Use and Care Manual

ManualsBrandsAupodin ManualsChest Of DrawersModern 3-Drawer Natural Oak Chest Dresser Mid Century Organizer Bedroom Furniture 31.5 in. W x 15.75 in. D x 29.53 in. H

1 HOUR

2 PEOPLE

2 x 1 m

H0037

3 Drawers Storage

Dresser Chest

Summary of content (12 pages)

PAGE 1
Contact Us: service@anmytek.
PAGE 2
H0037 Item No. : XXXX Contact Us : service@anmytek.com SAFETY PRECAUTIONS PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING AND USING THE PRODUCT. 1. Please check that all parts are present beforeyou start the assembly of your furniture. A Philips head screwdriver (not included) is required for the assembled of this product. 2. For ease and speed of assembly, we recommend that before you commence each step of the assembly, that you identify all the parts required for that step. 3.
PAGE 3
Item No. : XXXX H0037 Contact Us : service@anmytek.com PARTS LIST 3.5x30mm Ax25 Bx27 Cx27 3.5x10mm Dx32 Gx3 Jx3 Mx1 Ex6 3.5x45mm Hx4 Kx12 Nx8 Fx3 Ix3 6x35mm Lx4 3x10mm Ox8 3.5x35mm Px2 3.5x10mm Sx2 Qx2 Rx2 3x12mm Tx12 Contact Us : service@anmytek.
PAGE 4
Item No. : H0037 Contact Us : service@anmytek.com ASSEMBLY DIAGRAM ⑪ ⑫ ⑦ ⑨ ⑩ ⑫ ⑨ ⑧ ⑬ ⑮ ⑭ ⑥ ② ① ⑮ ⑭ ⑤ ④ ③ AFTER SALES SUPPORT If you have any general enquiries or require spare parts for this product, please feel free to contact us via the following email: Email: service@anmytek.com You can contact us for support at any time. We'll answer you in 24hrs. Contact Us : service@anmytek.
PAGE 5
TIPS Before ASSEMBLY IMPORTANT: 1. Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes. 2. Do not over tighten screws and bolts to avoid stripping. What you need • • Some of your favourite fruits or your preferred snacks. Use the packaging carton as a working surface to prevent possible product damage during assembly.
PAGE 6
Item No. : XXXX H0037 Contact Us : service@anmytek.com ASSEMBLY STEPS STEP 1. ④ ③ ② B C ① Attach part (2), (3), (4) to part (1) using 5 x cam bolts (C) and 5 x cam locks (B). Tighten with a screwdriver. STEP 2. A A ⑥ ⑤ x3 Slide panel (5) into position as shown. Attach part (6) to assembled unit using 5 x screws (A). Tighten with a screwdriver. Contact Us : service@anmytek.
PAGE 7
H0037 Item No. : XXXX Contact Us : service@anmytek.com ASSEMBLY STEPS STEP 3. T E ① x3 Attach 2 x handles (E) to the drawer using 4 x screws (T). Tighten with a screwdriver. G STEP 4. F D x3 D Attach rail (F) to the left side of drawer as shown and secure with 2 x screws (D). Attach rail (G) to the right side of drawer as shown and secure with 2 x screws (D). Tighten with a screwdriver. Contact Us : service@anmytek.
PAGE 8
H0037 Item No. : XXXX Contact Us : service@anmytek.com ASSEMBLY STEPS STEP 5. ⑧ ⑦ J I D D Find out the correct runners (I) and (J). Fix (I) on panel (7), (J) on panel (8) using 12 x screws (D). Don't mix (I) and (J). For the 6 x runners (I & J), the protruding edge at the silver button screw end is upward. The end of the runners (I) and (J) are close to the seam. STEP 6.
PAGE 9
Item No. : XXXX H0037 Contact Us : service@anmytek.com ASSEMBLY STEPS C K STEP 7. B ⑧ C B Attach the right side panel (8) to the assembled unit using 2 x wooden dowels (K), 4 x cam bolts (C) and 4 x cam locks (B) as shown. Tighten with a screwdriver. STEP 8. ⑪ C B ⑫ Slide back panel (12) into position. Attach the top panel (11) to assembled unit using 4 x wooden dowels (K), 4 x cam bolts (C) and 4 x cam locks (B). Tighten with a screwdriver. Contact Us : service@anmytek.
PAGE 10
Item No. : XXXX H0037 Contact Us : service@anmytek.com ASSEMBLY STEPS H STEP 9. ⑬ ⑫ Turn the furniture upside down. Attach the bottom panel (13) to assembled unit using 4 x wooden dowels (K) and 4 x screws (H). Tighten with a screwdriver. STEP 10. ⑮ A ⑭ ⑭ ⑮ L M Attach 2 x parts (14) to 2 x parts (15) using 4 x bolts (L). Tighten with a hex key (M). Attach the metal frame to the bottom panel using 10 x screws (A). Contact Us : service@anmytek.
PAGE 11
Item No. : H0037 Contact Us : service@anmytek.com ASSEMBLY STEPS STEP 11. N Attach 8 x plastic wedges (N) to the back panels using 8 x screws (O). Tighten with a screwdriver. STEP 12. R Q S Attach 2 x safety straps (Q) to the back panel of furniture using 2 x screws (S) as shown. Fasten assembled furniture to the wall using 2 x wall anchors (P), 2 x screws (R). Ensure unit is balanced and steady before use. Contact Us : service@anmytek.
PAGE 12
H0037 Item No. : XXXX Contact Us : service@anmytek.com WALL FIXING GUIDE NOTE: Supplied wall plugs are only suitable for use in masonry walls. If you have any doubts about using the correct plug for your wall, please seek professional advice. Failure of the product due to using incorrect ﬁxings is the responsibility of the installer. IMPORTANT: When drilling into walls, always check for hidden wires or pipes, etc. Tips & Tricks Make sure that the hardware used is suitable for supporting your unit.