User Manual

ManualsBrandsAutel ManualsAutomotive2021 Autel MaxiSys Pro MK908P Auto Diagnostic Scanner ,Same as MaxiSys Elite, Upgraded of MS906TS/MS906BT/MS908/MK908, with Programming, Coding, Active Test, 30+ Service, MV105 Video Inspection

Table Of Contents

Trademarks
Copyright Information
Disclaimer of Warranties and Limitation of Liabilities
For Services and Support:
Safety Information
- Safety Messages
- Safety Instructions
Contents
Chapter 1 Using This Manual
- 1.1 Conventions
Chapter 2 General Introduction
- 2.1 MaxiSys Display Tablet
- 2.2 VCI – Wireless Diagnostic Interface
- 2.3 VCI – J2534 ECU Programming Device
- 2.4 Accessories Kit
Chapter 3 Getting Started
- 3.1 Powering Up
- 3.2 Powering Down
  - 3.2.1 Reboot System
- 3.3 Installing Computer Software
  - 3.3.1 Printing Operation
Chapter 4 Diagnostics Operations
- 4.1 Establishing Vehicle Communication
- 4.2 Getting Started
  - 4.2.1 Vehicle Menu Layout
    - Top toolbar Buttons
    - Manufacturer Buttons
- 4.3 Vehicle Identification
- 4.4 Navigation
- 4.5 Main Menu
- 4.6 Diagnosis
- 4.7 Service
  - 4.7.1 Function Descriptions
- 4.8 Programming and Coding
- 4.9 Generic OBD II Operations
  - 4.9.1 General Procedure
  - 4.9.2 Function Descriptions
- 4.10 Exiting Diagnostics
Chapter 5 Data Manager Operations
- 5.1 Operations
Chapter 6 MaxiFix Operations
- 6.1 Navigation
- 6.2 Operations
Chapter 7 Settings Operations
- 7.1 Operations
Chapter 8 Shop Manager Operations
- 8.1 Vehicle History
  - 8.1.1 Historical Test Record
- 8.2 Workshop Information
- 8.3 Customer Manager
  - 8.3.1 History Notes
Chapter 9 Update Operations
Chapter 10 VCI Manager Operations
- 10.1 BT Pairing
- 10.2 Update
Chapter 11 Remote Desk Operations
- 11.1 Operations
Chapter 12 Support Operations
- 12.1 Product Registration
- 12.2 Support Screen Layout
- 12.3 My Account
- 12.4 User Complaint
  - Screen Layout
- 12.5 Data Logging
- 12.6 Communities
  - User Profile
- 12.7 Training Channels
- 12.8 FAQ Database
Chapter 13 Training Operations
Chapter 14 Quick Link Operations
Chapter 15 MaxiScope Operations
- 15.1 Safety Information
- 15.2 Glossary
- 15.3 MaxiScope Module
- 15.4 Screen Layout and Operations
- 15.5 Troubleshooting
- 15.6 MaxiScope Firmware Update
Chapter 16 Digital Inspection Operations
- 16.1 Additional Accessories
- 16.2 Operations
Chapter 17 Maintenance and Service
- 17.1 Maintenance Instructions
- 17.2 Troubleshooting Checklist
- 17.3 About Battery Usage
- 17.4 Service Procedures
Chapter 18 Compliance Information
- FCC Compliance FCC ID: WQ8MAXISYSMY908
- SAR:
Chapter 19 Warranty
- 12-Month Limited Warranty
- This warranty does not apply to:

Getting Started Installing Computer Software

NOTE: The MaxiSys Printer runs automatically after the installation.

3.3.1 Printing Operation

This section describes how to receive file from the MaxiSys tablet and perform

printing through the computer:

 To perform printing through the computer

1. Install the MaxiSys Printer driver to the computer.

2. Make sure the display tablet is connected to the computer network,

either via WiFi or LAN, before printing. See 7.1.3 Printing Setting on

page 75 for more information.

3. Run the MaxiSys Printer program on the computer to open up the

printer interface.

4. Click Test Print to make sure the printer is working successfully.

5. Tap the Print button on the toolbar displayed in various applications

of the MaxiSys system. A temporary file will be created and sent to

the computer for printing.

6. The MaxiSys Printer will print the received file automatically when

the Auto Print option is checked.

If you need to print the document later, click the Open PDF file and

select the document, and double click the Print on the MaxiSys

Printer interface to start the printing.

NOTE: Make sure the computer installed with the Printing Services program is

connected to a printer.