User Manual

ManualsBrandsAutel ManualsAutomotiveMaxiSys Automotive Scan Tool, 2021 Newest Diagnostic Scanner Upgraded Ver. of MS906, with Advanced ECU Coding, Full Bi-Directional Control, 31 Services & OE-Level All Systems Diagnosis

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabilities
For Services and Support:
Safety Information
- Safety Messages
- Safety Instructions
Chapter 1 Using This Manual
- 1.1 Conventions
Chapter 2 General Introduction
- 2.1 MaxiSys System Display Tablet
- 2.2 VCI – Wireless Diagnostic Interface
- 2.3 Accessory Kit
  - 2.3.1 OBD I Adapters
  - 2.3.2 Other Accessories
Chapter 3 Getting Started
- 3.1 Powering Up
- 3.2 Powering Down
  - 3.2.1 Reboot System
- 3.3 Installing Computer Software
  - 3.3.1 Printing Operation
Chapter 4 Diagnostics Operations
- 4.1 Establishing Vehicle Communication
- 4.2 Getting Started
  - 4.2.1 Vehicle Menu Layout
    - Top toolbar Buttons
    - Manufacturer Buttons
- 4.3 Vehicle Identification
- 4.4 Navigation
- 4.5 Main Menu
- 4.6 Diagnosis
- 4.7 Service
  - 4.7.1 Function Descriptions
- 4.8 Generic OBD II Operations
  - 4.8.1 General Procedure
  - 4.8.2 Function Descriptions
- 4.9 Exiting Diagnostics
Chapter 5 TPMS Service Operations
- 5.1 Navigation
  - 5.1.1 TPMS Service Screen Layout
- 5.2 Check Operations
  - Main Section
- 5.3 Programming Operations
- 5.4 Relearn Operations
Chapter 6 MaxiFix Operations
- 6.1 Navigation
- 6.2 Operations
Chapter 7 Shop Manager Operations
- 7.1 Vehicle History
  - 7.1.1 Historical Test Record
- 7.2 Workshop Information
- 7.3 Customer Manager
  - 7.3.1 History Notes
Chapter 8 Data Manager Operations
- 8.1 Operations
Chapter 9 Settings Operations
- 9.1 Operations
Chapter 10 Update Operations
Chapter 11 VCI Manager Operations
- 11.1 BT Pairing
- 11.2 Update
- 11.3 TPMS Module Update
Chapter 12 Support Operations
- 12.1 Product Registration
- 12.2 Support Screen Layout
- 12.3 My Account
- 12.4 User Complaint
  - Screen Layout
- 12.5 Data Logging
- 12.6 Communities
  - User Profile
- 12.7 Training Channels
- 12.8 FAQ Database
Chapter 13 Training Operations
Chapter 14 Remote Desk Operations
- 14.1 Operations
Chapter 15 Quick Link Operations
Chapter 16 Oscilloscope Operations
- 16.1 Safety Information
- 16.2 Glossary
- 16.3 MaxiScope Module
  - Power Source
  - Technical Specifications
- 16.4 Screen Layout and Operations
- 16.5 Troubleshooting
- 16.6 MaxiScope Firmware Update
Chapter 17 Digital Inspection Operations
- 17.1 Additional Accessories
- 17.2 Operations
Chapter 18 Maintenance and Service
- 18.1 Maintenance Instructions
- 18.2 Troubleshooting Checklist
- 18.3 About Battery Usage
- 18.4 Service Procedures
Chapter 19 Compliance Information
- FCC Compliance
- FCC ID: WQ8MAXISYSMY906TS (for MaxiSys MS906TS)
- FCC ID: WQ8MAXISYSMY906BT (for MaxiSys MS906BT)
- SAR:
Chapter 20 Warranty
- 12-Month Limited Warranty
- This warranty does not apply to:

TPMS Service Operations Relearn Operations

Figure 5-8 Sample Relearn Function Main Screen

The OEM sensor information and specification, and relearn procedure

for each vehicle will display on the right side of the screen. Please read

the relearn procedure carefully before performing the relearn function.

 To perform TPMS Relearn function

1. Establish the communication with the test vehicle via the MaxiVCI V100.

Power on the Display Tablet.

2. Turn the ignition on but do not start the engine.

3. Tap Relearn tab on the screen and select the specific function to continue.

Details are explained in the following sections.

5.4.1 OBDII Relearn

This function allows writing the sensor IDs to the TPMS ECU without

performing other procedures.

NOTE: Make sure all sensors are checked before performing the OBDII

Relearn function.