INSTALLATION AND OPERATION MANUAL AMD SERIES POWER AMPLIFIER AMD2200P
IMPORTANT SAFETY INFORMATION PRÉCAUTIONS DURANT UTILISATION 1. Read these instructions. 1. LISEZ ces instructions. 2. Keep these instructions. 2. Tenez ces instructions. 3. Heed all warnings. 3. Notez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les avertissements. 5. Do not use this apparatus near water. 5. N’utilisez pas ce produit près de l’eau (la piscine, la plage, le lac, etc.). 6. Clean only with dry cloth. 6. Nettoyez seulement avec une étoffe sèche.
INTRODUCTION AND CONTENTS AMD2200P The AMD P series of power amplifiers from Australian Monitor represent a quantum leap forward in connectivity, controllability & flexibility in the constant voltage amplifier market. The AMD series allows a contractor to integrate the power amplifier to a third party control system for remote audio control or simply use the AMD amplifiers as standard power amplifiers. Australian Monitor AMD P series is the future of constant voltage amplification.
FRONT PANEL 1 2 3 4 1 Signal Indicator The signal indicator will go blue when audio is present on that channel of the amplifier. 2 Fault Indicator The fault indicator will go red when a fault is present on that channel of the amplifer. 3 Clip Indicator The clip indicator will go red when an audio input is reaching the clipping stage. If this is happening the input should reduced using the input attenuator at the rear of the unit, or at the program source.
REAR PANEL 1 2 1 230 to 240V or 115V to 120V The power input is NOT auto-switching. Australian Monitor should be contacted if the voltage needs to be changed from its shipped configuration. The power input also features a power switch, this is a hard power off and will shut down the unit completely. 2 Amp Outputs: The output for each channel can be either 100V Line, 70V Line or 4 Ohm low impedence. Only one output type should be used at once.
INSTALLATION Unpacking Cooling Every Australian Monitor product is tested and inspected before leaving our factory and should arrive in perfect condition. The AMD2200P amplifier utilises fan forced air cooling, with air flowing from right to left (viewed from the front). When opening the carton check for any noticeable damage to your Australian Monitor product. Please notify your Australian Monitor reseller immediately should any damage be discovered.
RS232 PROTOCOL Port & Protocol Information Channel Input Cross Mix Level: The RS232 port of the AMD2200P amplifier’s consists of three connections: To adjust the volume control of an input cross mix level. Transmit – Data from the amplifier Receive – Data into the amplifier GND – Ground connection NOTE: there are no flow control connections The baud rate of the port is 19200 and the data format is 8 bits, no parity and 1 stop bit (8N1).
RS232 PROTOCOL Channel Output Level: Low Power Mode To adjust the volume control of an output channel. To place the enable or disable “low power mode” %PLVL:xyy In this command x represents the output channel to select (between 1 and 4). The volume is represented by the yy section of the command. yy can range between 00 (off) and E1 (225 = +12dB of gain).
COMMAND SUMMARY Description Command Response Notes Get input cross-mix level %PCML:xy?? %PCML=xyzz x ranges from 01 to 04 y ranges from 01 to 04 zz ranges from 00 to E1 Get input cross-mix mute %PCMM:xy?? %PCMM=xyzz x ranges from 01 to 04 y ranges from 01 to 04 zz ranges from 00 to 01 Set input cross-mix level %PCML:xyzz %PCML=xyzz x ranges from 01 to 04 y ranges from 01 to 04 zz ranges from 00 to E1 Set input cross-mix mute %PCMM:xyzz %PCMM=xyz
482.00 mm (19.0”) 465.00 mm (18.3”) 44.00 mm (1.75”) 32.00 mm (1.25”) DIMENSIONS 430.00 mm (16.9”) 438.00 mm (17.
SPECIFICATIONS Frequency Response Total Harmonic Distortion Input Impedance Specification Conditions 70 Hz - 18 kHz, -3 dB Signal Input 2 dB below clip < 0.
ENGINEERED BY AUSTRALIAN MONITOR Address: 1 Clyde Street, Silverwater, Sydney NSW 2128 Australia. Private Bag 149, Silverwater NSW 1811 ABN 78 001 345 482 Website: www.australianmonitor.com.au International enquiries email: international@australianmonitor.com.au DISTRIBUTED IN AUSTRALIA AND NEW ZEALAND BY HILLS SVL www.hillssvl.com.au NSW P: 02 9647 1411 E: nsw@hillssvl.com.au QLD P: 07 3852 1312 E: qld@hillssvl.com.au ACT P: 02 6260 4544 E: act@hillssvl.com.au WA P: 08 9204 0200 E: wa@hillssvl.com.
