INSTALLATION AND OPERATION MANUAL AMC+ SERIES MIXER AMPLIFIERS AMC+30 AMC+60 AMC+120 AMC+250
IMPORTANT SAFETY INFORMATION PRÉCAUTIONS DURANT UTILISATION 1. Read these instructions. 1. LISEZ ces instructions. 2. Keep these instructions. 2. Tenez ces instructions. 3. Heed all warnings. 3. Notez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les avertissements. 5. Do not use this apparatus near water. 5. N’utilisez pas ce produit près de l’eau (la piscine, la plage, le lac, etc.). 6. Clean only with dry cloth. 6. Nettoyez seulement avec une étoffe sèche.
INTRODUCTION AND CONTENTS AMC+ SERIES INTRODUCTION 3 The Australian Monitor AMC+ series of amplifiers takes the heritage and reliability of our famous AMIS series amplifiers and integrates these features into low cost amplifiers for applications where reliability is everything, but the more elaborate features of our AMIS series are not required.
FRONT PANEL 1 2 3 4 5 6 1 CH 1–4 These control the levels for each channel input. 2 Bass There is 12dB of cut and boost at 100Hz. 3 Treble There is 9dB of cut and boost at 10kHz. 4 Master This controls the overall mixed output level. 5 On This LED indicates the unit is powered “on”. 6 Power This switch switches power on or off the mains. The up position is on. NOTE: For the model AMC+30 Risk of hazardous energy. Class 2 wiring should be used.
REAR PANEL This terminal is hazardous live and that external wiring connected to these terminals requires installation by an instructed person. C DIRECT OUT CLASS 2 WIRING OHM LINE 4 100 70 C COM TONE MODULE 1 2 3 4 AMC+ 120 Audio Amplifier Model: AMC+120 Rated Value: 115V~60Hz 460W 230V~ 50Hz 460W Manufacture Date: Made In China CONFORMS TO ANSI/UL SYD.60065 CERTIFIED TO CAN/CSA STD.C22.2 No.60065 115 V. FUSE T4AH 250V 230 V.
INSTALLATION NOTE: Only connect one output – either Distributed Line or Low Impedance Mounting Your amplifier is designed for standard 19” rack mounting and occupies 2 EIA rackunits (3.5”). The mounting centres are: Vertical: 3.0” (76.2mm) Horizontal: 18.2” (461.2mm) to 18.7” (473.8mm) The slots in the mounting flange will accept bolt diameters up to 1/4” (6.35mm).
INSTALLATION Direct Output The output terminal strip accepts wire sizes from 16-22AWG (1.5mm2 – 0.35mm2) or spade lugs. The following table should be used as a guideline for cable sizes. Regulations in your area may require different gauged wire and should be checked before using. OUTPUT DISTANCE WIRE SIZE AMC+30 100V 70V 4 ohm AMC+60 AMC+120 AMC+250 Up to 50m AWG26(0.12mm2) AWG26(0.12mm2) AWG24(0.2mm2) AWG22(0.35mm2) 50m–200m AWG24(0.2mm2) AWG20(0.5mm2) AWG18(0.75mm2) AWG16(1.
TROUBLESHOOTING TROUBLESHOOTING GUIDE Trouble Likely Cause Remedy Power LED not on Power not reaching amplifier Check power switch is on Check mains connection Check mains fuse Distorted sound Output is short circuit Check speaker loads for shorts Input is overloaded Reduce input level at source Output is being over driven Reduce volume levels on front panel Bass control is turned up Reduce Bass control level Volume controls down Check volume controls Amplifier has overheated (AMC+60, AMC+
BLOCK DIAGRAM AMC+ SERIES INSTALLATION AND OPERATION MANUAL PAGE 9
FUNCTIONAL NOTES AND INTERNAL ADJUSTMENTS Priority Channel 1 will mute channels 2, 3 and 4. This will only occur when signal appears on channel 1, irrespective of the channel volume control. Priority can be disabled. (See below). The release time is approx. 3 secs and is NOT adjustable. The mute depth is approx. 40dB and is not adjustable. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING ! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
DIMENSIONS C DIRECT OUT CLASS 2 WIRING OHM LINE 4 100 70 C COM TONE MODULE 1 2 3 4 AMC+ 120 Audio Amplifier Model: AMC+120 Rated Value: 115V~60Hz 460W 230V~ 50Hz 460W Manufacture Date: Made In China CONFORMS TO ANSI/UL SYD.60065 CERTIFIED TO CAN/CSA STD.C22.2 No.60065 115 V. FUSE T4AH 250V 230 V.
SPECIFICATIONS AMC+ 30 AMC+ 60 AMC+ 120 AMC+ 250 30W 60W 120W 250W > 75dBr > 75dBr > 80dBr >85dBr 85Hz-18kHz 75Hz-20kHz 70Hz-20kHz 40Hz-20kHz 1.0A 0.5A 1.6A (x2) 3.15A 1.6A 4A 4A 2A 8A 8A 4A 10A (x2) 96% 93% 93% 90% 482 x 88 x 190mm 19” x 3.5” x 7.5” 482 x 88 x 281mm 19” x 3.5” x 11.1” 482 x 88 x 281mm 19” x 3.5” x 11.1” 482 x 88 x 384mm 19” x 3.5” 15.1” Net Weight 6.7kg 14.7lb 7.8kg 17.1lb 9.2kg 20.3lb 11.5kg 25.3lb Shipping Weight 8.7kg 19.2lb 9.8kg 21.
SPECIFICATIONS COMMON TO ALL MODELS Thd (1khz, -1db) Better than 0.5% Mic Input SENSITIVITY IMPEDANCE HEADROOM 1mV @ 200ohm 1k3 ohm 77mV (37dB) Aux Input SENSITIVITY IMPEDANCE HEADROOM 150mV >200kohm > 15V (>40dB) Tone Control BASS @ 100HZ TREBLE @ 10KHZ +/- 12 dB +/- 9 dB Line Out NOMINAL OUTPUT OUTPUT IMPEDANCE 0.
NOTES PAGE 14 AMC+ SERIES INSTALLATION AND OPERATION MANUAL
NOTES AMC+ SERIES INSTALLATION AND OPERATION MANUAL PAGE 15
ENGINEERED BY AUSTRALIAN MONITOR Address: 1 Clyde Street, Silverwater, Sydney NSW 2128 Australia. Private Bag 149, Silverwater NSW 1811 ABN 78 001 345 482 Website: www.australianmonitor.com.au International enquiries email: international@australianmonitor.com.au DISTRIBUTED IN AUSTRALIA AND NEW ZEALAND BY HILLS SVL www.hillssvl.com.au NSW P: 02 9647 1411 E: nsw@hillssvl.com.au QLD P: 07 3852 1312 E: qld@hillssvl.com.au ACT P: 02 6260 4544 E: act@hillssvl.com.au WA P: 08 9204 0200 E: wa@hillssvl.com.
