User Manual
Table Of Contents
- Trademarks
 - Copyright Information
 - Disclaimer of Warranties and Limitation of Liabilities
 - For Services and Support:
 - Safety Information
 - Contents
 - Chapter 1 Using This Manual
 - Chapter 2 General Introduction
 - Chapter 3 Getting Started
 - Chapter 4 Diagnostics Operations
 - Chapter 5 Data Manager Operations
 - Chapter 6 MaxiFix Operations
- 6.1 Navigation
- The Header
 - Select Vehicle Button
 - The “Select Vehicle” button on the Header allows you to specify the vehicle which you want to reference on MaxiFix, by selecting each of the vehicle attribute from a sequence of option lists. This feature helps to filter out the searches that allow on...
 - 6.1.1 Terminology
 
 - 6.2 Operations
 
 - 6.1 Navigation
 - Chapter 7 Settings Operations
 - Chapter 8 Shop Manager Operations
 - Chapter 9 Update Operations
 - Chapter 10 VCI Manager Operations
 - Chapter 11 Remote Desk Operations
 - Chapter 12 Support Operations
 - Chapter 13 Training Operations
 - Chapter 14 Quick Link Operations
 - Chapter 15 MaxiScope Operations
- 15.1 Safety Information
 - 15.2 Glossary
 - 15.3 MaxiScope Module
 - 15.4 Screen Layout and Operations
- 15.4.1 Top Toolbar
- Math Channel
 - A math channel is virtual channel generated by mathematical function of the input channel. It can be displayed in a scope or XY view in the same way as an input signal, and like an input signal it has its own measure axis, scaling and color. The MaxiS...
 - Probe
 - A probe is any transducer, measuring device or other accessory that you connect to an input channel of your MaxiScope module.
 - Reference Waveform
 - Recall Reference
 
 - 15.4.2 Functional Buttons
 - 15.4.3 Measurement Grid
 - 15.4.4 Measurement Rulers
 - 15.4.5 Functional Buttons
 
 - 15.4.1 Top Toolbar
 - 15.5 Troubleshooting
 - 15.6 MaxiScope Firmware Update
 
 - Chapter 16 Digital Inspection Operations
 - Chapter 17 Maintenance and Service
 - Chapter 18 Compliance Information
 - Chapter 19 Warranty
 
MaxiFix Operations      Operations 
72 
View Profile Information 
You  can  view  your  personal  profile  by  clicking  on  your  account  ID  or  “My 
Profile” in My MaxiFix section or edit portrait where applicable, and visit other 
community members’  profile  by clicking their portrait. Information included in 
your profile determines how you are presented to the community, and what 
type of information will be sent to you from the community. 
6.2.5  My Messages 
My Messages, the fifth option on the Navigation Menu  at the  bottom of the 
screen, shows a list of message notification which is relevant to your activities 
in the Question section. A notification icon will appear on the top-right corner of 
“My Messages” if there is any new or unread message in the Question section. 
The number on the notification icon indicates the total number of the new and 
unread  messages.  The  displayed  number  will  be  reduced  correspondingly 
after  viewing.  The message  notification will appear  under the  following two 
conditions: 
1.  Your  question  or  answer  is  replied  by  other  MaxiFix  community 
members. 
2.  Your  answer  is  marked  as  the  “Adopted!”  by  the  MaxiFix  community 
member who asked the question. 
Tap My Messages, select and open the message you want to read from the list. 
If  your  problem  is  solved  according  to  the  reply,  you  should  select  one 
Adopted  Answer  and  close  the  question.  If  your  answer  is  marked  as 
“Adopted!”, the prompt “Adopted! + 4” will be displayed permanently. 
Tap Clear to delete all message notifications. 
Select “Adopted Answers” 
Members  are  requested  to  select  one  Adopted  Answer  from  all  of  the 
responses on “My Messages” page before closing a question. The community 
members  who  provided the  Adopted  Answer  are  rewarded  with  scores  for 
their contribution. 
About Adopted Answer: 
  Only one answer can be selected as “Adopted Answer”. 
  Answers  can  only  be  rated  by  the  MaxiFix  member  who  asked  the 
question. 










