8 Insta II Download Follow the instructions in the Installation guide to replace your existing thumb-latch with your new August Smart Lock. Download the August App and create a user profile.
Calibrate Use Follow the instructions in the App to calibrate your August Lock with your Bluetooth enabled smart phone. For a compatibility list, visit august.com/phones. Operate your August Lock from the App or set up Auto Unlock to use handsfree. Invite and schedule guests.
Prep a ration Make sure your existing dead bolt is compatible with the August Smart Lock. Only standard deadbolts are supported. Use our compatibility assistant to double-check: august.com/compatibility TOOLS NEEDED ~ You will need a standard Phillips screwdriver. Alternately, we have a network of installers who can help with installation. august.
Compatibility YES Standard Deadbolt is mounted and operates independently of the door handle.
Package Contents 1 Adhesive Strip (Inside Envelope) 1 August Smart Lock (4 AA Batteries Pre-installed) 4 Adhesive Rubber Bumpers (Inside Envelope)
3 Adapters 3 Mounting Plates
Installation Overview Before Installation Key Hole Dead bolt Tail Piece ' Thumb-latch 0 Screws 8 Installation Gu1de 0
• After Installation 0 Key Hole f) Deadbolt 8 Tail Piece Mounting Plate 0 Screws 0 Tail Piece Adapter f) August Smart Lock & Faceplate Calibration Tape 0 0
Step 1: Prepare existing deadbo lt. Affix the supplied adhesive strip over the key hole, securing it to the exterior side of your door. This should hold the key hole in place when you remove the thumb-latch on the inside of the door. On some doors, such as those with glossy paint, the included tape may not be strong enough. In this case you should apply additional stronger tape to ensure that the key hole stays in place. Use caution.
Step 2: Remove your existing thumb-l atch. (i) Position your thumb-latch so that you can unscrew the existing screws on your deadbolt. Remove the screws entirely from the dead bolt and keep them to assist in the next step. After removing the screws, be sure to unlock your deadbolt before removing the thumb-latch . 0 Your thumb-latch may include an additional back plate underneath it. If so, remove the back plate. Use the back plate and the longer screws for the next step.
@ 0 @
Step 3: Se lec t the co rre ct mo un tin g plate and adapter. If you know the bran d of your dead bolt, pleas e selec t the corre ct mou nting plate and adap ter from the Com patib ility Char t on the next page , and then go to Step 4 (pag e 18). If not, go to Step 3a (pag e 16) to find the corre ct mou nting plate and adap ter.
Standard Deadbolt Compatibility Chart BRAND MOUNTI NG PLATE Baldwin - Estate/Images* Baldwin Reserve/Prestige 1 3 Defiant 2 Emtek 3 Kwikset" Omnia ··: 3 1 Schlage ·** 2 Weiser 2 Weslock 1 * Baldwin and Kwikset Deadbolt s installed before 1997 have unique installation requirem ents. please contact us at 844-AUGUST1 (284-8781) and we will walk you through installation. Compatib le only with non-mort ise, standard Omnia deadbolt s.
Step 3a: Select the correct mounting plate. Q Insert the existing screws in the thumb-latch to help you choose the correct mounting plate. If there was a back plate under your thumb-latch, insert the screws into this back plate instead of the thumb-latch. = Slide the mounting plates onto the screws one at a time until you find a mounting plate that allows the screws to fit straight through the holes.
1. 2. COMPATIBLE NOT COMPATIBLE Having trouble selecting the right mounting plate? Try august.
Step 4: Position the mounting plate. f) Remove the backing from the 4 rubber bumpers and place them on the back side of the mounting plate (the side that does not show a number). 0 Remove the screws from the thumb-latch and use them to install the mounting plate over the existing dead bolt tail piece. (9 Do not fully tighten the screws. Over-tightening can deform the mounting plate and interfere with the operation of the lock.
@ 0
Step 5: Position adapter and align mountin g plate. • Remove the tape from the key hole, and use your key to turn your dead bolt to the fully unlocked position. = If your lock was not in the Compatibility Chart, select the adapter that fits your tail piece. To do this, slide each adapter onto the tail piece. The correct adapter will have the small nub pointing up. (9 Place the correct adapter onto the tail piece with the small nub pointing up. Tighten the screws until they are just tight.
Front View @ 0 Deadbolt Tail Piece ~ Adapter Alignment Having trouble selecting the right adapter? Call August customer support at 844-AUGUST1 (284-8781)
Step 6: Attach the August Smart Lock. fl Insert the adapter into the back of the August Smart Lock, then position the August Smart Lock with the curved notch at the top. 0 Pull out both side wing latches. Slide the August Smart Lock over tail piece and attach to mounting plate. Make sure the back of the lock is flush with the door. (9 To secure the August Smart Lock, clamp down both side wing latches to the mounting plate completely.
@ 0
Step 7: Remove battery tab. (f) Press down on the face place and rotate it counterclockwise to open the battery compartment. (Don't remove the factory seal until instructed to do so during the calibration process.) @) Holding batteries in place, remove the plastic battery isolation tab. Make sure that the battery is properly seated in its compartment. 8 Align faceplate hooks with the August Smart Lock. The faceplate will lock into place with the logo at the bottom.
@ 0 @
Step 8: Install August App Download the App from august.com/app The app will help you create an account and set up your August Smart Lock. We suggest that you protect your phone with a passcode in case it is lost or stolen.
~ \:~lib tQt ~~ tlur 1 \)t~ @ 'l' '~ •'', ',,, 0
Limited Warranty Statement IMPORTANT: By using the August Smart Lock hardware (the "Device") you are agreeing to be bound by the terms of this Limited Warranty set forth below.
4. Scope of and limitation of Warranty. The warranty on this Device is limited to the repair or replacement of defective Devices as described in the limited Warranty section above. This warranty does not cover customer training and edu cation, installation, set up or adjustment, signal or reception problems. The August Smart Lock is not an ANSI or BHMA certified door lock and must be correctly installed and used with a certified door lock that is operating in good condition.
Compliance FCC GENERAL STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Safety Risk of explosion and personal injury if batteries are replaced by incorrect type. Do not open, mutilate, or expose to conducting materials (metal), moisture, liquid, fire or heat above 54° C (130° F), incinerate, or immerse in water or liquid of any kind. Do not short circuit. Doing so may cause batteries to leak or explode, resulting in personal injury. Dispose of spent, leaking. or damaged batteries according to manufacturer instructions and local laws. Do not mix battery types.
Specifications Environmental MODEL NAME: August ASL-01 DESCRIPTION: BLE Automatic Smart Lock MODEL NUMBER: ASL-01 STANDARDS: Bluetooth Specification v4.0 (BLE), 2.4GHz ISM band (2402MHz to 2480MHz), CHANNELS: 40 x 2.0MHz channels DATA RATE AND MODULATION: 1Mbps, GFSK, 250KHz deviation. INTERFACE: Bluetooth Smart Ready {BLE) LED: Lock/Unlock SPEAKER: Output, 1Watt Max. ANTENNA: Internal Single-band (lnternallFA) Transmitted RECEIVE SENSITIVITY: -84dBm Typical POWER CONSUMPTION: TX: BLE: 30mA Max.