone to other internal telephones or external connections. You or your corresponding substitution can take these calls on another telephone.
Somebody should be reachable for internal/external Callers to your Telephone Number (Subscriber Call Forwarding) case of external telephone numbers. On the PBX you can also enter internal or Short-Code Dial Numbers as destination telephone numbers. key/menu, you will also be able to use this comfortable operation (see manual of the telephone). Then you will hear the acknowledgement tone instead of the public exchange announcement.
Settings 27 Programming Subscriber Call Forwarding via an external Telephone if you are „Out of Office“ b M external telephone remote switching and programming MSN/DDI 12 f tone (1 sec) continue with DTMF 1 7W f external password n „CF unconditional“ (for „CF on busy“ 13 instead of 12 and for „CF on no Reply“ 14 instead of 12) *n # f internal number of the target telephone or Start external Programming external acknowledgement tone (1 sec continuous tone) star and internal number of the te
External Callers should always reach Somebody when calling your external Number (MSN/DDI Call Forwarding) External Callers should always reach Somebody when calling your external Number (MSN/DDI Call Forwarding) If you like to be reachable always for external calls even if you are not at home at the moment and if nobody can take the call on the internal telephones, use the MSN/DDI Call Forwarding.
Settings 29 Switch the already configured MSN/DDI Call Forwarding on/off for an Exchange Line Telephone Number b7 Q 12 public password 1 **M „CF unconditional“ (for „CF on busy“: 13 instead of 12, „CF on no Reply“: 14 instead of 12) or # 2-times star and your own external number to be forwarded (without area code) 0 Switch on MSN/DDI Call Forwarding without entry of telephone number because number has already been saved Switch off MSN/DDI Call Forwarding Switch off all active MSN/DDI Call Forwar
☞ You do not like to be called You are in need of an analog DTMF telephone, an ISDN telephone with DTMF signalling or a DTMF sender. ment tone again. Now you can hang up the receiver or configure additional settings. The PBX needs to be configured for this operation with the configuration software COMset. If you failed to enter the sequence in time or entered the wrong sequence, you will hear a busy tone. In this case hang up the receiver and start again.
Settings 31 You like to save Call Charges with Least Cost Routing (LCR) The PBX enables you to call easy and without prior thinking via the cheapest available network provider. This is called automatic Least Cost Routing. To activate LCR on the PBX, the function has to be configured and the current tariff structure of the network providers has to be entered and stored.
You like to retrieve and analyse Call Charge Data ☞ The Call Allowance can also be managed with the PC program COMtools (p. 60). To use the function „Call Allowance“ without restrictions, you will need the feature „Advice of charge during the call (AOCD)“ for your ISDN exchange line. With „Advice of charge at the end of the call (AOCE)“ the PBX can only find out at the end of the call, if the Call Allowance has been exceeded.
Settings If you do not like to analyse your data on the PC, but like to send the data directly to a printer, you can connect directly a serial printer to the serial port. You have to configure the parameters of the serial port in the printer (no handshake, 9600 baud, 8 bit data, 1 stop bit, no parity). The following shortcuts/IDs are used in the printouts: * You should enter the start command as soon as the printer is connected. From this start point on, call data will be sent and printed unconditional.
You like to use the Serial Interface for Special Functions You like to use the Serial Interface for Special Functions The default factory setting is „no special function“. Other operation modes are: Dial with a PC telephone: An internal subscriber can use a PC dialler on a connected PC. This PC telephone needs to be configured in COMset. Continuous call data output: With this configuration, you can print your call data unconditional after the call to an attached printer.
Settings 35 You can enter „100-digit long Short-Code Dial Numbers“ with the PC software COMtools. These can contain letters and tokens to enter predefined messages to pagers. Enter public Short-Code Dial Numbers b 7 Q 31 m public password Short-Code Dial Number r 20-digit max.
You like to use the Wake-up Function of the PBX Configure Wake-up Time and activate the Function for one single Wake-up b 7 Q 76 U your telephone public password Ö time: 00-23 (hours), 00-59 (minutes) Day 1-7: Monday - Sunday or # 8 Set Wake-up time for Sat and Sun and activate for one single Wake-up on the first possible Wake-up time Saturday and Sunday or 9 Set Wake-up time for Mon, Tue, ...
Settings 37 Enquire Wake-up Time b 7 Q 79 # f your telephone Enquire Wake-up Time Output of the account digit by digit followed by acknowledgement tone (5th digit is the day of the week 1-7: Monday- Sunday 8: Saturday and Sunday, 9: Monday until Friday, 0: Every day) (Example: p.
You like to configure Ringer Rhythms and listen to the Result Listen to internal Dial Tones b 7 Q 96 public password and/or and/or and/or and/or and/or and/or ☞ 1 2 3 4 5 6 7 #f Listen to continuous dial tone selected tone Listen to PBX dial tone Listen to acknowledgement tone Listen to busy tone Listen to special dial tone Listen to ringing tone Listen to Call Waiting tone (knocking) If you have already test-listened to a tone it will be enough to for the next tone.
Settings 39 Configure Ringer Rhythm for internal Calls b your telephone 7Q public password 97 0 # 1 Change to ringer rhythm 1 x long 1 x long or Change to ringer rhythm 3 x short 3 x short Change Ringer Rhythm for external Calls b7O secret password 98 M Number or. MSN/DDI of your exchange line (without area code) * 0 # or or ☞ 1 Ü Set ringer rhythm „1 x long“ Set ringer rhythm „3 x short“ Set special rhythms No. 1-6 The default is 1 x long for each existing telephone number.
You want to listen into a Room (Room Monitoring) Configure Automatic Dialling / Hot Line b 7 Q 191 your telephone n public password # internal number of the target telephone or 0r Exchange Line Access Number and external number of the target telephone or k Switch on Automatic Dialling with entry of an internal subscriber telephone number as destination Switch on Automatic Dialling with entry of an external number as destination Switch on Automatic Dialling with entry of a ShortCode Dial Nu
Settings 41 Listen into the Room from an internal Telephone b fn internal telephone internal dial tone internal number of the Room Monitoring telephone f Perform the Room Monitoring from an internal telephone Room Monitoring Listen into the Room from an external Telephone b r f external telephone ☞ own remote switching and programming MSN/DDI Tone (1 sec) continue with DTMF 7W f external password external acknowledgement tone (1 sec continuous tone) 67# f Room Monitoring Perform the Room M
Use the Remote Switching Relay (via Telephone) Remote Switching via internal Telephone b7Q 6 public password 1: on, 0: off or or or or or ☞ 1 S # 2 3 4 5 6 On the system telephone COMfortel 1500/2500, COMfort 1000/ 1200/2000 plus and smar-tel-i (only on COMmander Basic) the relays can be switched comfortably via menu (see manual of the telephone).
Settings 43 You need to know the remote switching and programming MSN/DDI configured with the configuration program COMset. If you wait too long with entering the code sequence or enter the wrong code, you will hear the busy tone. Hang up the receiver and try again. If you call the PBX and enter the correct external password as described here, you will hear the external acknowledgement tone. Now you use the same programming digits as from the internal telephone (after the password).
You like to change the Music on Hold/Announcement 691 # f or or ☞ Activate alarm input for one single alarm external acknowledgement tone (1 sec continuous tone) 692 690 Activate alarm input for multiple alarms Deactivate alarm input You are in need of an analog DTMF telephone, an ISDN telephone with DTMF signalling or a DTMF sender. The PBX has to be configured properly with the configuration program COMset.
Settings 45 Recording the Music on Hold Announcement via Telephone (COMmander Basic only) b 7 O 441 # f secret password * g You will hear the acknowledgement tone ☞ start recording This function will delete the existing Music on Hold announcethe old ment directly. Even if you hang-up after dialling Music on Hold announcement will already be deleted. The Music on Hold announcement may have a maximum length of 8 seconds.
You like to change the Music on Hold/Announcement Select and listen to internal Music on Hold (COMpact 4410 USB and COMpact 2206 USB only) b 7 O 49 0#f # secret password or or or or or or or ☞ 1 2 3 4 5 6 7 you hear the music Select self-recorded music or pre-recorded .
Settings 47 Record the Alarm Announcement by Telephone and listen to it (COMpact 4410 USB and COMmander Basic only) b 7 O 442 # f secret password you hear the acknowledgement tone b 7 O 466 # f secret password you hear the announcement * g start recording Record the announcement. # stop recording # Record alarm announcement and store it Listen to the stored alarm announcement stop ☞ 442# With the recording function any existing announcement will be deleted unconditional.
Special Functions for Business Applications Special Functions for Business Applications The functions described in this paragraph are especially intended for the business applications. Nevertheless they could also be used in private homes to e.g. save money with Call Through. Reception and Secretary Function and Text before Answering Waiting Loop: This function offers an indirect transfer of an external calling partner to an internal subscriber if this one is busy.
Special Functions for Business Applications ☞ N The settings configured in the configuration program COMset concerning the call distribution remain to be unchanged. 49 These settings are configuration dependent (see p. 23).
Announcements via Loudspeaker and System Telephones Change private Password b 7 Q 38 V your telephone public password 0000 old private password (default: ) no password; so enter ☞ The digit „0“ is not allowed in the password. If the password needs to be shorter than 4 digits, the remaining unused digits will have to be filled with „0“ during programming. Example: You like to . You have to enter as „new password“ . use the password When telephoning later, you only need to enter as a password.
Special Functions for Business Applications ☞ On the called system telephone the LED next to the handsfree operation/loudspeaker/hook key (COMfortel 1500/2500 and COMfort 1000/1200/2000 plus) or the middle LED (smar-tel-i on COMmander Basic) glows and the connection is established after it rings once. 51 The announcement or the handsfree operation is limited to 120 seconds.
Call Groups (Teams) ☞ For safety reasons: There is a time limit for outbound external Call Through calls in the PBX (1-99 minutes). Call Through authorization. You can also configure in COMtools for each individual mobile phone number if Blocking numbers are used. COMpact 2206 USB or COMpact 4410 USB: Only a single Call Through connection is possible at the same time. The Call Through MSN that was configured in the configuration program of the PBX, must be known to you.
Special Functions for Business Applications busy or nobody takes the call or all the members are logged out - the call will be forwarded perhaps even to different destination numbers. If an „CF unconditional“ is activated in addition to a „CF on busy“ and/or a „CF on no Reply“, only the „CF unconditional“ is used that means the whole calls will be forwarded to the destination of the „CF unconditional“. In this case the other forwarding settings are ignored, but are still active in the background.
Call Groups (Teams) b telephone of the group member ☞ 7 Q 400 # public password Log out of all Groups If you try to „log in outbound and inbound“ into different groups, you will be only „logged in outbound“ in the last group tried. In the other groups you will be only „logged in inbound“.
Special Functions for Business Applications 55 Switch a previously configured Group Call Forwarding on/off b7 Q 12 public password 1*G „CF unconditional“ (for „CF on busy“ 13 instead of 12 or „CF on no Reply“ 14 instead of 12 or „CF if all members are logged out“ 15 instead of 12) star and internal number of the group to be forwarded # Switch on group Call Forwarding without entry of a telephone number because number has already been saved 0 or Switch off group Call Forwarding Switch off all act
Hotel Functions for Reception and Room Telephones 12 _0 „CF unconditional“ (for „CF on busy“: 13 instead of 12, „CF on no Reply“: 14 instead of 12, „CF if all members are logged out“: 15 instead of 12) 20 n internal number of the forwarded group ☞ *G star and internal number of the forwarded group #f external acknowledgement tone (1 sec continuous tone) You are in need of an analog DTMF telephone, an ISDN telephone with DTMF signalling or a DTMF sender.
Special Functions for Business Applications The configuration of the function is described in the installation and configuration manual of the PBX. ☞ Some providers do not transmit charge information. If a hotel guest is using such a provider to make outbound calls the accrued charges cannot be billed to him. Due to this reason it is not useful to activate Soft-LCR for a hotel room telephone.
Installation and Use of the bundled Software Installation and Use of the bundled Software Part of the product is a CD-ROM with various PC programs for use with the PBX. With the program COMtools separate PC programs can be launched. The programs con modify Wake-up times, Call Allowance accounts, Short-Code Dialling numbers, special numbers and the Music on Hold. The PC program COMlist will let you manage and analyse the data in the call data memory of the PBX.
Installation and Use of the bundled Software 59 Pic. 3: ISDN PC-controller on internal S0 port Pic. 5: ISDN PC-controller on internal S0 port (e.g. COMpact 4410 USB) Pic. 6: COMfort 2000 on internal S0 port Pic. 4: Connection: USB Interface (COMpact 2206/4410 USB) Installation of the Software 햲 Insert the CD-ROM (Auerswald Mega Disk) into the CD-ROM drive. 햳 Sometimes the installation will not be started automatically.
Functionality of COMtools Functionality of COMtools The program COMtools is a launcher for separate PC programs to use with the PBX. You can select between: 왎 A Short-Code Dial Number editor. (You can enter the Short-Code Dial Numbers and special numbers described later), 왎 A program to manage the Wake-up times (See chapter You like to use the Wake-up Function of the PBX on page 35). 왎 A program to modify the Call Allowance accounts.
Installation and Use of the bundled Software 61 Call Data Management with COMlist The PC program COMlist helps you to manage and analyse the call data in the call data memory of the PBX. The call data from the PBX is transferred to a data base and stored on the hard disk. The capacity of the data base is limited only by the size of your hard disk. Update Data Base To update your data base, select the menu „File...Read from PBX“. The data will be stored automatically after being transferred from the PBX.
Service Functions, Troubleshooting Service Functions, Troubleshooting Warning: Touching the voltage carrying conductors or connectors may be dangerous to life. As soon as the device is connected to the 230 Volt socket dangerous voltages may be present in the device (e.g. ringer voltage). - Installation work inside the open case as well as maintenance services involving the keys inside the case are only allowed to be executed by authorized personnel1. 1.
Service Functions, Troubleshooting 63 of cause. The update is free of charge: Only the cost for the necessary telephone connection is charged to you. After finishing the update you will be called to be informed about success/failure. If you listen to a busy tone instead of the acknowledgement tone after , the server port is busy. Put the receiver on-hook and try dialling again later.
Cleaning of the Casing Cleaning of the Casing Liquids entering into the case may cause a mortal electric shock or a damage or destruction of the unit. -When cleaning the case, make sure to prevent any liquid from dripping into the case. Protect the PBX against moisture, dirt, aggressive fluids or steam. Should a cleaning be necessary, wipe the case with a slight humid cloth or use an antistatic fabric.
Service Functions, Troubleshooting 햳 Check the curled cord of the receiver for defects. Telephoning impossible The most important requirement for telephoning is the presence of a dial tone after picking up the receiver. If this is not the case, the previous chapter will help you. If an external call is not possible with your telephone, please check, if this problem is also existing on other internal telephones or if dialling a different external number is possible.
Frequent Problem Sources Query or Transfer not possible Pressing the FLASH key disconnects the Caller 햲 The FLASH duration of the telephone is too long. Modify the settings of the telephone (see manual of the telephone) or the settings of the PBX with the function „learn FLASH time“ (see p. 63). Pressing the FLASH key leaves you in the first Call 햲 The FLASH duration of the telephone is too short.
Digit Code Index 67 DIGIT CODE INDEX Telephoning Alarm -> page 22 cbf0fa Start a call -> page 11 and page 49 Confirm alarm within 60 seconds with DTMF digit „0“ Announcement/Handsfree mode -> page 50 b (**) 660 n g b (**) 661 n g b (**) g Call System Telephone for InterCom Announcement Call System Telephone for InterCom/ Handsfree Mode Call Audio Output Call Through -> page 52 Mfrg M f *k g M f *n g M f *G g Call external connection through PBX Call external connection through PBX (using Short-C
Digit Code Index g (F) n f a f g (F) 7 f a Start internal call during an external call and hang up (Open Query) Put the external caller into the Waiting Loop if Transfer was unsuccessful g(F)670rga g g(F)4ng(F)0 Transfer external caller to external Telephone (External to External Transfer) Calling an internal third Calling partner and transfer to the second calling Partner.
Digit Code Index ... and immediatelya) switch on Subscriber Call Forwarding with entry of an internal telephone number as target. # 12 1n *n 12 1 *n # 12 0 *n # 20 n # a) 12 1 **M # 69 ... and immediatelya) switch on MSN/ DDI Call Forwarding without entry of telephone number because it has already been saved. a) ... and immediately switch on Subscriber Call Forwarding without telephone number entry because it has already been saved. 12 0 **M # 10 M # ...
Digit Code Index 7Q41S# 7Q42S# 7Q40SG# 7Q41SG# 7Q41S# 7Q42SG# 7Q400# 7Q480G# As a Group Member – Login as inbound only / logout from Group. As a Group Member – Login as outbound only / logout from Group. As a Member of multiple Groups – Login as inbound and outbound / logout from Group. As a Member of multiple Groups – Login into an additional group as inbound only / logout from Group. As a Member of multiple Groups – Login into all groups as inbound only / logout from all Groups.
Digit Code Index ... and switch on or off 1st Relay (COMpact 2206/4410 USB: „TS“ on slot B, COMmander Basic: „TS11/TS12“) 61S# 62S# 63S# 64S# 65S# 66S# ... and switch on or off 2nd Relay (COMpact 2206/4410 USB: „TO“ on slot B, COMmander Basic: „TO11/TO12“) ... and switch on or off 3rd Relay (COMpact 2206/4410 USB: „REL“ on slot B, COMmander Basic: „REL3 com/no/nc“) ... and switch on or off 4th Relay (COMpact 4410 USB: „TS“ on slot C, COMmander Basic: „TS21/TS22“) ...
Index I NDEX A C Abbreviations ............................................ 2 for call data ............................................. 32 Call ........................................................... 10 accept ..................................................... 10 alternation .............................................. 19 blind transfer .......................................... 17 make external ......................................... 11 make internal ..................................
Index Door Bell Key signalling ................................................ 21 Door Call start ........................................................ 22 start when door bell rings ....................... 21 Door Call incoming door bell rings ......................................... 21 telephone rings ....................................... 21 Door Functions ....................................... 21 door to external call ................................ 41 External Call Forwarding ..................
Index Printing Hotel Function ........................................ 56 884239 R-Key DTMF (FLASH-Key) ................................. 9 ISDN ......................................................... 9 Three-Party Call (Conference) finish ....................................................... 20 start ........................................................ 20 Room Monitoring .................................... 40 Time dependent Programming .............. 23 Room Status (Hotel Function) ....
Save the earth – 100 % recycled paper 884239 04 09/06