INSTALLATION AND OPERATION MANUAL AMPAV40 ACTIVE THREE WAY STEREO SPEAKER SYSTEM
IMPORTANT SAFETY INFORMATION PRÉCAUTIONS DURANT UTILISATION 1. Read these instructions. 1. Lisez ces instructions. 2. Keep these instructions. 2. Tenez ces instructions. 3. Heed all warnings. 3. Notez tous les avertissements. 4. Follow all instructions. 4. Suivez toutes les avertissements. 5. Do not use this apparatus near water. 5. N’utilisez pas ce produit près de l’eau (la piscine, la plage, le lac, etc.). 6. Clean only with dry cloth. 6. Nettoyez seulement avec une étoffe sèche.
INTRODUCTION AND CONTENTS AMPAV40 INTRODUCTION 3 The Australian Monitor AMPAV40 is an active three-way stereo speaker system consisting of one powered and one passive speaker. The speakers are compact, architecturally pleasing and come supplied with adjustable mounting brackets. Features include an on-board 20 W stereo amplifier, Treble, Bass and Volume controls, unbalanced stereo RCA inputs and balanced stereo line inputs as well as remote control operation and USB support.
AMPAV40 FRONT PANEL – ACTIVE AND PASSIVE Grill removed 3 4 2 1 1 5.25” BASS DRIVER 2 0.5” DYNAMIC TWEETER 3 1.
AMPAV40 REAR PANEL – ACTIVE Active 9 7 8 5 6 3 4 2 1 10 The AMPAV40 has a number of functions and input options which may be selected from the active speaker’s rear panel or from the supplied remote control. 1 CONTROL Power: A power LED indicator on the control panel segment indicates when power is on (red) or when the system is in standby (orange). 4 USB Input connection port for a USB memory stick. Be sure to switch the INPUT to USB, a red LED indicates when USB has been selected.
AMPAV40 REAR PANEL – ACTIVE (continued) & PASSIVE Passive 12 7 SPEAKER OUTPUT 4 Ω Connection to the passive 4 Ohm external speaker is provided through a two pin terminal socket and comes fitted with removable screw terminal plug. The passive speaker becomes the right hand channel whilst the left channel is the active speaker. Connect the supplied figure 8 or a similar speaker cable between the active and passive speaker.
REMOTE 1 2 3 4 5 6 The AMPAV40 speaker is turned on from the mains switch at the rear of the unit. Once activated, the remote control can then be used to operate the speaker remotely including setting the speaker system to standby mode when not in use. 1 ON This command will turn the unit on when in standby mode. The power LED will change from orange to red. 2 ST.BY Pressing ST.BY places the speaker system into standby mode. The indicator LED turns orange.
MOUNTING MOUNTING When mounting AMPAV speakers the following safety issues must be considered; The mounting of a permanently installed speaker may be dangerous unless undertaken by a qualified professional with relevant experience. Walls and mounting surfaces must be capable of supporting the speaker and bracket in a safe and secure manner. All fixings must be safely attached to the speaker cabinet and the mounting surface.
DIMENSIONS 210 mm 240 mm 178 mm 193 mm AMPAV40 INSTALLATION AND OPERATION MANUAL PAGE 9
NOTES PAGE 10 AMPAV40 INSTALLATION AND OPERATION MANUAL
SPECIFICATIONS SPECIFICATIONS AMPAV40 Speaker system 3-Way Active Speaker 3-Way Passive Speaker Power (Continuous) 2 x 20 Watts Impedance 4 Ohms Sensitivity (1 W / 1 M) 88 dB Calculated max SPL (per speaker) 101 dB Frequency Response (-3 dB) 45 Hz – 20 kHz Frequency Response (-10 dB) 40 Hz – 22 kHz Speaker Components Woofer 134 mm (5.25”) Polypropylene 25 mm (1”) Piezo Tweeter 12.5 mm (0.
ENGINEERED BY AUSTRALIAN MONITOR Address: 1 Clyde Street, Silverwater, Sydney NSW 2128 Australia. Private Bag 149, Silverwater NSW 1811 ACN 007 573 417 Website: www.australianmonitor.com.au International enquiries email: international@australianmonitor.com.au DISTRIBUTED IN AUSTRALIA AND NEW ZEALAND BY HILLS SVL www.hillssvl.com.au NSW P: 02 9647 1411 E: nsw@hillssvl.com.au QLD P: 07 3852 1312 E: qld@hillssvl.com.au ACT P: 02 6260 4544 E: act@hillssvl.com.au WA P: 08 9204 0200 E: wa@hillssvl.com.