User Manual

ManualsBrandsAutel ManualsAutomotive2021 Autel MaxiSys Pro MK908P Auto Diagnostic Scanner ,Same as MaxiSys Elite, Upgraded of MS906TS/MS906BT/MS908/MK908, with Programming, Coding, Active Test, 30+ Service, MV105 Video Inspection

111

112

113

114

115

116

117

118

119

120

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabilities
For Services and Support:
Safety Information
- Safety Messages
- Safety Instructions
Contents
Chapter 1 Using This Manual
- 1.1 Conventions
Chapter 2 General Introduction
- 2.1 MaxiSys Display Tablet
- 2.2 VCI – Wireless Diagnostic Interface
- 2.3 VCI – J2534 ECU Programming Device
- 2.4 Accessories Kit
Chapter 3 Getting Started
- 3.1 Powering Up
- 3.2 Powering Down
  - 3.2.1 Reboot System
- 3.3 Installing Computer Software
  - 3.3.1 Printing Operation
Chapter 4 Diagnostics Operations
- 4.1 Establishing Vehicle Communication
- 4.2 Getting Started
  - 4.2.1 Vehicle Menu Layout
    - Top toolbar Buttons
    - Manufacturer Buttons
- 4.3 Vehicle Identification
- 4.4 Navigation
- 4.5 Main Menu
- 4.6 Diagnosis
- 4.7 Service
  - 4.7.1 Function Descriptions
- 4.8 Programming and Coding
- 4.9 Generic OBD II Operations
  - 4.9.1 General Procedure
  - 4.9.2 Function Descriptions
- 4.10 Exiting Diagnostics
Chapter 5 Data Manager Operations
- 5.1 Operations
Chapter 6 MaxiFix Operations
- 6.1 Navigation
- 6.2 Operations
Chapter 7 Settings Operations
- 7.1 Operations
Chapter 8 Shop Manager Operations
- 8.1 Vehicle History
  - 8.1.1 Historical Test Record
- 8.2 Workshop Information
- 8.3 Customer Manager
  - 8.3.1 History Notes
Chapter 9 Update Operations
Chapter 10 VCI Manager Operations
- 10.1 BT Pairing
- 10.2 Update
Chapter 11 Remote Desk Operations
- 11.1 Operations
Chapter 12 Support Operations
- 12.1 Product Registration
- 12.2 Support Screen Layout
- 12.3 My Account
- 12.4 User Complaint
  - Screen Layout
- 12.5 Data Logging
- 12.6 Communities
  - User Profile
- 12.7 Training Channels
- 12.8 FAQ Database
Chapter 13 Training Operations
Chapter 14 Quick Link Operations
Chapter 15 MaxiScope Operations
- 15.1 Safety Information
- 15.2 Glossary
- 15.3 MaxiScope Module
- 15.4 Screen Layout and Operations
- 15.5 Troubleshooting
- 15.6 MaxiScope Firmware Update
Chapter 16 Digital Inspection Operations
- 16.1 Additional Accessories
- 16.2 Operations
Chapter 17 Maintenance and Service
- 17.1 Maintenance Instructions
- 17.2 Troubleshooting Checklist
- 17.3 About Battery Usage
- 17.4 Service Procedures
Chapter 18 Compliance Information
- FCC Compliance FCC ID: WQ8MAXISYSMY908
- SAR:
Chapter 19 Warranty
- 12-Month Limited Warranty
- This warranty does not apply to:

MaxiScope Operations MaxiScope Module

109

Frequency

This term describes the number of signal occurrences per second. Frequency is

measured in Hz (hertz).

Square Waveform

This term describes the waveform characteristics normally generated by signals

switching between clearly defined voltage levels, such as a Hal effect sensor signal

may create by switching a voltage to ground. A typical digital square waveform is shown

below:

Figure 15-2 Sample Square Waveform

Peak to peak voltage

This term indicates the difference in voltage between the minimum and maximum

voltages occurring in the waveform.

15.3 MaxiScope Module

The MaxiScope Automotive Oscilloscope tool kit is optional and available for

purchase along with the MaxiSys package. There are 2 versions (basic and

advanced versions) available.

The MaxiScope tool kit comes standard with:

 MaxiScope Module

 CD with user manual and PC software