March 09 Domestic Cold Water High Pressure Cleaner Instruction Manual Aussie Eco-Clean Concept F140 Please read this manual before using the machine.
Let’s Clean up Australia with an Aussie Eco-Clean Concept F140 Congratulations on your acquisition of a top quality Aussie Concept F140 2,000 psi high pressure water blaster. This machine offers users a wide range of features that make cleaning tasks a breeze. Pump The axial piston pump is the heart of the machine, and features a brass head and stainless steel pistons.
WARRANTY WARRANTY LIMITATIONS ON DOMESTIC MACHINES: The Aussie Concept F140 is guaranteed for 12 months from original date for purchase. Australian Pump Industries warrants that the pressure cleaner will be free of defects in workmanship or material. Domestic machines (i.e. Concept F140) which are used in commercial service are warranted for a period of three months from date of purchase.
SAFETY PRECAUTIONS - IMPORTANT WARNING It is important that you read, fully understand and observe ALL of the following safety precautions and warnings. Careless or improper use of any high pressure cleaner may cause serious or even fatal injury. 1. Minors should never be allowed to operate this machine. 2. Never direct spray jet at any material that may contain asbestos. 3. Keep area where machine is in use clear of any bystanders or animals. 4. Never let this machine run unattended. 5.
Safety Precautions cont. 22. Always keep electrical connections dry and off the ground. 23. Do not touch plug with wet hands. 24. To avoid damage to cable do not roll, crush or pull it. 25. Always inspect the power cable before and after use for any signs of damage or aging. 26. Always hold spray gun and lance firmly with both hands so you maintain full control. 27. Do not operate the machine whilst standing on ladders. Use scaffolding or a platform tower. Always keep good footing and balance.
TECHNICAL SPECIFICATIONS Working pressure Maximum water flow Supply voltage Power consumption Weight Pump head Maximum water temperature Maximum inlet pressure Minimum water pressure requirement Detergent tank capacity Total Stop Noise Level F140 2000psi 9 lit/min 240v 10amp 2.2 kW 29 kg brass 50ºC 50psi 28psi 5 litres Yes 76 dBA PRODUCT INFORMATION Concept F-140 1 2 8 5 7 9 6 3 1. 2. 3. 4. 5. 6. 7. 8. 9.
ASSEMBLY/PREPARATION & USE WARNING: When the machine is new it requires a brief running in of motor/pump unit. Running in consists of running the machine for no longer than one hour and letting it cool for at least one hour. This operation should be repeated at least three or four times. Step 1: - Remove plastic travel caps from both inlet and outlet (if supplied). Fit inlet and outlet hoses as described below. Step 2: - Connect water hose (garden hose). (Ensure fittings are clean.
START UP PROCEDURE BLEEDING PUMP - Turn water supply on (accessories must be assembled as described above) - Bleeding of pump requires the operator to have the high pressure gun trigger pulled while the machine is turned off. - When the trigger is pulled and the water supply is turned on, this should give a constant water supply coming through the machine while it is turned off. - Only switch machine on after water supply is turned on and the operator has bled water through the pump.
DETERGENT APPLICATOR (CLEANING AGENTS) Step 1: - Fill detergent tank with detergent: The Concept F140 detergent tank is incorporated into the chassis of the machine. When filling the detergent tank never pour detergent into the tank unless it has been diluted down. If the detergent is too thick, this will cause blockage through the detergent injector (Fig. 7).
CARE AND MAINTENANCE WARNING: Ensure the plug is removed from socket before carrying out any maintenance, adjustment or servicing. 1. Storage: Store your Aussie-Eco Clean blaster in an upright position. If there is a danger of freezing have your local authorised Aussie Pumps Service Agent inspect unit before next operation. 2. Long Storage: If you plan to store your machine for a long period it is recommended that you run antifreeze through the machine before storage.
SPARE PARTS Commonly used parts: Valve kit FKTRI64672 Minor seal kit FKTRI64746 Major seal kit FKTRI64832 Manifold kit (Kit E) FKTRI83733 T10 vario zoom nozzle & lance C4723.45.115 Aussie Turbo master turbo lance CTN140-035 Gun C4333.
TROUBLESHOOTING Before starting any work on the machine unplug the power cable, turn off the water supply and activate the spray gun until the pressure has been relieved completely.