RF-350 PROFESSIONAL VEHICLE SECURITY SYSTEM WITH KEYLESS ENTRY INSTALLATION & USERS MANUAL (For Authorized Dealers Only) Please register your product at www.autopageusa.
WIRING DIAGRAM 2
H1: MAIN 5 PIN WIRE HARNESS: 1. Red / White Wire: Parking Light Relay input 2. White Wire: Parking Light Relay Output 3. Black Wire: Ground to Vehicle FRAME 4. Brown Wire: Positive output To Siren 15A Fuse 5. Red Wire: +12V To Constant Battery Source H2: 8 PIN MINI CONNECTOR WIRE HARNESS: 1. BROWN/WHITE...(-) HORN OUTPUT (RELAY REQUIRED) 2. WHITE...DOME LIGHT / 3RD CHANNEL OUTPUT 3. VIOLET ...POSITIVE DOOR TRIGGER (+) INPUT * 4. BLUE...NEGATIVE INSTANT (-) INPUT 5. GREEN...
VACUUM OPERATED CENTRAL LOCKING Green Wire 86 87 87a Door Switch X Cut 30 85 3 Pin Plug To Alarm +12V 86 87 Compressor 87a 30 85 Blue Wire VACUUM OPERATED DOOR LOCKING SYSTEM: TYPICAL OF MERCEDES BENZ AND AUDI. Locate the wire under the driver's kick panel. Use the voltmeter connecting to ground, verify that you have the correct wire with the doors unlocked, the voltmeter will receive "12 volts". Lock the doors and the voltmeter will read "0 volt".
2 STEP DOOR UNLOCK WIRE CONNECTION FOR POSITIVE SWITCHED DOOR LOCKS +12V 8-Pin Plug From Alarm OEM Door Master Lock Switch H2/8 Gray Wire 87 Unlock 86 87A Existing Pos. Unlock Wire 30 H3/3 Green Wire Door Lock Lock 85 + 12V Existing Pos.
Note: If more than 4 transmitters are programmed, the system will only keep the last 4 transmitters and delete the others. ALARM FEATURE “A” PROGRAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. rd 2. Push the Valet switch 3 times and hold in on the 3 push. When a long chirp is heard, release the valet switch. You are now in the Alarm feature ‘I’ programming mode. 3. Press the transmitter button corresponding to the feature you want to program. a.
ALARM FEATURE “B” PROGRAMMING: 1 2 3 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. th Push the Valet switch 5 times and hold in on the 5 push. When a long chirp is heard, release the valet switch. You are now in the Alarm feature ‘B’ programming mode. Press the transmitter button corresponding to the feature you want to program.
ALARM FEATURE “C” PROGRAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. th 2. Push the Valet switch 7 times and hold on the 7 push until Three chirps with a long chirp is heard then release the valet switch. You are now in the Alarm feature ‘C’ programming mode. 3. Press and hold the transmitter button for two seconds to enter shock sensor program mode.
Operation Manual TRANSMITTER OPERATION: Transmitter Button System Function Remark Lock Doors & Arm System Panic function Press and Hold for 3 seconds Car Locator Under armed mode + Arm and Delete The 2 Stage Shock Sensor Silent Arming / Disarming - Unlock Doors & Disarm System Two Steps Door Unlock & Disarm System Trunk Release (Channel 2) Press twice within 3 seconds. Passive Arming By-pass While the system Disarmed. - Press twice within 3 seconds Ignition in "off" position.
/ hood / trunk, the security system LED will stop flashing. It will begin flashing again once all vehicle entrances are closed. 2. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time and the parking lights will flash [1] time. PASSIVE DOOR LOCKING: The vehicle doors will automatically lock after passive arming cycle has been completed. ACTIVE DISARMING – UNLOCK & DISARM: 1. Press the button on the transmitter. 2.
ANTI CAR-JACKING: (OPTIONAL) If alarm option is installed. Warning: If you don't need the carjacking function in this alarm system, be sure to set carjacking feature “OFF”. This system is default setting Car-jacking “OFF”. 1. TRANSMITTER ACTIVATE THE CAR JACKING: Press and hold + button on the transmitter for 1 second while the vehicle’s ignition is ON. The parking light will turns on for 1.5” seconds to indicate car jacking activated. 2. DOOR SWITCH ACTIVATES CAR JACKING: 1.
TRUNK RELEASE. Press and hold button on transmitter for two seconds to remote control the trunk release or other electric devices. CAR LOCATOR Press the button on the transmitter to active car locator function. The siren will chirp 6 times. The parking light will flash 12 times, allowing you to easily locate your car. P. PATHWAY ILLUMINATION When disarming the security system, the vehicle’s parking lights will stay on, illuminating a pathway to the vehicle.
CHANGING THE BATTERY IN YOUR TRANSMITTERS XT-33: The XT-33 transmitter uses two (2) 3-volt lithium ion batteries (#CR2016) that are sandwiched together with the (+) side facing upward. To replace the battery, you will need to use a small flat blade screwdriver. Locate the small notch on the lower right side of the transmitter case next to the key ring. Using the flat blade screwdriver, carefully pry the top case from the bottom case. It should snap apart after breaking the seal.
LIMITED LIFETIME WARRANTY PROVISIONS ( U.S. ,Continental U.S. and Canada Only) 1. Auto Page, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery.
You must register your product online at http://www.autopageusa.com to receive any warranty service. Please go to the customer service tab and select product registration. It is the purchaser’s responsibility to register this product for any future warranty service. Warning: Some batteries may contain Perchlorate What is Perchlorate? Perchlorate is both a naturally occurring and manmade contaminant increasingly found in groundwater, surface water and soil. Most perchlorate manufactured in the U.S.
960 Knox Street Unit B, Torrance, CA 90502 Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.
