User Manual

ManualsBrandsAuray ManualsBoompole AccessoriesCable Replacement Kit for CFP-68 Series Boom Poles

Cable Replacement Kit

CFC Series

Owner’s Manual

for CFP Series Carbon Fiber Boom Poles

Introduction

Thank you for choosing Auray.

The Auray CFC replacement kit provides a

replacement cable for the Auray CFP carbon ﬁber

boom pole. Auray’s solderless design provides a

fast and easy solution for cable replacement.

The high-quality coiled cable features a right-angle

XLR connector manufactured by Neutrik®, and a

TA3 (mini XLR) connector manufactured by Rean®

(a registered trademark of Neutrik®) for secure

locking connections and ﬂawless signal transfer.

This cable also features Auray’s unique strain relief

system that absorbs tension and protects the cable

from damage at the edge of the tip exit and at the

T3 connector. The included hex key and a small

slotted screwdriver (not included) are the only tools

needed for this cable replacement procedure that

will assure long-lasting and trouble-free operation

of your CFP boom pole.

Right-angle

XLR connector

TA3 (mini XLR)

connector

Coiled XLR

cable

Tip strain relief

Nylon line

1.5 mm hex

key

This Auray product is warranted to the original purchaser

to be free from defects in materials and workmanship

under normal consumer use for a period of one (1) year

from the original purchase date or thirty (30) days after

replacement, whichever occurs later. The warranty

provider’s responsibility with respect to this limited

warranty shall be limited solely to repair or replacement,

at the provider’s discretion, of any product that fails

during normal use of this product in its intended manner

and in its intended environment. Inoperability of the

product or part(s) shall be determined by the warranty

provider. If the product has been discontinued, the

warranty provider reserves the right to replace it with a

model of equivalent quality and function.

This warranty does not cover damage or defect caused

by misuse, neglect, accident, alteration, abuse, improper

installation or maintenance. EXCEPT AS PROVIDED

HEREIN, THE WARRANTY PROVIDER MAKES NEITHER

ANY EXPRESS WARRANTIES NOR ANY IMPLIED

WARRANTIES, INCLUDING BUT NOT LIMITED TO

ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. This warranty

provides you with speciﬁc legal rights, and you may also

have additional rights that vary from state to state.

To obtain warranty coverage, contact the Auray Customer

Service Department to obtain a return merchandise

authorization (“RMA”) number, and return the defective

product to Auray along with the RMA number and proof

of purchase. Shipment of the defective product is at the

purchaser’s own risk and expense.

For more information or to arrange service, visit

www.aurayaudio.com or call Customer Service at

212-594-2353.

Product warranty provided by the Gradus Group.

www.gradusgroup.com

Auray is a registered trademark of the

One-Year Limited Warranty

GG2

Warnings

• Please read and follow these instructions,

and keep this manual in a safe place.

• Handle the product with care.

• Use only parts provided by the manufacturer.

• Make sure the item is intact and

that there are no missing parts.

• Do not attempt to disassemble or

repair the equipment—doing so will

void the warranty, and Auray will not

be responsible for any damage.

• All photos are for illustrative purposes.

Install the replacement cable

1. Holding the boom

pole upright, insert

the replacement

cable into the top of

the boom pole,

and snake it through

the tubing until

the TA3 connector

is exposed at the

bottom of the pole.

Note: If the cable

does not move

smoothly through

the tubing, use the

included nylon line.

Tie the string to the

TA3 connector,

and drop it through

the tubing from the

top. Pull the line from

the bottom of the

boom pole to snake

the cable through the

tubing. Make sure

to remove the line

before continuing.

2. Fit the narrow side of

the strain relief over

the TA3 connector,

and push it past the

TA3 connector’s

locking tab.

3. Plug the TA3

connector into

the side-exit XLR

housing by inserting

it into the TA3 mount

and pushing in until

it clicks.

Note: When properly

aligned, the TA3

connector will easily

slide into place. Do

not try to force the

connector into the

mount. Doing so could damage the connector

or the mount.

4. Push the strain relief all the way into the

side exit housing so it sits over the TA3

connector.

5. Screw the side exit housing onto the end of

the boom pole.

6. Place the strain relief of the cable into the tip

exit slot.

7. Replace the tip by screwing it in, and secure it

by tightening the set screw with the hex key.

Print on Matte Material

Folding Diagram

Place the

manual in

bag behind

the product

Summary of content (6 pages)

PAGE 1
CFC Series Cable Replacement Kit for CFP Series Carbon Fiber Boom Poles Owner’s Manual TA3 (mini XLR) connector Right-angle XLR connector Nylon line Coiled XLR cable 1.5 mm hex key Tip strain relief Introduction Thank you for choosing Auray. The Auray CFC replacement kit provides a replacement cable for the Auray CFP carbon fiber boom pole. Auray’s solderless design provides a fast and easy solution for cable replacement.
PAGE 2
Instructions Replacing the Cable – Boom Pole with Bottom Exit XLR Remove the old cable 1. Use the hex key to loosen the set screw on the tip. 1 2. Remove the tip by unscrewing it. 2 3. Lift the cable and strain relief out of the tip exit slot. 3 Tip: Before proceeding, push a small length of cable into the tube from the tip of the pole. This will give you enough slack to complete the following steps. 4. Unscrew the bottom housing from the base of the boom pole. 4 5.
PAGE 3
Install the replacement cable 1. Holding the boom pole upright, insert the replacement cable into the top of the boom pole, 1 and snake it through the tubing until the TA3 connector is exposed at the 1 2 bottom of the pole. 2 Note: If the cable does not move smoothly through the tubing, use the included nylon line: tie the line to the TA3 connector and drop it through the tubing from the top. 3 Pull the string from the bottom of the boom pole to snake the cable through the tubing.
PAGE 4
Replacing the Cable – Boom Pole with Side Exit XLR Remove the old cable 1. Use the hex key to loosen the set screw on the tip. 1 2. Remove the tip by unscrewing it. 2 3. Lift the cable and strain relief out of the tip exit slot. 3 Tip: Before proceeding, push a small length of cable into the tube from the tip of the pole. This will give you enough slack to complete the following steps. 4.
PAGE 5
Install the replacement cable 1. Holding the boom pole upright, insert the replacement cable into the top of the boom pole, 1 and snake it through the tubing until the TA3 connector is exposed at the 1 2 bottom of the pole. 2 Note: If the cable does not move smoothly through the tubing, use the included nylon line. Tie the string to the TA3 connector, 3 and drop it through the tubing from the top. Pull the line from the bottom of the boom pole to snake the cable through the tubing.
PAGE 6
Warnings ! • Please read and follow these instructions, and keep this manual in a safe place. • Handle the product with care. • Use only parts provided by the manufacturer. • Make sure the item is intact and that there are no missing parts. • Do not attempt to disassemble or repair the equipment—doing so will void the warranty, and Auray will not be responsible for any damage. • All photos are for illustrative purposes.