RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY) THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY 1
BLUE...TRUNK/HOOD TRIGGER (-) INPUT BLACK/BLUE...4TH CHANNEL OUTPUT (200mA) RF-425 VIOLET...POSITIVE TRIGGER (+) INPUT YELLOW...IGNITION INPUT 5 - PIN GREEN...NEGATIVE TRIGGER (-) INPUT 10A WHITE...(+) LIGHT FLASH ORANGE...STARTER INTERUPT OUTPUT (RELAY REQUIRED) BLACK...(-) MAIN SYSTEM GROUND PINK...2 STEP DOOR UNLOCK (RELAY REQUIRED) BROWN...(+) SIREN OUTPUT WHITE/BLUE...3RD CHANNEL OUTPUT (200mA) GRAY...2ND CHANNEL OUTPUT 15A (200mA) RED...12V (+) MAIN POWER WHITE...
WIRING HARNESS MAIN 5 PIN WIRE HARNESS: 5 - PIN 10A WHITE...(+) LIGHT FLASH BLACK...(-) MAIN SYSTEM GROUND BROWN..(+) SIREN OUTPUT 15A RED...12V (+) MAIN POWER + - BATTERY BLUE/BLACK...(-) HORN OUTPUT 10 PIN MINI CONNECTOR WIRE HARNESS: BLUE...TRUNK/HOOD TRIGGER (-) INPUT BLACK/BLUE...4TH CHANNEL OUTPUT VIOLET...POSITIVE TRIGGER (+) INPUT YELLOW...IGNITION INPUT GREEN...NEGATIVE TRIGGER (-) INPUT ORANGE...STARTER INTERUPT OUTPUT (RELAY REQUIRED) PINK...
WIRING Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Tape wires that pass through holes on the firewall to prevent fraying. Be careful of sharp edges that may damage wires and causes short circuit. CAUTION: Do not connect the wire harness to the control module until all wiring to vehicle is complete. MAIN 5 PIN WIRE HARNESS: WHITE WIRE –PARKING LIGHT RELAY OUTPUT (+12 V 10A OUTPUT) -Connect the WHITE wire to the parking light wire coming from the headlight switch.
10-PIN MINI CONNECTOR WIRE HARNESS. 1. BLUE WIRE -- GROUND INSTANT TRIGGER INPUT -This wire is the ground trigger input wire for hood/trunk pin switches. 2. Black / BLUE WIRE – (-) 200mA Timer Control Channel 4 Output – This wire has a built-in user-programmable timer output that provides a ground through this wire. Press the transmitter and button at the same time. You may program the built-in timer to send a ground signal for any time interval between 1 second and 2 minutes.
8. WHITE/BLUE WIRE – PROGRAMMABLE OUTPUT – CHANNEL 3 OUTPUT (Factory default setting) This wire is built-in user-programmable timer output provides a ground through this wire. Press the + button on the transmitter. You may program the built-in timer to send a ground signal for any time interval between 1 second and 2 minutes. For instance, this timer output may be used to turn on the headlight with the remote control.
6 PIN DOOR LOCK CONNECTOR: 3-WIRE NEGATIVE BROWN UNLOCK SWITCH... N/C (87a) NOT USED LT. BLUE UNLOCK MOTOR... COMMON (30) VIOLET UNLOCK... N/O (87) WHITE LOCK SWITCH...N/C (87a) NOT USED LT. GREEN LOCK MOTOR... COMMON (30) 20A VIOLET/RED LOCK... N/O (87) LOCK UN LOCK GROUND 3-WIRE POSITIVE BROWN UNLOCK SWITCH... N/C (87a) NOT USED LT. BLUE UNLOCK MOTOR... COMMON (30) VIOLET UNLOCK... N/O (87) WHITE LOCK SWITCH...N/C (87a) NOT USED LT. GREEN LOCK MOTOR... COMMON (30) 20A VIOLET/RED LOCK...
5-WIRE REVERSE POLARITY BROWN UNLOCK SWITCH... N/C (87a) LT. BLUE UNLOCK MOTOR... COMMON (30) VIOLET UNLOCK... N/O (87) WHITE LOCK SWITCH...N/C (87a) LT. GREEN LOCK MOTOR... COMMON (30) 20A VIOLET/RED LOCK...
VACCUM DOOR LOCK SYSTEM BROWN WIRE LOCK BLUE WIRE VIOLET WIRE 405 6-PIN CONNECTOR UN LOCK (12v B+) WHITE WIRE BROWN FROM DOOR GREEN WIRE VIOLET / RED WIRE (GROUND) GREEN WIRE TO PUMP LOCK PUMP PROGRAMMING A. TRANSMITTER PROGRAMMING Enter: 1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds. 2. Push the Valet switch 2 times and hold in on the 2nd push, when a long chirp is heard then release the valet switch. You are now in the Transmitter programming mode.
ALARM FEATURE “A” PRORAMMING: 1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 3 times and hold in on the 3rd push, when a long chirp is heard then release the valet switch. You are now in the Alarm feature ‘A’ programming mode. 3. Press the transmitter button corresponding to the feature you want to program. a. The factory default settings is always [1] LED flash, [1] chirp. 4. Depress the transmitter button again to change the feature.
ALARM FEATURE “C” PRORAMMING: 1 Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2 Push the Valet switch 7 times and hold in on the 7th push, when a long chirp is heard, then release the valet switch. You are now in the Alarm feature ‘C’ programming mode. 3 Press the transmitter button corresponding to the feature you want to program. One Chirp / LED one pulse Factory Default Setting Two Chirps / LED two pulses Channel 2 Output = 2 sec.
960 Knox Street, Unit B Torrance, California 90502 Main Office: 310-323-1800 Technical Support: 800-262-2527 Ext. 461 (For Authorized Dealers Only) www.autopageusa.
