RS-1000 OLED PROFESSIONAL OLED 2-WAY 900 MHz. REMOTE CAR STARTER & 6 CHANNEL ALARM SYSTEM With Built-in Temperature Sensor And Serial Port Data Link OPERATION MANUAL Please register your product at: www.autopageusa.
OLED REMOTE TRANSCEIVER: A. OLED REMOTE DISPLAY……………………………….…..…………………………………..…………………… 4 The Remote Transceiver, XT-100 OLED B. CHARGING THE BATTERY ……….………………………………………………………………………….….. 4 C. MAIN PAGE …………………………………………………………………………………………………………… 5 D. SELECT THE TRANSCEIVER’S BUTTON CONFIGURATION …………………………………………. 6 E. SELECT THE TRANSCEIVER FEATURES …………………………………………..……………………….
E. TIMER START …………………………………………….…………….……………………….…..…………………… 19 3 (2 or 1) Hours Timer Start Daily Timer Start Cancel the Timer Start F. TEMPERATURE CHECK …………….……………………………………………….…...……….…………….….… 20 G. TO TURN OFF THE REMOTE START ……………………………………………….….…….………………….….…20 H. SHUT-DOWN INPUT FOR REMOTE STARTER …………………………….……………………………..………… 20 I. DISABLING THE REMOTE START SYSTEM …………………………….……………………..……………….….… 20 TEST MODE …………………..…………….……………………………………………….…...……….………..…….
REMOTE TRANSCEIVER (TX) A. OLED DISPLAY Name of Transmitter Clock / Timer Door Lock In – Range Indicator Door Unlock Alarm Status Temperature Car Jacking Bypass Shock Sensor (Zone 4) Battery Level Engine Running Melody Mode Count Down Timer Parking Timer Vibration Mode Alert Alarm Timer Start Antenna switch button OLED Display switch Engine Running Button Button 1 Button Button 2 Button Button 3 Button Button 4 Reset Hole B. CHARGE THE BATTERY The unit has a built-in 3.
AC Power Supply: The remote transceiver equipped AC POWER SUPPLY / AC ADAPTOR (Output Voltage: 4.2VDC – 5.5VDC and with same USB plug), then you can charge the battery indoors. This screen will be displayed while the battery of the Remote Transceiver is charging. C. MAIN PAGE: 1. Press the button, the screen will display the main page. button. The OLED screen will display the 2. When an icon is flashing on the OLED screen, press the details of the flashing icon.
Push the button, the alert alarm time will displayed. icon is While the flashing. Press button 2 to turn OFF the alert alarm timer. D. SELECT THE TRANSCEIVER’S BUTTON CONFIGURATION: Switch to select the transceiver button configuration. The OLED screen will 1. Spin the jog shuttle up display the transceivers button configuration you would like to select. 2. Within 5 seconds, press buttons 1, 2, 3 or 4 to select the remote controls “button configuration”.
E- P1- 1. “BUTTON BI” SETTING: Example: Set the “Button Bi Disable”. The unit has a short “bi” sound while pressing the buttons of the remote transceiver Spin down the switch to page 1. E- P1- 2. “BUTTON LOCK” SETTING: Spin down the switch to page 1. Press button 2 to change the setting. Press button 1 and it will display the previous setting. Example: Set the “Button Lock Enable”. Press button 1 to change the setting. Press button 2 and it will display the previous setting. D- P1- 3.
E- P1- 4. “DEMO MODE”: Spin down the switch To display the units demo mode Demo movie playing. Press button 4 to start Press any Button to exit. the Demo movie. to page 1. E- P2- 1. “POWER SAVE” SETTING: Example set the “Power Save Enable”. While in the power save mode, the LCD remote transceiver uses “0” current to save the battery power. Spin down the switch to page 2. Press button 1 to change the setting. Press button 1 and it will display the previous setting.
D- P3- 1. “TIMER / CLOCK” SETTINGS: Spin down the switch to page 3. Press button 2 to set the “minutes” digit to “20”. This can also be done with the jog shuttle. Example: set the clock to 08:20PM Press button 2 to set the ”hours” digit to “08”. This can also be done with the jog shuttle. Press button 1 and the ”hours” digit flashes for adjusting. Press button 1 and the ”A” digit flashes for adjusting. AM or PM. Press button 2 to set the “P”.
C- P3- 3. “COUNT DOWN TIMER” SETTING: Example: set the count down timer to 2:30 Note: When count down timer is triggered, press any button to stop the beeper. Spin down the switch to page 3. Press button 2 to set the ”minutes” digit to “30”. This can also be done with the jog shuttle. Press button 2 to set the ”hours” digit to “02”. This can also be done with the jog shuttle. Press button 3 and the ”hours” digit flashes for adjusting.
D- P4- 1. “NAME OF TX ” SETTING: Spin down the switch to page 4. Press button 1 and the “-” flashes for setting. Example Set Name of Transceiver 1 to MIKE Press button 1 and the “-” flashes for setting. Spin down the switch to set the “M”. Press button 1 and the “-” flashes for setting. Spin up the ” switch to set the ”I”. Spin down the Press button 1 and the “-” flashes for setting. Spin up the switch to set the ”E”. Press button 3 and the setting is done. switch to set the ”K”. D- P5- 1.
D- P6- 2. SET TO DEFAULTS: Spin down the Press buttons 1 & 2 at same time to set the defaults. Press button 4. switch to page 6. OPERATION: A. REMOTE TRANSMITTER OPERATION: Transmitter Button 1 then (3-second) + + (2-second) 2 - 3 (3-second) - 4 + + + II System Function Lock Doors & Arm System / Button 1 Arm and Bypass Zone 4. Shock Sensor Arm System and Hidden, (Silent) Alarm Function Car Locator Panic function Silent Arming / Disarming Active Anti Car-Jacking Mode.
E. ACTIVE ARMING – LOCK & ARM: 1. Press the button on the transmitter. 2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle door will lock upon arming when interfaced with the security system. AJAR WARNING: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.
SILENT DISARMING: Spin up the switch to the page 1 and then press the “Silent Disarm” button or press the transmitter and buttons at the same time to disarm your security system, No chirp sound will be heard, arm and disarm confirmation will be through the vehicles parking lights only. TAMPER DISARMING: If alarm triggered, upon disarming the system, the siren will chirp 4 times and the parking light will flash 3 times.
transmitter to a parking attendants or a garage mechanic. When the system is in valet mode, all alarm function and remote start functions are bypassed, however the remote panic feature and remote door locks will remain operational. To use the valet mode, the system must first be disarmed. Enter Valet Mode: 1. From the disarmed condition, turn the ignition to the “ON” position. 2. Push and hold valet switch for 2 seconds until the LED turns on solid.
Here’s how the “Noise Abatement Circuit” works: If the alarm triggers five times, each time the same sensor (zone 4) is triggered the “Noise Abatement Circuit” will interpret this pattern of triggers as false alarms. After the fifth trigger, the “Noise Abatement Circuit” ignores, or bypasses that sensor until any other sensor or switch is triggered.
P. DRIVER PAGING / LOST & FOUND This feature is useful in the event that someone wants to page the driver of the parked vehicle or you cannot find his OLED remote transceiver. Indoor Driving Paging If the ignition switch is in the “off” position, press and hold the valet switch for 2 seconds to page the driver. One chirp sound shall be emitted from the vehicle and the paging melody will sound from your Remote OLED transceiver. “DRIVER PAGING” indication will flash on the OLED screen.
For 2-way OLED Remote Control Transceiver: A maximum of four vehicle’s security systems can be controlled by this transceiver. TX1 Red Vehicle TX2 Blue Vehicle TX3 Yellow Vehicle The four transmitters will screen, you can chose Now you can press button to remote control The “TX 3” yellow one of the four vehicle’s security be display on the OLED transmitters to control Spin up the To page 6 switch TX4 Green Vehicle system. your vehicle security Pressing button 3 will set system. the remote. .
2. Press the brake pedal. Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down. C. TEMPORARY STOP FEATURE: This feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate control on. button on the transmitter. Twice if safety start has been 1.
F. TEMPERATURE CHECK You can monitor the present indoor temperature of the passenger compartment through the OLED screen, before cooling or heating your vehicle. Spin up the switch to the page 4 and then press the “Monitor TEMP.” button; the in-door temperature will be shown on the OLED screen. This reading may be higher than actual ambient temperature due to the greenhouse effect and is relative only to the inside vehicle temperature. G.
LIMITED LIFETIME WARRANTY PROVISIONS ( U.S. ,Continental U.S. and Canada Only) 1. Auto Page, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery.
Warning: Some batteries may contain Perchlorate What is Perchlorate? Perchlorate is both a naturally occurring and manmade contaminant increasingly found in groundwater, surface water and soil. Most perchlorate manufactured in the U.S. is used as an ingredient in solid fuel for rockets and missiles. In addition, perchlorate-based chemicals are also used in the construction of highway safety flares, fireworks, pyrotechnics, explosives, common batteries, and automobile restraint systems.
[ This page left blank intentionally ] RS1000 OP 1/07 23
960 Knox Street Unit B, Torrance, CA 90502 Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.
